English dropdown-ico

Manual FSP/Fortron Knight KN-1102TS

18 pages Not applicable
Download

Go to site of 18

Summary
  • FSP/Fortron Knight KN-1102TS - page 1

    1K/2K/3K Online UPS Uninterruptible P ower Supply S ystem User Manual ...

  • FSP/Fortron Knight KN-1102TS - page 2

    T able of Contents 1. Importa nt Safety W arning ............................................................................................... 1 1-1. T ra nsportation ..................................................................................................... 1 1- 2. Prepar ation .......................................................... ...

  • FSP/Fortron Knight KN-1102TS - page 3

    1 1. Importan t Safety Warnin g Please comply with all warnings and operating instructions in this manual strictly. Save this manual properly and r ead carefully the following instructions before installing the unit. Do not operate this unit bef ore reading through all safety information and operating instructions carefully 1-1. Transportation  ...

  • FSP/Fortron Knight KN-1102TS - page 4

    2 1-5. Maintenance, service and faults  The UPS system operates wit h hazardous voltages. Repa irs may be carried out only by qualified maintenance personnel.  Caution - risk of electric shock. Even after the unit is disconnected from the mains (building wiring outlet), components inside the UPS system are still connected to the battery and e ...

  • FSP/Fortron Knight KN-1102TS - page 5

    3 2. Installation and setup NOTE: Before installation, please inspect t he unit. Be sure that nothing inside the package is damaged. Please keep t he original package in a saf e place for f uture use. NOTE: There a re two diff erent t ypes of online UPS: standa rd a nd long-run mod els. Plea se ref er to the following model ta ble. Model T ype Mode ...

  • FSP/Fortron Knight KN-1102TS - page 6

    4 8. Output circuit break e r 9. Output terminal 2-2. Setup the UPS Step 1: UPS input connection Plug the UPS into a two-pole, three -wire, grounded recept a cle only . Avoid using extension cords. The power cord is supplied in t he UPS packag e. Step 2: UPS output connection  For socket -type outputs, simply connect devices to the ou tlets . ? ...

  • FSP/Fortron Knight KN-1102TS - page 7

    5 Step 5: Install software For optimal computer system protection, install UPS monitoring software t o fully configure UPS shutdown. Y ou may insert provided CD into CD-ROM to install the monitoring software. If not, please follow steps b elow to download and install monitoring software from the internet: 1. Go to the website http://www.power-softw ...

  • FSP/Fortron Knight KN-1102TS - page 8

    6 3. Operations 3-1. Button operation Button Function ON/Mute Button  Turn on the UPS: Pre ss and hold ON/Mute button for at least 2 secon ds to turn on the UPS.  Mute the a larm: When the UPS is on ba ttery mod e, press and hold this button for at least 5 seconds to disa ble or e nable the alarm system. But it ’ s not applied to the situat ...

  • FSP/Fortron Knight KN-1102TS - page 9

    7 Display Function Remaining backup time information Indicates the remaining backup time in pie chart. Indicates th e remaining ba ckup time in numbers. H: hours, M: minute, S: se cond Fault information Indicates that the warning and fault occurs. Indicates the warning and fault codes, a nd the codes are listed in details in 3-5 section. Mute opera ...

  • FSP/Fortron Knight KN-1102TS - page 10

    8 3-3. Audible Alarm Battery Mode Sounding every 4 seconds Low Battery Sounding every second Overload Sounding twice every second Fault Continuously sounding Bypass Mode Sounding every 10 seconds 3-4. LCD display wordings index Abbreviation Display content Meaning ENA En able DIS Disable ESC Escape HLS High loss LLS Low loss BA T Battery CF Convert ...

  • FSP/Fortron Knight KN-1102TS - page 11

    9 the following output voltage: 10 0: presents output voltage is 100Vac 110: presents output volta ge is 110Vac 115: presents output voltage is 115Vac 120: presents output voltage is 120Vac 127: presents output voltage is 127Vac  02: Frequency Converter enable /disable Interface Setting Parameter 2 & 3: Ena ble or disable converter mode. You ...

  • FSP/Fortron Knight KN-1102TS - page 12

    10  06: Bypass enable/disable when UPS is off Interface Setting Parameter 3: Enable or disable Bypass function. You may choose the following two options: ENA: Bypass enable DIS: Bypass disable  07: Bypass voltage range setting Interface Setting Parameter 2 & 3: Set the acceptable high volta ge point and acceptable low voltage point for By ...

