Bedienungsanleitung Cisco Network Switch Cabling

18 Seiten 0.26 mb
Download

Zur Seite of 18

Summary
  • Cisco Network Switch Cabling - page 1

    C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 16 Control Node and Network Switch Cabling Example This docume nt provides background infor mation and detailed procedures for cab ling dual Cassatt Active R esponse control nodes a nd netw o rk switches and for configuring those netw ork switches . These pr ocedures a ...

  • Cisco Network Switch Cabling - page 2

    C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 17 application nodes . Note that detailed instr uct ions for adding application nodes are in a separate documen t, which yo u should consult wh en you are ready to cable application nodes into your Cassatt Acti ve R esp onse environment. (Figure 1 hi ghlights the contr ...

  • Cisco Network Switch Cabling - page 3

    C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 18 T able 1 shows ho w each por t is used on the switc h and control node . T able 1 Description of Panel and Main Board Not ation Not a tion Description ISL-1 Used to create the first half of interswitch link (ISL) connection between the tw o Cisco switches . ISL-2 Us ...

  • Cisco Network Switch Cabling - page 4

    C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 19 Racking and cabling guidelines T o cable your control nodes to the network sw itc hes according to Figure 1, follow these steps . Remember that this sample configurat io n uses four netwo rk switches , so use thes e instr uctions as a guideline for your o w n config ...

  • Cisco Network Switch Cabling - page 5

    C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 20 3. Connect the cont rol nodes to the shared sto rage hardware, as follows: 4. Using crossov er cables , create an inters witch link (ISL) betw een the two Cisco 3750 switches . The recommended configuration us es two ISL connections between the Cisco switches for in ...

  • Cisco Network Switch Cabling - page 6

    C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 21 Configuring the switches After you hav e racked and cabled the control nodes and sw itches , you need to configure both Cisco switch stac ks . If you are using another of the Cassatt recommend ed switches (see the Info Central site for recommended switch hardw are), ...

  • Cisco Network Switch Cabling - page 7

    C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 22 4. Plug in the Cisco switches in a stac k. 5. Many boot-up and self-test messages will scroll on the console monitor . When the process is completed, use the following table to deter mine your next ste p: Restoring the factory default settings T o reset the switc he ...

  • Cisco Network Switch Cabling - page 8

    C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 23 3. If the switch w a s used previously in a switch stack, and is no w in a diff erent switch stack, it may ha ve a switch n umber other than 1 and 2. T o deter mine if the switch number must be reset, display the switc h configuration as follows: Current Switch# Rol ...

  • Cisco Network Switch Cabling - page 9

    C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 24 Changing Switch Number 3 to Switch Number 2 New Switch Number will be effective after next reboot 6. Exit the configuration mode, as follo ws : 7. Halt and perfor m a cold restar t, as follows: 00:08:23: %SYS-5-RELOAD: Reload requested Base ethernet MAC Address: 00: ...

  • Cisco Network Switch Cabling - page 10

    C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 25 2. Enter the privileged mode, as follows: 3. Enter the configuration mode, as follo ws: Enter configuration commands, one per line. End with CNTL/Z. 4. T urn the messag es off, as follows: 5. T ur n off all interfaces on the first switch, as follows: 6. T urn off al ...

  • Cisco Network Switch Cabling - page 11

    C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 26 7. Set the host name of the switc h stack, as follo ws: 8. Set the switch stac k’ s enable password, as follo ws: 9. T ur n off the VLAN tr unking protoc ol (VTP), as follows: sw01(config)# Setting device to VTP TRANSPARENT mode. 10. Enable the portfast bpduguard ...

  • Cisco Network Switch Cabling - page 12

    C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 27 11. Ag g reg ate the tw o physical links betw een the two Cisco switches in the stac k into a single logical link, as follows: Creating a port-channel interface Port-channel 1 12. Set the interface co nnection to the ro uter, as follo ws: At this prompt... Enter ... ...

  • Cisco Network Switch Cabling - page 13

    C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 28 13. Set the remaining interfaces , wh ich are identical, as follo ws . %Warning: portfast should only be enabled on ports connected to a single host. Connecting hubs, concentrators, switches, bridges, etc... to this interface when portfast is enabled, can cause temp ...

  • Cisco Network Switch Cabling - page 14

    C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 29 %Portfast will be configured in 23 interfaces due to the range command but will only have effect when the interfaces are in a non-trunking mode 14. Disable IGMP snooping, as follows: 15. T urn off the HTTP ser ver , as follows: 16. Set the message of the day , as fo ...

  • Cisco Network Switch Cabling - page 15

    C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 30 17. T ur n all the interfaces back on, as follo ws: 18. T ur n log ging to the c onsole back on, as follows: 19. Exit the configuration mode, as follo ws: 20. V erify the switch configuration, as follo ws: Building configuration... Current configuration : 3230 bytes ...

  • Cisco Network Switch Cabling - page 16

    C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 31 interface Port-channel1 no ip address ! interface GigabitEthernet1/0/1 no ip address no mdix auto channel-group 1 mode on ! interface GigabitEthernet1/0/2 switchport mode access no ip address no mdix auto ! interface GigabitEthernet1/0/3 switchport mode access no ip ...

  • Cisco Network Switch Cabling - page 17

    C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 32 ! interface GigabitEthernet2/0/3 switchport mode access no ip address no mdix auto spanning-tree portfast ! interface GigabitEthernet2/0/4 switchport mode access no ip address no mdix auto spanning-tree portfast ! interface GigabitEthernet2/0/5 switchport mode acces ...

  • Cisco Network Switch Cabling - page 18

    C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 33 21. Sav e the configuration across a reboot of the switch, as follows: Destination filename [startup-config]? Building configuration... [OK] sw01# 22. Configure the second Cisco switch stack b y re peating step 1 in Connecting the switch to a ter minal ser ver on pa ...

Produzent Cisco Kategorie Switch

Dokumente, die wir vom Produzenten des Geräts Cisco Network Switch Cabling erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Cisco
- Bedienungsanleitungen Network Switch Cabling
- Produktkarten Cisco
- Informationsbroschüren
- oder Energieetiketten Cisco Network Switch Cabling
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Cisco Network Switch Cabling.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Cisco Network Switch Cabling, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Cisco Network Switch Cabling. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Cisco Network Switch Cabling ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Cisco Network Switch Cabling, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Cisco Network Switch Cabling hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Cisco Network Switch Cabling verständlich ist.

Eine gänzliche Bedienungsanleitung von Cisco sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Cisco Network Switch Cabling bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Cisco Network Switch Cabling befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Cisco Network Switch Cabling, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Cisco Network Switch Cabling - die uns die ersten Schritte während der Nutzung von Cisco Network Switch Cabling erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Cisco Network Switch Cabling hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Cisco Network Switch Cabling im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Cisco Network Switch Cabling?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Cisco Network Switch Cabling nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Cisco Network Switch Cabling hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)