Bedienungsanleitung S&S Cycle Motorcycle Accessories

20 Seiten 0.3 mb
Download

Zur Seite of 20

Summary
  • S&S Cycle Motorcycle Accessories - page 1

    1 Instruction Sheet #51-1 160 04-28-04 Copyright®, 2003 by S&S Cycle, Inc. All rights reserved. Printed in the U.S.A. Because e v ery industry has a leader S&S T win Cam Style Engine Assembly and Installation Instructions S & S Cycle , I nc. 14025 County Highway G Box 215 V iola, W isconsin 54664 Phone: 608-627-2080 • Fax: 608-627-14 ...

  • S&S Cycle Motorcycle Accessories - page 2

    2 SAFE INST ALLA TION AND OPERA TION RULES: Before installing any S&S engine part, it is your responsibility to read and follow all instructions. The rules below are for your personal safety , and must be kept in mind at all times. ● Gasoline is extremely flammable and explosive under certain conditions, and toxic when inhaled. Do not smoke a ...

  • S&S Cycle Motorcycle Accessories - page 3

    S&S Basic T win Cam Style Engines for Evolution Style Chassis * Displacement Bore Stroke Fuel System Finish Assembled Part Number Natural 31-9340 124" 4 1 ⁄ 8 "4 5 ⁄ 8 " Carburetor 1 Black 31-9341 Natural 31-9343 124" 4 1 ⁄ 8 "4 5 ⁄ 8 " S&S VFI 2 Black 31-9344 S&S Basic T win Cam Style Engines f o r ...

  • S&S Cycle Motorcycle Accessories - page 4

    B. Additional Features: ● Greater overall strength than stock crankcases, especially in the front motor mount, an important consideration in high performance applications. ● All oil passages between the crankcase and cam support plate are o-ring sealed. ● Compatible with stock components. Use stock oil pump, cam support plate, gear cover , et ...

  • S&S Cycle Motorcycle Accessories - page 5

    5 C. Modification Notes S&S Cycle cautions against modifying these crankcases due to the possibility of damaging or weakening them. Modifying S&S crankcases in any fashion voids all manufacturer warranties. Should the customer elect to modify the crankcases regardless, it is imperative that they and the information tag attached to them be i ...

  • S&S Cycle Motorcycle Accessories - page 6

    6 CAUTION - Improper alignment of engine and frame mounts may cause abnormal stresses resulting in damage to crankcases or other parts. 2. T est-fit instructions for T win Cam style cases with Evo Style motor mounts. 1. Assemble case halves using case bolts. T ighten to snug. T orquing bolts to final specification is not necessary . 2. Clean frame ...

  • S&S Cycle Motorcycle Accessories - page 7

    CAUTION - Failure to observe the above may result in engine damage not covered under warranty . 1. Crankcase preparation before assembly . NOTES - S&S crankcases are sold in matched sets only . Individual case halves are not available. S&S T win Cam style engines are shipped with cylinder studs installed Before assembling engine, verify tha ...

  • S&S Cycle Motorcycle Accessories - page 8

    3. Coat right main bearing and race with assembly lube. , then join left and right crankcase halves. 4. T ighten 5⁄16" case bolts to 18 ft-lbs, tighten 1⁄4" center bolt to 120 in-lbs. in the sequence shown. See Figure 1. 5. Install drive sprocket spacer and sprocket shaft oil seal in main bearing race of left case. Spring side of seal ...

  • S&S Cycle Motorcycle Accessories - page 9

    9 Use tool to guide bearing rollers onto inner race Picture E9 Picture E12 Picture E10 Picture E13 Picture E1 1 Figure 1 Picture E7 1 2 3 4 5 6 7 8 9 Picture E8 ...

  • S&S Cycle Motorcycle Accessories - page 10

    10 2. Inspect pistons, especially areas around machined surfaces such as ring grooves and wristpin holes. De-burr as necessary , taking care to remove particles that could become dislodged inside engine. 3. Measure ring end gaps and adjust as necessary . See Pictures E13 and E14 a. Compression ring end-gaps should be between .017” to .025”. b. ...

  • S&S Cycle Motorcycle Accessories - page 11

    11 5. Install cylinder heads 1. Place head gasket on top of cylinder . Locate on dowels installed in cylinder . NOTE - Head gaskets should be installed clean and dry . 2. Before installing heads spin each head bolt down on its respective stud to be sure threads are clean and free of contamination. Place a drop or two of oil on threads and under hea ...

