Italiano dropdown-ico

Manuale per l’uso S&S Cycle Motorcycle Accessories

20 pagine 0.3 mb
Scarica

Vai alla pagina of 20

Summary
  • S&S Cycle Motorcycle Accessories - page 1

    1 Instruction Sheet #51-1 160 04-28-04 Copyright®, 2003 by S&S Cycle, Inc. All rights reserved. Printed in the U.S.A. Because e v ery industry has a leader S&S T win Cam Style Engine Assembly and Installation Instructions S & S Cycle , I nc. 14025 County Highway G Box 215 V iola, W isconsin 54664 Phone: 608-627-2080 • Fax: 608-627-14 ...

  • S&S Cycle Motorcycle Accessories - page 2

    2 SAFE INST ALLA TION AND OPERA TION RULES: Before installing any S&S engine part, it is your responsibility to read and follow all instructions. The rules below are for your personal safety , and must be kept in mind at all times. ● Gasoline is extremely flammable and explosive under certain conditions, and toxic when inhaled. Do not smoke a ...

  • S&S Cycle Motorcycle Accessories - page 3

    S&S Basic T win Cam Style Engines for Evolution Style Chassis * Displacement Bore Stroke Fuel System Finish Assembled Part Number Natural 31-9340 124" 4 1 ⁄ 8 "4 5 ⁄ 8 " Carburetor 1 Black 31-9341 Natural 31-9343 124" 4 1 ⁄ 8 "4 5 ⁄ 8 " S&S VFI 2 Black 31-9344 S&S Basic T win Cam Style Engines f o r ...

  • S&S Cycle Motorcycle Accessories - page 4

    B. Additional Features: ● Greater overall strength than stock crankcases, especially in the front motor mount, an important consideration in high performance applications. ● All oil passages between the crankcase and cam support plate are o-ring sealed. ● Compatible with stock components. Use stock oil pump, cam support plate, gear cover , et ...

  • S&S Cycle Motorcycle Accessories - page 5

    5 C. Modification Notes S&S Cycle cautions against modifying these crankcases due to the possibility of damaging or weakening them. Modifying S&S crankcases in any fashion voids all manufacturer warranties. Should the customer elect to modify the crankcases regardless, it is imperative that they and the information tag attached to them be i ...

  • S&S Cycle Motorcycle Accessories - page 6

    6 CAUTION - Improper alignment of engine and frame mounts may cause abnormal stresses resulting in damage to crankcases or other parts. 2. T est-fit instructions for T win Cam style cases with Evo Style motor mounts. 1. Assemble case halves using case bolts. T ighten to snug. T orquing bolts to final specification is not necessary . 2. Clean frame ...

  • S&S Cycle Motorcycle Accessories - page 7

    CAUTION - Failure to observe the above may result in engine damage not covered under warranty . 1. Crankcase preparation before assembly . NOTES - S&S crankcases are sold in matched sets only . Individual case halves are not available. S&S T win Cam style engines are shipped with cylinder studs installed Before assembling engine, verify tha ...

  • S&S Cycle Motorcycle Accessories - page 8

    3. Coat right main bearing and race with assembly lube. , then join left and right crankcase halves. 4. T ighten 5⁄16" case bolts to 18 ft-lbs, tighten 1⁄4" center bolt to 120 in-lbs. in the sequence shown. See Figure 1. 5. Install drive sprocket spacer and sprocket shaft oil seal in main bearing race of left case. Spring side of seal ...

  • S&S Cycle Motorcycle Accessories - page 9

    9 Use tool to guide bearing rollers onto inner race Picture E9 Picture E12 Picture E10 Picture E13 Picture E1 1 Figure 1 Picture E7 1 2 3 4 5 6 7 8 9 Picture E8 ...

  • S&S Cycle Motorcycle Accessories - page 10

    10 2. Inspect pistons, especially areas around machined surfaces such as ring grooves and wristpin holes. De-burr as necessary , taking care to remove particles that could become dislodged inside engine. 3. Measure ring end gaps and adjust as necessary . See Pictures E13 and E14 a. Compression ring end-gaps should be between .017” to .025”. b. ...

  • S&S Cycle Motorcycle Accessories - page 11

    11 5. Install cylinder heads 1. Place head gasket on top of cylinder . Locate on dowels installed in cylinder . NOTE - Head gaskets should be installed clean and dry . 2. Before installing heads spin each head bolt down on its respective stud to be sure threads are clean and free of contamination. Place a drop or two of oil on threads and under hea ...

