-
Cisco Network Switch Cabling - page 1
C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 16 Control Node and Network Switch Cabling Example This docume nt provides background infor mation and detailed procedures for cab ling dual Cassatt Active R esponse control nodes a nd netw o rk switches and for configuring those netw ork switches . These pr ocedures a ...
-
Cisco Network Switch Cabling - page 2
C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 17 application nodes . Note that detailed instr uct ions for adding application nodes are in a separate documen t, which yo u should consult wh en you are ready to cable application nodes into your Cassatt Acti ve R esp onse environment. (Figure 1 hi ghlights the contr ...
-
Cisco Network Switch Cabling - page 3
C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 18 T able 1 shows ho w each por t is used on the switc h and control node . T able 1 Description of Panel and Main Board Not ation Not a tion Description ISL-1 Used to create the first half of interswitch link (ISL) connection between the tw o Cisco switches . ISL-2 Us ...
-
Cisco Network Switch Cabling - page 4
C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 19 Racking and cabling guidelines T o cable your control nodes to the network sw itc hes according to Figure 1, follow these steps . Remember that this sample configurat io n uses four netwo rk switches , so use thes e instr uctions as a guideline for your o w n config ...
-
Cisco Network Switch Cabling - page 5
C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 20 3. Connect the cont rol nodes to the shared sto rage hardware, as follows: 4. Using crossov er cables , create an inters witch link (ISL) betw een the two Cisco 3750 switches . The recommended configuration us es two ISL connections between the Cisco switches for in ...
-
Cisco Network Switch Cabling - page 6
C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 21 Configuring the switches After you hav e racked and cabled the control nodes and sw itches , you need to configure both Cisco switch stac ks . If you are using another of the Cassatt recommend ed switches (see the Info Central site for recommended switch hardw are), ...
-
Cisco Network Switch Cabling - page 7
C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 22 4. Plug in the Cisco switches in a stac k. 5. Many boot-up and self-test messages will scroll on the console monitor . When the process is completed, use the following table to deter mine your next ste p: Restoring the factory default settings T o reset the switc he ...
-
Cisco Network Switch Cabling - page 8
C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 23 3. If the switch w a s used previously in a switch stack, and is no w in a diff erent switch stack, it may ha ve a switch n umber other than 1 and 2. T o deter mine if the switch number must be reset, display the switc h configuration as follows: Current Switch# Rol ...
-
Cisco Network Switch Cabling - page 9
C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 24 Changing Switch Number 3 to Switch Number 2 New Switch Number will be effective after next reboot 6. Exit the configuration mode, as follo ws : 7. Halt and perfor m a cold restar t, as follows: 00:08:23: %SYS-5-RELOAD: Reload requested Base ethernet MAC Address: 00: ...
-
Cisco Network Switch Cabling - page 10
C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 25 2. Enter the privileged mode, as follows: 3. Enter the configuration mode, as follo ws: Enter configuration commands, one per line. End with CNTL/Z. 4. T urn the messag es off, as follows: 5. T ur n off all interfaces on the first switch, as follows: 6. T urn off al ...
-
Cisco Network Switch Cabling - page 11
C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 26 7. Set the host name of the switc h stack, as follo ws: 8. Set the switch stac k’ s enable password, as follo ws: 9. T ur n off the VLAN tr unking protoc ol (VTP), as follows: sw01(config)# Setting device to VTP TRANSPARENT mode. 10. Enable the portfast bpduguard ...
-
Cisco Network Switch Cabling - page 12
C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 27 11. Ag g reg ate the tw o physical links betw een the two Cisco switches in the stac k into a single logical link, as follows: Creating a port-channel interface Port-channel 1 12. Set the interface co nnection to the ro uter, as follo ws: At this prompt... Enter ... ...
-
Cisco Network Switch Cabling - page 13
C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 28 13. Set the remaining interfaces , wh ich are identical, as follo ws . %Warning: portfast should only be enabled on ports connected to a single host. Connecting hubs, concentrators, switches, bridges, etc... to this interface when portfast is enabled, can cause temp ...
-
Cisco Network Switch Cabling - page 14
C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 29 %Portfast will be configured in 23 interfaces due to the range command but will only have effect when the interfaces are in a non-trunking mode 14. Disable IGMP snooping, as follows: 15. T urn off the HTTP ser ver , as follows: 16. Set the message of the day , as fo ...
-
Cisco Network Switch Cabling - page 15
C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 30 17. T ur n all the interfaces back on, as follo ws: 18. T ur n log ging to the c onsole back on, as follows: 19. Exit the configuration mode, as follo ws: 20. V erify the switch configuration, as follo ws: Building configuration... Current configuration : 3230 bytes ...
-
Cisco Network Switch Cabling - page 16
C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 31 interface Port-channel1 no ip address ! interface GigabitEthernet1/0/1 no ip address no mdix auto channel-group 1 mode on ! interface GigabitEthernet1/0/2 switchport mode access no ip address no mdix auto ! interface GigabitEthernet1/0/3 switchport mode access no ip ...
-
Cisco Network Switch Cabling - page 17
C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 32 ! interface GigabitEthernet2/0/3 switchport mode access no ip address no mdix auto spanning-tree portfast ! interface GigabitEthernet2/0/4 switchport mode access no ip address no mdix auto spanning-tree portfast ! interface GigabitEthernet2/0/5 switchport mode acces ...
-
Cisco Network Switch Cabling - page 18
C ASSATT A CTIVE R ESPONSE C ONTROL N ODE AND N ETWORK S WITCH C ABLING E XAMPLE 33 21. Sav e the configuration across a reboot of the switch, as follows: Destination filename [startup-config]? Building configuration... [OK] sw01# 22. Configure the second Cisco switch stack b y re peating step 1 in Connecting the switch to a ter minal ser ver on pa ...
¿Tienes una pregunta acerca de Cisco Network Switch Cabling?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Cisco Network Switch Cabling, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Cisco Network Switch Cabling probablemente compartirá una forma de solucionarlo.