English dropdown-ico

Manual Pelco CX9504

20 pages 0.18 mb
Download

Go to site of 20

Summary
  • Pelco CX9504 - page 1

    ® Pelco • 3500 Pelco W ay • Clovis, CA 93612-5699 • USA • www .pelco.com (800) 289-9100 or (1-559) 292-1981 • F AX (800) 289-9150 or (1-559) 292-3827 International customers call (1-559) 292-1981 or F AX (1-559) 348-1 120 CX9500/CX9504 Receivers Coaxitr on ® System Installation/Operation Manual C505M-B (4/97) F U S E 1 4 5 9 1 5 1 0 2 2 ...

  • Pelco CX9504 - page 2

    18 Pelco Manual C505M-B (4/97) CONTENTS Section Page 1.0 GENERAL .................................................................................................. 1 1.1 IMPORT ANT SAFEGUARDS AND WARNINGS ............................... 1 2.0 DESCRIPTION .......................................................................................... 2 2. ...

  • Pelco CX9504 - page 3

    Pelco Manual C505M-B (4/97) 19 LIST OF ILLUSTRA TIONS Figur e Page 1 T ypical Coaxitron Application ............................................................. 3 2 T ypical RS-485 Control Applications .................................................. 4 3 Receiver Connector Locations ........................................................... 5 4 ...

  • Pelco CX9504 - page 4

    20 Pelco Manual C505M-B (4/97) (This page intentionally left blank.) iv ...

  • Pelco CX9504 - page 5

    Pelco Manual C505M-B (4/97) 1 Please thoroughly familiarize yourself with the information in this manual prior to installation and operation. 1.0 GENERAL 1.1 IMPORT ANT SAFEGUARDS AND W ARNINGS Prior to installation and use of this product, the following W ARNINGS should be observed. 1. Installation and servicing should only be done by Qualified Se ...

  • Pelco CX9504 - page 6

    2 Pelco Manual C505M-B (4/97) 2.0 DESCRIPTION The Coaxitron ® System 9500 receivers are available in two control formats and work with all Coaxitron controls. The control formats are as follows: 1. CX9500 Coaxitron control 2. CX9504 RS-485 4-wire control Standard features for all receivers include: • Full PTZ (Pan/tilt and Zoom) Coaxitron contro ...

  • Pelco CX9504 - page 7

    Pelco Manual C505M-B (4/97) 3 3.0 INST ALLA TION 3.1 SELECTING THE CORRECT RECEIVER FOR YOUR APPLICA TION Successful installation must include proper application planning. The trade-offs and application hints that should be considered for each receiver type are discussed in the following subsections. 3.1.1 The CX9500 Coaxitron VIS Contr ol System A ...

  • Pelco CX9504 - page 8

    4 Pelco Manual C505M-B (4/97) Figure 2. T ypical RS-485 Control Applications 3.1.2 The CX9504 4-Wire RS-485 Contr ol System This system is used in applications where multiple receivers will listen to a single control channel, but duplex operation is desired. The RS-485 system presents sev- eral unique installation requirements. These requirements a ...

  • Pelco CX9504 - page 9

    Pelco Manual C505M-B (4/97) 5 3.2 CONNECTING THE RECEIVER Connecting the receiver involves mating the correct connector assembly to the appropriate receiver connector (J6 or J7) on the Coaxitron unit. See Figure 3. Receiver connector locations are listed as follows: BNC-1** Video input from camera BNC-2** Video output and Coaxitron input J6 Standar ...

  • Pelco CX9504 - page 10

    6 Pelco Manual C505M-B (4/97) Figure 4. Connector Assembly 3.2.1 Connector Assembly If you did not order a pre-assembled connector , assemble the connector parts ac- cording to the instructions below . Detail B, below , reflects the pin arrangement spe- cific to CX9500/CX9504 Receivers. Refer to Figure 4 during assembly . For best results use an AM ...

  • Pelco CX9504 - page 11

    Pelco Manual C505M-B (4/97) 7 4.0 OPERA TION Upon applying power , the receiver will perform its self-test functions. These diag- nostics determine the receiver , pan and tilt, lens and camera configuration by exer- cising each. The results are reported by text superimposed on the video if the text generator is preset (ZS versions). All versions ar ...

  • Pelco CX9504 - page 12

    8 Pelco Manual C505M-B (4/97) 5.0 CX9500 RECEIVER BOARD DESCRIPTIONS The CX9500 Receiver contains three boards: the Mother Board, the Option Board, and the Power Supply Board. Gaining access to the board slot locations can be seen in Figure 5. As part of any operational set-up, the Option and Power Supply Boards must be pulled and configured. This ...