  • S&S Cycle Motorcycle Accessories - page 12

    9. Compression releases and rocker cover installation. Refer to the included instructions to install the compression releases and rocker covers NOTES: ● If S&S compression releases will be installed, it is much easier to install them before the rocker covers are installed and the engine is installed in the frame. S&S die-cast T win Cam st ...

  • S&S Cycle Motorcycle Accessories - page 13

    H. Fuel system installation and tuning NOTES - S&S Engine assemblies are available with either carbureted or fuel injected systems. Assembled Engines are shipped with the carburetor or fuel injection system installed. Refer to the included instructions for operation and tuning . Unassembled Engines are shipped with the fuel system packaged sepa ...

  • S&S Cycle Motorcycle Accessories - page 14

    NOTE - S&S oil line, oil tank fittings, and oil conduit block fittings have a larger diameter than OEM components. CAUTION - Do not use the existing OEM oil tank fittings with S&S oil line #50-8157. The OEM fittings are not large enough diameter for the S&S oil line. NOTES: ● lnstallations must use supplied S&S oil tank fittings i ...

  • S&S Cycle Motorcycle Accessories - page 15

    NOTES: ● If oil fails to appear at oil sender hole within 30 seconds of starter operation, allow the starter to cool. verify that oil line routing is correct and that the oil tank is full to the proper level ● Oil pressure indicator lamp should light when ignition is turned on. Lamp will go out after engine is started and there is oil pressure ...

  • S&S Cycle Motorcycle Accessories - page 16

    2. Engine break-in 1. Closely monitor engine for excessive heat build-up. Do not allow the engine to idle for long periods of time. Be especially watchful when air temperatures exceed 90 degrees. Slow speed operation in urban areas during the summertime is especially hard on engines.. T emperature for engine oil should be between 180º - 240º F . ...

  • S&S Cycle Motorcycle Accessories - page 17

    17 Displacement Bore Stroke Compression Ratio 124” 4-1⁄8” 4-5⁄8” 10.8:1 Cylinder Heads Specification V alve guide in head (tight) .0015”-.003” V alve seat in head (tight) .005”-.0075” V alves Specification Service (Fit in guide.) Wear Limit Intake .0012”-.0015” .0025” Exhaust .0018”-.0023” .0035” Seat Width .040”-.06 ...

  • S&S Cycle Motorcycle Accessories - page 18

    18 S&S Recommended Regular Service Intervals Item Interval Engine Oil & Filter ...........................................Change at 50, 500, 2,500 miles, every 2,500 ........................................................................ miles thereafter . 1 Air Cleaner .......................................................Inspect at 50 a ...

  • S&S Cycle Motorcycle Accessories - page 19

    19 1 2 6 4 5 33 31 18 14 12 11 16 17 12 14 10 7 19 25 27 24 26 13 15 30 29 28 20 25 32 21 23 22 3 9 8 7 1. Bolt, stator 10-24 x1" SHC - 4 required (HD#2720) (10 Pack) . ..................... 50-0194 2. Seal, sprocket shaft (HD#12068) ................................... 31-4035 3. Bearing, T imken (HD#9028) .......... 31-4013 4. Bolt, case 5/16 ...

  • S&S Cycle Motorcycle Accessories - page 20

    Because e v ery industry has a leader ...

Fabbricante S&S Cycle Categoria Motorcycle Accessories

I documenti che otteniamo dal fabbricante del dispositivoS&S Cycle Motorcycle Accessories possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici S&S Cycle
- manuali per l’uso Motorcycle Accessories
- schede prodotto S&S Cycle
- opuscoli
- o etichette energetiche S&S Cycle Motorcycle Accessories
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso S&S Cycle Motorcycle Accessories.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione S&S Cycle Motorcycle Accessories, manuali di manutenzione, brevi manuali o manuali utente S&S Cycle Motorcycle Accessories. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto S&S Cycle Motorcycle Accessories.

Manuali per l’uso simili

Manuale completo del dispositivo S&S Cycle Motorcycle Accessories, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare S&S Cycle Motorcycle Accessories dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti S&S Cycle Motorcycle Accessories.

Il manuale per l’uso completo S&S Cycle, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale S&S Cycle Motorcycle Accessories - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice S&S Cycle Motorcycle Accessories, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per S&S Cycle Motorcycle Accessories che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo S&S Cycle Motorcycle Accessories - che ci dovrebbe aiutare nei primi passi durante l'uso S&S Cycle Motorcycle Accessories
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del S&S Cycle Motorcycle Accessories
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio S&S Cycle Motorcycle Accessories in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su S&S Cycle Motorcycle Accessories?

Utilizza il modulo sottostante

Se non hai risolto il problema con S&S Cycle Motorcycle Accessories con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con S&S Cycle Motorcycle Accessories è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)