  • S&S Cycle Motorcycle Accessories - page 12

    9. Compression releases and rocker cover installation. Refer to the included instructions to install the compression releases and rocker covers NOTES: ● If S&S compression releases will be installed, it is much easier to install them before the rocker covers are installed and the engine is installed in the frame. S&S die-cast T win Cam st ...

  • S&S Cycle Motorcycle Accessories - page 13

    H. Fuel system installation and tuning NOTES - S&S Engine assemblies are available with either carbureted or fuel injected systems. Assembled Engines are shipped with the carburetor or fuel injection system installed. Refer to the included instructions for operation and tuning . Unassembled Engines are shipped with the fuel system packaged sepa ...

  • S&S Cycle Motorcycle Accessories - page 14

    NOTE - S&S oil line, oil tank fittings, and oil conduit block fittings have a larger diameter than OEM components. CAUTION - Do not use the existing OEM oil tank fittings with S&S oil line #50-8157. The OEM fittings are not large enough diameter for the S&S oil line. NOTES: ● lnstallations must use supplied S&S oil tank fittings i ...

  • S&S Cycle Motorcycle Accessories - page 15

    NOTES: ● If oil fails to appear at oil sender hole within 30 seconds of starter operation, allow the starter to cool. verify that oil line routing is correct and that the oil tank is full to the proper level ● Oil pressure indicator lamp should light when ignition is turned on. Lamp will go out after engine is started and there is oil pressure ...

  • S&S Cycle Motorcycle Accessories - page 16

    2. Engine break-in 1. Closely monitor engine for excessive heat build-up. Do not allow the engine to idle for long periods of time. Be especially watchful when air temperatures exceed 90 degrees. Slow speed operation in urban areas during the summertime is especially hard on engines.. T emperature for engine oil should be between 180º - 240º F . ...

  • S&S Cycle Motorcycle Accessories - page 17

    17 Displacement Bore Stroke Compression Ratio 124” 4-1⁄8” 4-5⁄8” 10.8:1 Cylinder Heads Specification V alve guide in head (tight) .0015”-.003” V alve seat in head (tight) .005”-.0075” V alves Specification Service (Fit in guide.) Wear Limit Intake .0012”-.0015” .0025” Exhaust .0018”-.0023” .0035” Seat Width .040”-.06 ...

  • S&S Cycle Motorcycle Accessories - page 18

    18 S&S Recommended Regular Service Intervals Item Interval Engine Oil & Filter ...........................................Change at 50, 500, 2,500 miles, every 2,500 ........................................................................ miles thereafter . 1 Air Cleaner .......................................................Inspect at 50 a ...

  • S&S Cycle Motorcycle Accessories - page 19

    19 1 2 6 4 5 33 31 18 14 12 11 16 17 12 14 10 7 19 25 27 24 26 13 15 30 29 28 20 25 32 21 23 22 3 9 8 7 1. Bolt, stator 10-24 x1" SHC - 4 required (HD#2720) (10 Pack) . ..................... 50-0194 2. Seal, sprocket shaft (HD#12068) ................................... 31-4035 3. Bearing, T imken (HD#9028) .......... 31-4013 4. Bolt, case 5/16 ...

  • S&S Cycle Motorcycle Accessories - page 20

    Because e v ery industry has a leader ...

Produzent S&S Cycle Kategorie Motorcycle Accessories

Dokumente, die wir vom Produzenten des Geräts S&S Cycle Motorcycle Accessories erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen S&S Cycle
- Bedienungsanleitungen Motorcycle Accessories
- Produktkarten S&S Cycle
- Informationsbroschüren
- oder Energieetiketten S&S Cycle Motorcycle Accessories
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung S&S Cycle Motorcycle Accessories.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen S&S Cycle Motorcycle Accessories, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen S&S Cycle Motorcycle Accessories. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts S&S Cycle Motorcycle Accessories ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts S&S Cycle Motorcycle Accessories, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von S&S Cycle Motorcycle Accessories hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von S&S Cycle Motorcycle Accessories verständlich ist.

Eine gänzliche Bedienungsanleitung von S&S Cycle sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von S&S Cycle Motorcycle Accessories bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von S&S Cycle Motorcycle Accessories befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich S&S Cycle Motorcycle Accessories, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts S&S Cycle Motorcycle Accessories - die uns die ersten Schritte während der Nutzung von S&S Cycle Motorcycle Accessories erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit S&S Cycle Motorcycle Accessories hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von S&S Cycle Motorcycle Accessories im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich S&S Cycle Motorcycle Accessories?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit S&S Cycle Motorcycle Accessories nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit S&S Cycle Motorcycle Accessories hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)