  • FSP/Fortron Knight KN-1102TS - page 13

    11 3-6. Operating Mode Description Operating mode Description LCD display Online mode When the input voltage is within acceptable range, UPS will provide pure and stable AC power to output. T he UPS will also charge the battery at online mode. ECO mode Energy saving mode: When the input voltage is within voltage regulation range, UPS will bypass vo ...

  • FSP/Fortron Knight KN-1102TS - page 14

    12 3-8. Warning indicator W arning Icon ( flashing) Alarm Low Battery Sounding every second Overload Sounding twice every second Battery is not connected Sounding every second Over Charge Sounding every second Over temper ature Sounding every second Charger failure Sounding every second Out of bypass v oltage ra nge Sounding every second ...

  • FSP/Fortron Knight KN-1102TS - page 15

    13 4. Troubleshoo ting If the UPS s ystem does not oper ate correctly , please solve the problem by using the table below. Symptom Possible cause Remedy No indication and alarm even though the mains is normal. The AC input power is not connected well. Check if input power cord f irmly connected to the mains. The AC input is connected to the UPS out ...

  • FSP/Fortron Knight KN-1102TS - page 16

    14 Symptom Possible cause Remedy Battery backup time is shorter th an nominal v alue Batteries are not f ully charged Charge the bat teries for at least 5 hours and then check capacity . If the problem still persists, consult your dealer . Batteries defect Contact your dealer to replace the batt ery . F ault code is shown as 05 on LCD display . A t ...

  • FSP/Fortron Knight KN-1102TS - page 17

    15 5. Storage and M aintenance Operation The UPS system contains no user -serviceable parts. If the battery s ervice life (3~5 years at 25° C ambient temperature) has been exceeded, the batteries mus t be replaced. In this case , please contact your dealer. Storage Before storing, charge the UPS 5 hours. Store the UPS covered and upright in a cool ...

  • FSP/Fortron Knight KN-1102TS - page 18

    16 6. Specifications CAPACITY* 1000 VA / 800 W 2000 VA / 1600 W 3000 VA / 2400 W INPUT Voltage Range Low Line Transfer 160VAC/140VAC/120VAC /110VAC± 5% ( based on load percentage 100% - 80 % / 80 % - 70 % / 70 - 60 % / 60 % - 0 ) Low Line Comeback 16 8VAC/14 8VAC/128VAC/1 18VAC ± 5 % ( based on load percentage 100% - 80 % / 80 % - 70 % / 7 0 - 60 ...

Manufacturer FSP/Fortron Category Uninterruptible power supply (

Documents that we receive from a manufacturer of a FSP/Fortron Knight KN-1102TS can be divided into several groups. They are, among others:
- FSP/Fortron technical drawings
- Knight KN-1102TS manuals
- FSP/Fortron product data sheets
- information booklets
- or energy labels FSP/Fortron Knight KN-1102TS
All of them are important, but the most important information from the point of view of use of the device are in the user manual FSP/Fortron Knight KN-1102TS.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals FSP/Fortron Knight KN-1102TS, service manual, brief instructions and user manuals FSP/Fortron Knight KN-1102TS. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product FSP/Fortron Knight KN-1102TS.

Similar manuals

A complete manual for the device FSP/Fortron Knight KN-1102TS, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use FSP/Fortron Knight KN-1102TS by users. Manuals are usually written by a technical writer, but in a language understandable to all users of FSP/Fortron Knight KN-1102TS.

A complete FSP/Fortron manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual FSP/Fortron Knight KN-1102TS - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the FSP/Fortron Knight KN-1102TS, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the FSP/Fortron Knight KN-1102TS, that we can find in the current document
3. Tips how to use the basic functions of the device FSP/Fortron Knight KN-1102TS - which should help us in our first steps of using FSP/Fortron Knight KN-1102TS
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with FSP/Fortron Knight KN-1102TS
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of FSP/Fortron Knight KN-1102TS in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning FSP/Fortron Knight KN-1102TS?

Use the form below

If you did not solve your problem by using a manual FSP/Fortron Knight KN-1102TS, ask a question using the form below. If a user had a similar problem with FSP/Fortron Knight KN-1102TS it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)