Bedienungsanleitung Delta TP400LS

21 Seiten 0.72 mb
Download

Zur Seite of 21

Summary
  • Delta TP400LS - page 1

    INSTRUCTION MANUAL 12½" Portable Planer (Model TP400LS) P ART NO. A02473 - 04-06-04 Copyright © 2004 Delta Machinery ESP AÑOL: PÁGINA 21 T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582). ...

  • Delta TP400LS - page 2

    2 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury . Used without the saf ...

  • Delta TP400LS - page 3

    3 GENERAL SAFETY RULES 1. FOR YOUR OWN SAFETY , READ THE INSTRUCTION MANUAL BEFORE OPERA TING THE MACHINE. Learning the machine’ s application, limitations, and specific hazards will gr eatly minimize the possibility of accidents and injury . 2. WEAR EYE PROTECTION. AL WA YS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is d ...

  • Delta TP400LS - page 4

    4 ADDITIONAL SAFETY RULES FOR PLANERS 1. DO NOT OPERA TE THIS MACHINE until it is completely assembled and installed according to the instructions. A machine incorrectly assembled can cause serious injury . 2. OBT AIN ADVICE from your supervisor , instructor , or another qualified person if you are not thoroughly familiar with the operation of this ...

  • Delta TP400LS - page 5

    5 A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cor ds which have 3- prong gr ounding type plugs and matching receptacle which will accept the machine’ s plug. Before connec ...

  • Delta TP400LS - page 6

    6 EXTENSION CORDS Use proper extension cor ds. Make sure your extension cor d is in good condition and is a 3-wire extension cord which has a 3-pr ong grounding type plug and matching r eceptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the machine. An undersized ...

  • Delta TP400LS - page 7

    7 FOREWORD FUNCTIONAL DESCRIPTION UNP ACKING AND CLEANING Carefully unpack the machine and all loose items fr om the shipping container . Peel protective film fr om the table surface. Figures 1 and 2 illustrate the planer and all loose items supplied with your machine. Refer to the section of this manual entitled “REPLACING KNIVES” and remove t ...

  • Delta TP400LS - page 8

    FOR YOUR OWN SAFETY , DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETEL Y ASSEMBLED AND YOU READ AND UNDERST AND THE ENTIRE INSTRUCTION MANUAL. 8 PLANER P AR TS 1 - 12½" Portable Planer 2 - Cutterhead raising and lowering handle 3 - M5x.8x20mm hex socket head screw 4 - Cutterhead lock handle 5 - M6x20mm specia hex ...

  • Delta TP400LS - page 9

    9 Fig. 4 Fig. 5 Fig. 6 A A A B C A LOWERING EXTENSION T ABLES The infeed and outfeed table extensions (A) Fig. 4, are shipped attached to the machine in the “UP” position. Rotate both table extensions to the down position as shown. The top surface of the table extensions should be level with the planer table. T o check and adjust if necessary , ...

  • Delta TP400LS - page 10

    10 F ASTENING PLANER TO ST AND 2. Fasten cutterhead raising and lowering handle (A) Fig. 8, to shaft using the M5x.8x20mm hex socket head screw (C) with wr ench supplied. 3. Rotate handle (A) to the operating position as shown in Fig. 9, and tighten set screw (D). Place the planer on the stand and align the four holes in the base of the machine, tw ...

  • Delta TP400LS - page 11

    11 ST AR TING AND STOPPING PLANER The on/off switch (A) Fig. 14, is located on the front of the planer motor . T o tur n the machine “ON” move the switch up to the “ON” position. T o tur n the machine “OFF” move the switch down to the “OFF” position. LOCKING SWITCH IN THE “OFF” POSITION When the tool is not in use, the switch sh ...

  • Delta TP400LS - page 12

    12 RECOMMENDED DEPTH OF CUT NOTE: One revolution of the raising and lowering handle will move the cutterhead up or down 3/32 of an inch. A 3/32" depth of cut can be made in soft woods on stock up to 8" wide and in hard woods on stock up to 7" wide; see chart in Fig. 18. For 10" and 12" wide soft wood, we recommend a maxi- m ...

