-
AT&T 1305 - page 1
Use r ’ s Manual for An s w ering System 1 305 F old open this ma n ual f or in f ormation about this p r oduct ’ s installation and ope r ation . Please r ead Part 1 – Important Product Info r mation, in c luded in this packa g e. Part 2 © 1998 Philips Consumer Communications L. P . All r ights r ese r v ed. P r inted in China . 848230066 I ...
-
AT&T 1305 - page 2
INS T ALL A TION 1 Insert the mic r ocassette. Slide the c o v er down and insert the microcassette with the full reel at the bottom . Replace the co v e r . 1 2 Connect the line cord. Plug the line cord into a modular w all ja c k. 3 Connect a telephone (optional). Plug the line cord f r om the telephone into the TEL SET jack on the ba c k of the ...
-
AT&T 1305 - page 3
OPER A TION 2 Repeat all or part of a message / Reco r d a memo or phone conversation Skip all or part of a message / Reco r d outgoing message Mic r ophone Begin message playback / Stop or pause message playback Dec r ease volume / Erase all or selected messages Reco r ding Y ou r Announcement Be f o r e using this an s w e r ing system , y ou nee ...
-
AT&T 1305 - page 4
2 P r ess and hold A f or t w o seconds , then release the button and w ait f or the system to beep. 3 After the beep , speak to w ard the microphone , f r om about nine in c hes a w a y . 4 P r ess and release p , w hen y ou a r e finished . The tape resets automatical l y and pl a ys the announcement , and the MESS A GE light goes on. T o r eview ...
-
AT&T 1305 - page 5
Priority Call Signal When a caller ente r s the P r io r ity Calling Code f r om a tou c h tone phone , the system beeps loud l y to ale r t y ou that you ha v e a p r iority call . Y ou ’ ll need to provide select calle r s with the P r io r ity Calling Code (p r eset to 1235) in o r der f or them to use this f eature. Y our P r io r ity Calling ...
-
AT&T 1305 - page 6
V olume Cont r ol This system has eight volume le v els ; ea c h time you p r ess the app r op r iate button , the v olume increases or decreases one le v el . T o increase v olume , pr ess and r eleas e + . T o dec r ease volume , press and r elease - . I f y ou ’ r e adjusting the volume while the system is not pl a ying messa g es , y ou ’ l ...
-
AT&T 1305 - page 7
5 If y ou wish , press and releas e f to fast f orwa r d while the memo is pl a ying — OR — P r ess and release to r e wind — OR — P r ess and release p to pause. T w o- W a y Reco r ding Y ou can record a phone con v ersation (the length of the recording depends on the length of y our microcassette) . Y ou can listen to the recording as y ...
-
AT&T 1305 - page 8
When th e T ape is Full When the r ecording side of the tape is complete l y full , the system beeps , the MESS A GE light f lashes r apid l y , and the system tu r ns itself o f f because it cannot r ecord a caller ’ s messa g e . The system an s w e r s calls after 10 r ings and beeps, but does not pl a y an outgoing announcement or r ecord the ...
-
AT&T 1305 - page 9
Remote Acces s Code Y ou can use ma n y f eatures of this an s wering system remote l y from a tou c h tone phone . Most f eatu r es can be accessed only after y ou enter a Remote Access Code . (The preset Remot e Access Code is p r inted on the label on the bottom of the an s wering system.) Connect with th e An s w ering System and Listen to Mess ...
-
AT&T 1305 - page 10
Room Monitor Y ou can call the an s w e r ing system and listen to a n y activity in the r oom f or 15 seconds. 1 Connect with the answering system and listen to messages. 2 P r es s 3 3 . Y ou can listen after the beep. 3 After 15 seconds , the system e xits Room Monitor and beeps twice. T urn System Off 1 Connect with the answering system and lis ...
-
AT&T 1305 - page 11
If this an s w ering system does not wo r k proper l y , t r y the f ollowing sug g estions. If y ou ’ r e still having di f f icult y , call 1 800 722–9125. If the MESSAGE light flashes rapidly: • The tape is full. • No out g oing announcement is r ecorded. If y ou h a v e difficulty hearing messages: The r ecording heads might be soiled a ...
-
AT&T 1305 - page 12
IN C ASE OF DIFFICU L TY If the system does not r espond to r emote commands: • Make su r e y ou a r e calling from a tou c h tone telephone . If y ou hear cli c ks when y ou dial , the phone is not a tou c h tone phone. • There might be noise or inter f erence on the phone line . Press dial buttons f i r m l y . • Make sure y ou are ente r i ...
-
AT&T 1305 - page 13
© 1998 Philips Consumer Communications L. P . All rights reserved. Printed in China. 848230090 Issue 1 A T&T F r om a Remot e T ouc h T one Phone T o connect with your answering system: 1 Dial y our telephone number from a tou c h tone phone. 2 When the system an s w e r s , press * * du r ing the announcement , then enter y our f our-digit Re ...
-
AT&T 1305 - page 14
COMMAND PRESS Rewind 7 7 Fast Forwa r d 9 9 Save all messages Hang up Clear all messages 0 0 Pause/Stop 8 8 Change Remote Access Code 1 1 , enter new code Play/Stop Announcement 4 4 Reco r d/Stop Announcemen t 5 5 Room Monitor 3 3 T u r n system on System tu r ns on after 10 r ings T u r n system o f f 6 6 , then hang up COMMAND PRESS Rewind 7 7 Fa ...
¿Tienes una pregunta acerca de AT&T 1305?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con AT&T 1305, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con AT&T 1305 probablemente compartirá una forma de solucionarlo.