Delta TP400LSの取扱説明書

21ページ 0.72 mb
ダウンロード

ページに移動 of 21

Summary
  • Delta TP400LS - page 1

    INSTRUCTION MANUAL 12½" Portable Planer (Model TP400LS) P ART NO. A02473 - 04-06-04 Copyright © 2004 Delta Machinery ESP AÑOL: PÁGINA 21 T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582). ...

  • Delta TP400LS - page 2

    2 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury . Used without the saf ...

  • Delta TP400LS - page 3

    3 GENERAL SAFETY RULES 1. FOR YOUR OWN SAFETY , READ THE INSTRUCTION MANUAL BEFORE OPERA TING THE MACHINE. Learning the machine’ s application, limitations, and specific hazards will gr eatly minimize the possibility of accidents and injury . 2. WEAR EYE PROTECTION. AL WA YS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is d ...

  • Delta TP400LS - page 4

    4 ADDITIONAL SAFETY RULES FOR PLANERS 1. DO NOT OPERA TE THIS MACHINE until it is completely assembled and installed according to the instructions. A machine incorrectly assembled can cause serious injury . 2. OBT AIN ADVICE from your supervisor , instructor , or another qualified person if you are not thoroughly familiar with the operation of this ...

  • Delta TP400LS - page 5

    5 A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cor ds which have 3- prong gr ounding type plugs and matching receptacle which will accept the machine’ s plug. Before connec ...

  • Delta TP400LS - page 6

    6 EXTENSION CORDS Use proper extension cor ds. Make sure your extension cor d is in good condition and is a 3-wire extension cord which has a 3-pr ong grounding type plug and matching r eceptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the machine. An undersized ...

  • Delta TP400LS - page 7

    7 FOREWORD FUNCTIONAL DESCRIPTION UNP ACKING AND CLEANING Carefully unpack the machine and all loose items fr om the shipping container . Peel protective film fr om the table surface. Figures 1 and 2 illustrate the planer and all loose items supplied with your machine. Refer to the section of this manual entitled “REPLACING KNIVES” and remove t ...

  • Delta TP400LS - page 8

    FOR YOUR OWN SAFETY , DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETEL Y ASSEMBLED AND YOU READ AND UNDERST AND THE ENTIRE INSTRUCTION MANUAL. 8 PLANER P AR TS 1 - 12½" Portable Planer 2 - Cutterhead raising and lowering handle 3 - M5x.8x20mm hex socket head screw 4 - Cutterhead lock handle 5 - M6x20mm specia hex ...

  • Delta TP400LS - page 9

    9 Fig. 4 Fig. 5 Fig. 6 A A A B C A LOWERING EXTENSION T ABLES The infeed and outfeed table extensions (A) Fig. 4, are shipped attached to the machine in the “UP” position. Rotate both table extensions to the down position as shown. The top surface of the table extensions should be level with the planer table. T o check and adjust if necessary , ...

  • Delta TP400LS - page 10

    10 F ASTENING PLANER TO ST AND 2. Fasten cutterhead raising and lowering handle (A) Fig. 8, to shaft using the M5x.8x20mm hex socket head screw (C) with wr ench supplied. 3. Rotate handle (A) to the operating position as shown in Fig. 9, and tighten set screw (D). Place the planer on the stand and align the four holes in the base of the machine, tw ...

  • Delta TP400LS - page 11

    11 ST AR TING AND STOPPING PLANER The on/off switch (A) Fig. 14, is located on the front of the planer motor . T o tur n the machine “ON” move the switch up to the “ON” position. T o tur n the machine “OFF” move the switch down to the “OFF” position. LOCKING SWITCH IN THE “OFF” POSITION When the tool is not in use, the switch sh ...

  • Delta TP400LS - page 12

    12 RECOMMENDED DEPTH OF CUT NOTE: One revolution of the raising and lowering handle will move the cutterhead up or down 3/32 of an inch. A 3/32" depth of cut can be made in soft woods on stock up to 8" wide and in hard woods on stock up to 7" wide; see chart in Fig. 18. For 10" and 12" wide soft wood, we recommend a maxi- m ...