  • Delta TP400LS - page 13

    13 KNIFE TRANSFER TOOL STORAGE 1. The knife transfer tool (A) Fig. 20, supplied with your planer , can easily be stored underneath the outfeed table extension (B) when not being used. A V elcro strip (C) is provided on the tool and underneath the table for this purpose. 2. Figure 21 illustrates the knife transfer tool (A) stored underneath the outf ...

  • Delta TP400LS - page 14

    14 Fig. 22 Fig. 23 CARR YING HANDLE/STOCK TRANSFER BAR 1. Y our planer is provided with a foam covered carrying handle (A) Fig. 22, located on top of the machine, for ease in transporting the planer . Carrying handles are also pr ovided at the base of the planer on each side which allow you to lift the machine with ease . 2. The carrying handle (A) ...

  • Delta TP400LS - page 15

    15 5. Figure 26 illustrates the cutterhead (C) locked in place allowing access to the knife locking bar (E). 6. Using the supplied wrench (E) Fig. 27, unscrew the six screws, five of which ar e shown at (F), only enough until locking bar (D) separates from knife, allowing knife to be removed. 7. Insert knife transfer tool (G) Fig. 28, under neath c ...

  • Delta TP400LS - page 16

    16 9. Remove knife transfer tool and tighten the six screws, five of which ar e shown at (F) Fig. 30, using wrench (E) supplied. 10. Replace other knife by rotating head 180 degr ees and repeat STEPS 5 THROUGH 10. 11. Replace cutterhead guard (B) Fig. 31, making sure cutterhead lock (D) is depressed and underneath guard as shown. Slide guard in as ...

  • Delta TP400LS - page 17

    17 Fig. 34 Fig. 35 2. Make sure the knives ar e inserted into the cutterhead properly , as explained under “REPLACING KNIVES.” 3. Place the gage block (A) Fig. 34, on the table, over a 0.020" feeler gage and position the gage block (A) dir ectly underneath the cutterhead. Raise or lower the head assembly and rotate the cutterhead, by follo ...

  • Delta TP400LS - page 18

    18 MAINTENANCE BRUSH INSPECTION AND REPLACEMENT DIS CONNECT MACHINE FROM POWER SOURCE. Brush life varies. It depends on the load on the motor . Check the brushes after the first 50 hours of use for a new machine or after a new set of brushes has been installed. After the first check, examine them after about every 10 hours of use until replacement ...

  • Delta TP400LS - page 19

    19 NOTES ...

  • Delta TP400LS - page 20

    20 A complete line of accessories is available from your Delta Supplier , Porter -Cable • Delta Factory Service Centers, and Delta Authorized Service Stations. Please visit our W eb Site www .deltamachinery .com for a catalog or for the name of your nearest supplier . Since accessories other than those offer ed by Delta have not been tested with ...

  • Delta TP400LS - page 21

    The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas r egistradas de PORTER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL T ...

Produzent Delta Kategorie Planer

Dokumente, die wir vom Produzenten des Geräts Delta TP400LS erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Delta
- Bedienungsanleitungen TP400LS
- Produktkarten Delta
- Informationsbroschüren
- oder Energieetiketten Delta TP400LS
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Delta TP400LS.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Delta TP400LS, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Delta TP400LS. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Delta TP400LS ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Delta TP400LS, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Delta TP400LS hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Delta TP400LS verständlich ist.

Eine gänzliche Bedienungsanleitung von Delta sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Delta TP400LS bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Delta TP400LS befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Delta TP400LS, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Delta TP400LS - die uns die ersten Schritte während der Nutzung von Delta TP400LS erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Delta TP400LS hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Delta TP400LS im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Delta TP400LS?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Delta TP400LS nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Delta TP400LS hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)