  • Pelco CX9504 - page 13

    Pelco Manual C505M-B (4/97) 9 5.2 OPTION BOARD This board contains all the circuitry required for all options. The components will be loaded or not loaded according to the model being built. Preset circuits are loaded for preset (PP). Receiver Address circuits are loaded for the 9504 versions of the receiver . The RS-485 drivers are only loaded for ...

  • Pelco CX9504 - page 14

    10 Pelco Manual C505M-B (4/97) Figure 6. Options Board Address Settings 2 2 22 2222 76 54 32 10 SW1 SW2 SW3 SW4 SW5 SW6 SW7 SW8 ON RECEIVER ADDRESS Binary Weight Position Specific Decimal Equivalent 128 64 32 16 8 4 2 1 1 2 3 4 5 6 15 255 0 0 0000 01 0 0 0000 10 000 0 00 11 000 001 00 0 0 0001 01 0 0 0001 10 0 0 0011 11 1 1 1111 11 8 7 6 5 4 3 2 1 ...

  • Pelco CX9504 - page 15

    Pelco Manual C505M-B (4/97) 11 Figure 8. V ariable Speed Power Supply Board Figure 7. Universal Power Supply Board JP2 JP4 JP6 JP8 JP10 JP12 JP14 JP16 JP18 JP1 JP3 JP5 JP7 JP9 JP11 JP13 JP15 JP17 Typical Jumper Wire supplied in plastic bag along with fuses Universal AC Power Suppy Board JP2 JP8 JP7 JP9 JP4 JP6 JP10 JP14 JP16 JP18 JP15 JP17 JP12 JP1 ...

  • Pelco CX9504 - page 16

    12 Pelco Manual C505M-B (4/97) W ARNING: The AC line voltage used to power the receiver/driver is the same voltage that is fed through the pan/tilt into the enclosure as “en- closure power”, which also supplies the heaters and blower where appli- cable. This voltage is not selectable. INPUT VOL T AGE 24 V AC 120 V AC 230 V AC Fuse 2 AMP 1 AMP 1 ...

  • Pelco CX9504 - page 17

    Pelco Manual C505M-B (4/97) 13 6.0 FIRMW ARE DESCRIPTIONS 6.1 BAUD RA TES The hardware architecture between the controller and receiver is an RS-485 circuit designated the “control channel”. The baud rate is currently set to 2400 baud. The information is processed by the receiver every 16 ms. Higher baud rates are pos- sible by increasing the r ...

  • Pelco CX9504 - page 18

    14 Pelco Manual C505M-B (4/97) 7.0 SPECIFICA TIONS ELECTRICAL Input Voltage (50/60 Hz): Standard Version 24, 120, 230 VAC VS Version 120, 230 VAC Power Consumption (excluding PTZ): Standard Version 6 watts VS version 6 watts P/T Output Voltages: Standard Version 24, 120, 230 VAC VS Version 12 VDC PWM at 15 KHz P/T Output Currents : Standard Version ...

  • Pelco CX9504 - page 19

    Pelco Manual C505M-B (4/97) 15 MECHANICAL Connectors: P/T 37-pin CPC Options 37-pin CPC Video 2 BNCs Power 3-wire #18 Awg Fuse 2 AG, 1/2 amp GENERAL Ambient Operating Temperature: -4 ° to 140 ° F (-20 ° to 60 ° C) Dimensions: See Figure 9. Figure 9. CM9500 Series Receiver/Driver Dimension Drawing 9.14 (23.22) 8.36 (21.23) 7.16 (18.18) 5.88 (14. ...

  • Pelco CX9504 - page 20

    16 Pelco Manual C505M-B (4/97) 8.0 WARRANTY AND RETURN INFORMA TION Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. Endura and ExSite are trademarks of Pelco. © Copyright 1997, Pelco. All rights reserved. WARRANTY Pelco will repair or replace, without charge, any merchandise proved defectiv ...

Manufacturer Pelco Category Home Security System

Documents that we receive from a manufacturer of a Pelco CX9504 can be divided into several groups. They are, among others:
- Pelco technical drawings
- CX9504 manuals
- Pelco product data sheets
- information booklets
- or energy labels Pelco CX9504
All of them are important, but the most important information from the point of view of use of the device are in the user manual Pelco CX9504.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Pelco CX9504, service manual, brief instructions and user manuals Pelco CX9504. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Pelco CX9504.

Similar manuals

A complete manual for the device Pelco CX9504, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Pelco CX9504 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Pelco CX9504.

A complete Pelco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Pelco CX9504 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Pelco CX9504, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Pelco CX9504, that we can find in the current document
3. Tips how to use the basic functions of the device Pelco CX9504 - which should help us in our first steps of using Pelco CX9504
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Pelco CX9504
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Pelco CX9504 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Pelco CX9504?

Use the form below

If you did not solve your problem by using a manual Pelco CX9504, ask a question using the form below. If a user had a similar problem with Pelco CX9504 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)