  • Delta TP400LS - page 13

    13 KNIFE TRANSFER TOOL STORAGE 1. The knife transfer tool (A) Fig. 20, supplied with your planer , can easily be stored underneath the outfeed table extension (B) when not being used. A V elcro strip (C) is provided on the tool and underneath the table for this purpose. 2. Figure 21 illustrates the knife transfer tool (A) stored underneath the outf ...

  • Delta TP400LS - page 14

    14 Fig. 22 Fig. 23 CARR YING HANDLE/STOCK TRANSFER BAR 1. Y our planer is provided with a foam covered carrying handle (A) Fig. 22, located on top of the machine, for ease in transporting the planer . Carrying handles are also pr ovided at the base of the planer on each side which allow you to lift the machine with ease . 2. The carrying handle (A) ...

  • Delta TP400LS - page 15

    15 5. Figure 26 illustrates the cutterhead (C) locked in place allowing access to the knife locking bar (E). 6. Using the supplied wrench (E) Fig. 27, unscrew the six screws, five of which ar e shown at (F), only enough until locking bar (D) separates from knife, allowing knife to be removed. 7. Insert knife transfer tool (G) Fig. 28, under neath c ...

  • Delta TP400LS - page 16

    16 9. Remove knife transfer tool and tighten the six screws, five of which ar e shown at (F) Fig. 30, using wrench (E) supplied. 10. Replace other knife by rotating head 180 degr ees and repeat STEPS 5 THROUGH 10. 11. Replace cutterhead guard (B) Fig. 31, making sure cutterhead lock (D) is depressed and underneath guard as shown. Slide guard in as ...

  • Delta TP400LS - page 17

    17 Fig. 34 Fig. 35 2. Make sure the knives ar e inserted into the cutterhead properly , as explained under “REPLACING KNIVES.” 3. Place the gage block (A) Fig. 34, on the table, over a 0.020" feeler gage and position the gage block (A) dir ectly underneath the cutterhead. Raise or lower the head assembly and rotate the cutterhead, by follo ...

  • Delta TP400LS - page 18

    18 MAINTENANCE BRUSH INSPECTION AND REPLACEMENT DIS CONNECT MACHINE FROM POWER SOURCE. Brush life varies. It depends on the load on the motor . Check the brushes after the first 50 hours of use for a new machine or after a new set of brushes has been installed. After the first check, examine them after about every 10 hours of use until replacement ...

  • Delta TP400LS - page 19

    19 NOTES ...

  • Delta TP400LS - page 20

    20 A complete line of accessories is available from your Delta Supplier , Porter -Cable • Delta Factory Service Centers, and Delta Authorized Service Stations. Please visit our W eb Site www .deltamachinery .com for a catalog or for the name of your nearest supplier . Since accessories other than those offer ed by Delta have not been tested with ...

  • Delta TP400LS - page 21

    The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas r egistradas de PORTER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL T ...

メーカー Delta カテゴリー Planer

Delta TP400LSのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- TP400LSの取扱説明書
- Deltaの製品カード
- パンフレット
- またはDelta TP400LSの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Delta TP400LSの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Delta TP400LSの取り付け説明書、サービスマニュアル、簡易説明書、またはDelta TP400LSのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Delta TP400LSの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Delta TP400LSデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがDelta TP400LSを使用するのを助ける技術的文書のことです。説明書は通常、全てのDelta TP400LSユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Deltaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Delta TP400LSの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははDelta TP400LSの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Delta TP400LSに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Delta TP400LSデバイスの基本機能を使うにあたってのヒント。 Delta TP400LSのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Delta TP400LSに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるDelta TP400LSのメーカー/サービスへの連絡先に関する情報。

Delta TP400LSについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもDelta TP400LSの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがDelta TP400LSで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)