-
Axis Communications Q6044-E - page 1
AXIS Q60 Series AXIS Q6042-E PTZ Dome Network Camera AXIS Q6044-E PTZ Dome Network Camera AXIS Q6045-E PTZ Dome Network Camera E N G L I SH Installation Guide ...
-
Axis Communications Q6044-E - page 2
Legal Considerations Video surveillance can be regulated by laws that vary from country to country . Check the laws in your local region before using this product for surveillance purposes. This product includes one (1) H.264 decoder license. T o purchase further licenses, contact your reseller . Liability Every care has been taken in the preparati ...
-
Axis Communications Q6044-E - page 3
Australia/New Zealand This digital equipment fullls the requirements for RF emission according to the Class A limit of AS/NZS CISPR 22. The product shall be connected using a shielded network cable (STP) that is properly grounded. Notice! This is a Class A product. In a domestic environment this product may cause RF interference, in which case t ...
-
Axis Communications Q6044-E - page 4
...
-
Axis Communications Q6044-E - page 5
AXIS Q60 Series Safety Infor mation Read through this Installation Guide carefully before installing the product. K eep the Installation Guide for future reference. Hazard Levels DANGER Indicates a hazardous situation which, if not avoided, will result in death or serious injury . WARNING Indicates a hazardous situation which, if not avoided, could ...
-
Axis Communications Q6044-E - page 6
AXIS Q60 Series Safety Instructions WARNING • The Axis product shall be installed by a trained professional. NO NO NO TICE TICE TICE • The Axis product shall be used in compliance with local laws and regulations. • Store the Axis product in a dry and ventilated environment. • Avoid exposing the Axis product to shocks or heavy pressure. • ...
-
Axis Communications Q6044-E - page 7
AXIS Q60 Series WARNING • Risk of explosion if the battery is incorrectly replaced. • Replace only with an identical battery or a battery which is recommended by Axis. • Dispose of used batteries according to local regulations or the battery manufacturer's instructions. Dome Cover NO NO NO TICE TICE TICE • Be careful not to scratch, da ...
-
Axis Communications Q6044-E - page 8
8 ...
-
Axis Communications Q6044-E - page 9
AXIS Q60 Series Installation Guide This Installation Guide provides instructions for installing AXIS Q6042-E/Q6044-E/Q6045-E PTZ Dome Network Camera on your network. For other aspects of using the product, see the User Manual available at www .axis.com Installation Steps 1. Make sure the package contents, tools and other materials necessary for the ...
-
Axis Communications Q6044-E - page 10
AXIS Q60 Series Optional Accessories • AXIS T91A Mounting Accessories • Smoked dome cover • RJ45 IP66-rated Cable with Premounted Connector (CAT6) 5 m • AXIS T83 10 Video Surveillance Control Board • AXIS T90A Illuminators • Installation Display • Midspan For information about available accessories, see www .axis.com Hardware Overview ...
-
Axis Communications Q6044-E - page 11
AXIS Q60 Series 5 P art number (P/N) & Serial number (S/N) 6 P ower button 7 Heater 8 Control button 9 Status LED indicator 1 0 SD card slot (SDHC) Dome Cover 1 2 3 4 5 6 1 Dome bracket screw PH2 (4x) 2 Dome bracket 3 Rubber gasket 4 Dome ring 5 Dome ring screw T30 (4x) 6 Dome cover 1 1 E N G L I SH ...
-
Axis Communications Q6044-E - page 12
AXIS Q60 Series Sunshield 2 1 1 Screw holes 2 Holes for unit holders LED Indicators LED Color Indication Unlit Connection and normal operation Amber Steady during startup. Flashes during rmware upgrade. Amber/red Flashes amber/red if network connection is unavailable or lost. Red Flashes red for rmware upgrade failure. Status Green Shows stea ...
-
Axis Communications Q6044-E - page 13
AXIS Q60 Series Green, ashing Fast ash when input voltage is out of range or other internal error . AC Green Steady when AC power input connected. Connectors and Buttons For specications and operating conditions, see page 13 . Specications Operating Conditions The Axis product is intended for outdoor use. Product Classication Tempera ...
-
Axis Communications Q6044-E - page 14
AXIS Q60 Series Install the Hardware NO NO NO TICE TICE TICE • The AXIS product shall be connected using a shielded network cable (STP). All cables connecting the product to the midspan shall be shielded (STP) and intended for their specic use. Make sure that the midspan is properly grounded. For information about regulatory requirements, see ...
-
Axis Communications Q6044-E - page 15
AXIS Q60 Series 3. Make sure the rubber gasket is tted correctly on the dome cover . 4. Align the bulge on the dome cover with one of the logotypes on the dome ring. 5. Attach the dome bracket and the dome cover to the dome ring and tighten the screws (torque 1.2 Nm). 6. To install an SD card (not included), see Install an SD Card on page 15 . 7 ...
-
Axis Communications Q6044-E - page 16
AXIS Q60 Series 3 4 2 1 5 1 Network connector – RJ45 Push-pull Connector (IP66) 2 Network connector and network connector shield 3 Ground screw T20 4 Washer 5 Cable shoe 5. Attach the grounding wire to the cable shoe using cable shoe pliers. 6. Put the cable shoe and washer back in their original positions and tighten the screw (torque 0.5 Nm). M ...
-
Axis Communications Q6044-E - page 17
AXIS Q60 Series 1 2 3 4 1 Screw T30 (3x) 2 Slot for unit holder (3x) 3 Safety wire 4 Wall bracket (mounting example) 1 1. Install the supplied midspan. See page 17 . Install the Midspan The supplied midspan enables Axis network video products with high power consumption to receive data and power over the same network cable. 1. Connect the midspan ( ...
-
Axis Communications Q6044-E - page 18
AXIS Q60 Series 1 2 3 4 1 Data and power out (connect to Axis product) 2 Data in (connect to network) 3 AC input LED indicator 4 P ort LED indicator 4. Make sure that the LEDs on the midspan indicate the correct conditions. See Midspan LED Indicators on page 12 . Access the Product Use the tools provided on the Installation and Management Software ...
-
Axis Communications Q6044-E - page 19
AXIS Q60 Series 4. The process is now complete. The product has been reset to the factory default settings. If no DHCP server is available on the network, the default IP address is 192.168.0.90 5. Using the installation and management software tools, assign an IP address, set the password and access the video stream. It is also possible to reset pa ...
-
Axis Communications Q6044-E - page 20
...
-
Axis Communications Q6044-E - page 21
Regulatory I nformation USA This equipment has been tested using an unshielded network cable (UTP) and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. This equipment has also been tested using a shielded network cable (STP) and found to comply with the limits for a Class A digital device, pursuant ...
-
Axis Communications Q6044-E - page 22
...
-
Axis Communications Q6044-E - page 23
...
-
Axis Communications Q6044-E - page 24
Installation Guide V er . M2.7 AXIS Q60 Series Date: July 20 14 © Axis Communications AB, 20 14 P art No. 58978 ...
¿Tienes una pregunta acerca de Axis Communications Q6044-E?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Axis Communications Q6044-E, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Axis Communications Q6044-E probablemente compartirá una forma de solucionarlo.