Bedienungsanleitung Pelco CX9504

20 Seiten 0.18 mb
Download

Zur Seite of 20

Summary
  • Pelco CX9504 - page 1

    ® Pelco • 3500 Pelco W ay • Clovis, CA 93612-5699 • USA • www .pelco.com (800) 289-9100 or (1-559) 292-1981 • F AX (800) 289-9150 or (1-559) 292-3827 International customers call (1-559) 292-1981 or F AX (1-559) 348-1 120 CX9500/CX9504 Receivers Coaxitr on ® System Installation/Operation Manual C505M-B (4/97) F U S E 1 4 5 9 1 5 1 0 2 2 ...

  • Pelco CX9504 - page 2

    18 Pelco Manual C505M-B (4/97) CONTENTS Section Page 1.0 GENERAL .................................................................................................. 1 1.1 IMPORT ANT SAFEGUARDS AND WARNINGS ............................... 1 2.0 DESCRIPTION .......................................................................................... 2 2. ...

  • Pelco CX9504 - page 3

    Pelco Manual C505M-B (4/97) 19 LIST OF ILLUSTRA TIONS Figur e Page 1 T ypical Coaxitron Application ............................................................. 3 2 T ypical RS-485 Control Applications .................................................. 4 3 Receiver Connector Locations ........................................................... 5 4 ...

  • Pelco CX9504 - page 4

    20 Pelco Manual C505M-B (4/97) (This page intentionally left blank.) iv ...

  • Pelco CX9504 - page 5

    Pelco Manual C505M-B (4/97) 1 Please thoroughly familiarize yourself with the information in this manual prior to installation and operation. 1.0 GENERAL 1.1 IMPORT ANT SAFEGUARDS AND W ARNINGS Prior to installation and use of this product, the following W ARNINGS should be observed. 1. Installation and servicing should only be done by Qualified Se ...

  • Pelco CX9504 - page 6

    2 Pelco Manual C505M-B (4/97) 2.0 DESCRIPTION The Coaxitron ® System 9500 receivers are available in two control formats and work with all Coaxitron controls. The control formats are as follows: 1. CX9500 Coaxitron control 2. CX9504 RS-485 4-wire control Standard features for all receivers include: • Full PTZ (Pan/tilt and Zoom) Coaxitron contro ...

  • Pelco CX9504 - page 7

    Pelco Manual C505M-B (4/97) 3 3.0 INST ALLA TION 3.1 SELECTING THE CORRECT RECEIVER FOR YOUR APPLICA TION Successful installation must include proper application planning. The trade-offs and application hints that should be considered for each receiver type are discussed in the following subsections. 3.1.1 The CX9500 Coaxitron VIS Contr ol System A ...

  • Pelco CX9504 - page 8

    4 Pelco Manual C505M-B (4/97) Figure 2. T ypical RS-485 Control Applications 3.1.2 The CX9504 4-Wire RS-485 Contr ol System This system is used in applications where multiple receivers will listen to a single control channel, but duplex operation is desired. The RS-485 system presents sev- eral unique installation requirements. These requirements a ...

  • Pelco CX9504 - page 9

    Pelco Manual C505M-B (4/97) 5 3.2 CONNECTING THE RECEIVER Connecting the receiver involves mating the correct connector assembly to the appropriate receiver connector (J6 or J7) on the Coaxitron unit. See Figure 3. Receiver connector locations are listed as follows: BNC-1** Video input from camera BNC-2** Video output and Coaxitron input J6 Standar ...

  • Pelco CX9504 - page 10

    6 Pelco Manual C505M-B (4/97) Figure 4. Connector Assembly 3.2.1 Connector Assembly If you did not order a pre-assembled connector , assemble the connector parts ac- cording to the instructions below . Detail B, below , reflects the pin arrangement spe- cific to CX9500/CX9504 Receivers. Refer to Figure 4 during assembly . For best results use an AM ...

  • Pelco CX9504 - page 11

    Pelco Manual C505M-B (4/97) 7 4.0 OPERA TION Upon applying power , the receiver will perform its self-test functions. These diag- nostics determine the receiver , pan and tilt, lens and camera configuration by exer- cising each. The results are reported by text superimposed on the video if the text generator is preset (ZS versions). All versions ar ...

  • Pelco CX9504 - page 12

    8 Pelco Manual C505M-B (4/97) 5.0 CX9500 RECEIVER BOARD DESCRIPTIONS The CX9500 Receiver contains three boards: the Mother Board, the Option Board, and the Power Supply Board. Gaining access to the board slot locations can be seen in Figure 5. As part of any operational set-up, the Option and Power Supply Boards must be pulled and configured. This ...

