Bedienungsanleitung Baldor BSC 7107 DC

18 Seiten 0.13 mb
Download

Zur Seite of 18

Summary
  • Baldor BSC 7107 DC - page 1

    BSC 7107 DC Brushless Control Installation and Operating Manual 9/97 MN1231 ...

  • Baldor BSC 7107 DC - page 2

    T able of Contents T able of Contents i Section 1 General Information 1-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Introduction 1-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Limited W arranty 1-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety Notice 1-3 . . . . . . . . . . . . ...

  • Baldor BSC 7107 DC - page 3

    ii T able of Contents ...

  • Baldor BSC 7107 DC - page 4

    Section 1 General Information General Information 1-1 Introduction Baldor Series BSC 7107 control is a general purpose brushless DC motor control. This control commutates power into standard 3-phase brushless (BLDC) motors. The control input line voltage is 120 V AC ± 10%. This control provides up to 7 amperes of continuous current to the motor . ...

  • Baldor BSC 7107 DC - page 5

    1-2 General Information Limited W arranty Fo r a period of one (1) year from the date of original purchase, BALDOR will repair or replace without charge controls and accessories which our examination proves to be defective in material or workmanship. This warranty is valid if the unit has not been tampered with by unauthorized persons, misused, abu ...

  • Baldor BSC 7107 DC - page 6

    General Information 1-3 Safety Notice This equipment contains voltages that may be as great as 1000 volts! Electrical shock can cause serious or fatal injury . Only qualified personnel should attempt the start-up procedure or troubleshoot this equipment. This equipment may be connected to other machines that have rotating parts or parts that are dr ...

  • Baldor BSC 7107 DC - page 7

    1-4 General Information W ARNING: Be sure the system is properly grounded before applying power . Do not apply AC power before you ensure that all grounding instructions have been followed. Electrical shock can cause serious or fatal injury . W ARNING: Do not remove cover for at least five (5) minutes after AC power is disconnected to allow capacit ...

  • Baldor BSC 7107 DC - page 8

    Section 2 Receiving & Installation Receiving & Installation 2-1 Receiving The control is thoroughly tested at the factory and carefully packaged for shipment. When you receive your control, there are several things you should do immediately . 1. Observe the condition of the shipping container and report any damage immediately to the commerc ...

  • Baldor BSC 7107 DC - page 9

    2-2 Receiving & Installation Figure 2-1 Mounting Diagram 6.70 9.00 7.50 6.30 0.20 7 / 32 dia. (4 places) 2.90 T op View End V iew AC Power Connection Refer to Figure 2-2. A fused 120 V AC power source is required. A 12 AMP fuse should be used. 1. Be sure the AC source is disconnected (OFF). 2. Be sure the appropriate fuse is installed at the so ...

  • Baldor BSC 7107 DC - page 10

    Receiving & Installation 2-3 Figure 2-2 Control Connection Locations P4 Upper Board P1 GND (Connect to plant “Earth” ground). AC Line BLDC Motor Connection s. Scaled motor current test point. 1 10mV = 1A Motor Current. 60 ° / 120 ° Jumper 120 ° 60 ° Lower Board T erminal tightening torque = 4 Lb-in (0.45 Nm) (Black) (Red) + Hall 10K 10K ...

  • Baldor BSC 7107 DC - page 11

    2-4 Receiving & Installation Sensor and Motor Connections Refer to Figure 2-2. Brushless DC motors have eleven (1 1) wires: three (3) motor phase power wires, three (3) hall sensor wires, two (2) wires for hall sensor power and sensor common, one (1) wire for motor ground and two (2) wires for motor thermal switch. Note: Baldor BLDC motors have ...

  • Baldor BSC 7107 DC - page 12

    Receiving & Installation 2-5 Reverse Operation T erminal P4–REV is the forward/reverse control. Y ou can reverse motor direction by connecting P4–REV to P4–COM. Use a jumper wire, switch, relay , or an open collector NPN transistor . Caution: Before reversing directions, make sure the motor is stopped. This control is not designed for plu ...

  • Baldor BSC 7107 DC - page 13

    2-6 Receiving & Installation 1st Time Power Up Procedure (or after a motor is replaced) Caution: If full AC V oltage is applied and the motor connections are wrong, the control will be damaged. Apply 10% of the input voltage to test motor lead connections at the first time power up or after a motor is replaced. It is strongly recommended that a ...

  • Baldor BSC 7107 DC - page 14

    Section 3 Adjustments Adjustments 3-1 Current Limit Adjustment The current limit adjustment is factory set at 10 AMPS and you should not have to increase this setting for the Series BSC 7107 control. Rotating the I Limit potentiometer on the upper board CCW decreases the current limit. T o calculate motor current, refer to Figure 2-2 and measure th ...

  • Baldor BSC 7107 DC - page 15

    3-2 Adjustments Minimum Speed Adjustment 1. Set the Speed Pot to zero speed (fully CCW). 2. Set the MIN pot on the upper board (Figure 2-2) fully CCW . 3. Apply power to the control. 4. Slowly rotate the MIN CW until the motor begins to rotate. Then turn the pot CCW until the motor just stops. The control will now run with a near–zero deadband. 5 ...

  • Baldor BSC 7107 DC - page 16

    Section 4 Specifications and Data Specifications 4-1 Specifications Input V oltage 120 V AC ± 10% . . . . . . . . . . . . . . . . . . . . . Output V oltage (Filtered Output) 0 to 140 VDC . . . . . Load Current (Continuous) 7 Amperes . . . . . . . . . . . . . Overload Current 150% for 30 seconds . . . . . . . . . . . . . Speed Range 50:1 . . . . . ...

  • Baldor BSC 7107 DC - page 17

    4-2 Specifications Hall Signal Timing Diagram S1 (White) S2 (Y ellow) S3 (Orange) 0 0 0 15 30 60 30 60 120 45 60 90 60 120 240 75 150 300 90 180 360 105 210 420 120 240 480 135 270 540 150 300 600 165 330 660 180 360 720 Ć 8 Pole Mechanical Degrees Ć 4 Pole Mechanical Degrees Ć Electrical Degrees Hall Sensor Leads ( Hall generated signal) Brushl ...

  • Baldor BSC 7107 DC - page 18

    BALDOR ELECTRIC COMP ANY P .O. Box 2400 Fort Smith, AR 72902–2400 (479) 646–471 1 Fax (479) 648–5792 © Baldor Electric Company Printed in USA MN1231 9/97 PS50 ...

Produzent Baldor Kategorie Outboard Motor

Dokumente, die wir vom Produzenten des Geräts Baldor BSC 7107 DC erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Baldor
- Bedienungsanleitungen BSC 7107 DC
- Produktkarten Baldor
- Informationsbroschüren
- oder Energieetiketten Baldor BSC 7107 DC
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Baldor BSC 7107 DC.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Baldor BSC 7107 DC, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Baldor BSC 7107 DC. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Baldor BSC 7107 DC ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Baldor BSC 7107 DC, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Baldor BSC 7107 DC hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Baldor BSC 7107 DC verständlich ist.

Eine gänzliche Bedienungsanleitung von Baldor sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Baldor BSC 7107 DC bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Baldor BSC 7107 DC befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Baldor BSC 7107 DC, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Baldor BSC 7107 DC - die uns die ersten Schritte während der Nutzung von Baldor BSC 7107 DC erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Baldor BSC 7107 DC hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Baldor BSC 7107 DC im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Baldor BSC 7107 DC?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Baldor BSC 7107 DC nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Baldor BSC 7107 DC hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)