  • Pelco CX9504 - page 13

    Pelco Manual C505M-B (4/97) 9 5.2 OPTION BOARD This board contains all the circuitry required for all options. The components will be loaded or not loaded according to the model being built. Preset circuits are loaded for preset (PP). Receiver Address circuits are loaded for the 9504 versions of the receiver . The RS-485 drivers are only loaded for ...

  • Pelco CX9504 - page 14

    10 Pelco Manual C505M-B (4/97) Figure 6. Options Board Address Settings 2 2 22 2222 76 54 32 10 SW1 SW2 SW3 SW4 SW5 SW6 SW7 SW8 ON RECEIVER ADDRESS Binary Weight Position Specific Decimal Equivalent 128 64 32 16 8 4 2 1 1 2 3 4 5 6 15 255 0 0 0000 01 0 0 0000 10 000 0 00 11 000 001 00 0 0 0001 01 0 0 0001 10 0 0 0011 11 1 1 1111 11 8 7 6 5 4 3 2 1 ...

  • Pelco CX9504 - page 15

    Pelco Manual C505M-B (4/97) 11 Figure 8. V ariable Speed Power Supply Board Figure 7. Universal Power Supply Board JP2 JP4 JP6 JP8 JP10 JP12 JP14 JP16 JP18 JP1 JP3 JP5 JP7 JP9 JP11 JP13 JP15 JP17 Typical Jumper Wire supplied in plastic bag along with fuses Universal AC Power Suppy Board JP2 JP8 JP7 JP9 JP4 JP6 JP10 JP14 JP16 JP18 JP15 JP17 JP12 JP1 ...

  • Pelco CX9504 - page 16

    12 Pelco Manual C505M-B (4/97) W ARNING: The AC line voltage used to power the receiver/driver is the same voltage that is fed through the pan/tilt into the enclosure as “en- closure power”, which also supplies the heaters and blower where appli- cable. This voltage is not selectable. INPUT VOL T AGE 24 V AC 120 V AC 230 V AC Fuse 2 AMP 1 AMP 1 ...

  • Pelco CX9504 - page 17

    Pelco Manual C505M-B (4/97) 13 6.0 FIRMW ARE DESCRIPTIONS 6.1 BAUD RA TES The hardware architecture between the controller and receiver is an RS-485 circuit designated the “control channel”. The baud rate is currently set to 2400 baud. The information is processed by the receiver every 16 ms. Higher baud rates are pos- sible by increasing the r ...

  • Pelco CX9504 - page 18

    14 Pelco Manual C505M-B (4/97) 7.0 SPECIFICA TIONS ELECTRICAL Input Voltage (50/60 Hz): Standard Version 24, 120, 230 VAC VS Version 120, 230 VAC Power Consumption (excluding PTZ): Standard Version 6 watts VS version 6 watts P/T Output Voltages: Standard Version 24, 120, 230 VAC VS Version 12 VDC PWM at 15 KHz P/T Output Currents : Standard Version ...

  • Pelco CX9504 - page 19

    Pelco Manual C505M-B (4/97) 15 MECHANICAL Connectors: P/T 37-pin CPC Options 37-pin CPC Video 2 BNCs Power 3-wire #18 Awg Fuse 2 AG, 1/2 amp GENERAL Ambient Operating Temperature: -4 ° to 140 ° F (-20 ° to 60 ° C) Dimensions: See Figure 9. Figure 9. CM9500 Series Receiver/Driver Dimension Drawing 9.14 (23.22) 8.36 (21.23) 7.16 (18.18) 5.88 (14. ...

  • Pelco CX9504 - page 20

    16 Pelco Manual C505M-B (4/97) 8.0 WARRANTY AND RETURN INFORMA TION Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. Endura and ExSite are trademarks of Pelco. © Copyright 1997, Pelco. All rights reserved. WARRANTY Pelco will repair or replace, without charge, any merchandise proved defectiv ...

Produzent Pelco Kategorie Home Security System

Dokumente, die wir vom Produzenten des Geräts Pelco CX9504 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Pelco
- Bedienungsanleitungen CX9504
- Produktkarten Pelco
- Informationsbroschüren
- oder Energieetiketten Pelco CX9504
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Pelco CX9504.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Pelco CX9504, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Pelco CX9504. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Pelco CX9504 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Pelco CX9504, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Pelco CX9504 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Pelco CX9504 verständlich ist.

Eine gänzliche Bedienungsanleitung von Pelco sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Pelco CX9504 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Pelco CX9504 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Pelco CX9504, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Pelco CX9504 - die uns die ersten Schritte während der Nutzung von Pelco CX9504 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Pelco CX9504 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Pelco CX9504 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Pelco CX9504?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Pelco CX9504 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Pelco CX9504 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)