-
Infinity TSS-SUB4000 - page 1
TSS-SUB400 0 Owner’ s Guide (120V) T OT AL S PEAKER S OLUTIONS TSS-4000 ...
-
Infinity TSS-SUB4000 - page 2
ii TSS-SUB4000 1. Read these instructions . 2. Keep these instructions . 3. Heed all warnings . 4. F ollow all instr uctions . 5. Do not use this apparatus near water . 6. Clean only with a dry cloth. 7. Do not block any ventilation openings . Install in accordance with the manuf acturer’ s instructions . 8. Do not install near any heat sour ces ...
-
Infinity TSS-SUB4000 - page 3
iii TSS-SUB4000 T able of Contents ii Important Safety Pr ecautions 1 Unpacking the Subwoofer 1 Placement 2 Controls and Connections 3 Connections 4 Operation 5 Room Adaptive Bass Optimization System ™ (R.A.B.O .S . ™ ) 6 Contents of the R.A.B.O .S. T est CD 6 The R.A.B.O .S. Sound-Le vel Meter (RSLM) 7 Initial System-Lev el Setting 7 Setting t ...
-
Infinity TSS-SUB4000 - page 4
TSS-SUB4000 1 Infinity T o tal Solut ions ™ TSS-SUB4000 The Infinity T otal Solutions TSS-SUB4000 continues Infinity’ s long-standing commitment to accurate sound r eproduction. Our propr ietary Metal Matrix Diaphra gm ™ (MMD ® ) dr iv er , high-power ed amplif ier and pr oprietary Room Adaptive Bass Optimization System, ™ along with a rig ...
-
Infinity TSS-SUB4000 - page 5
2 TSS-SUB4000 Rear Panel C ONTROLS AND C ONNECTIONS ¡ Subwoofer Le vel (V olume) Contr ol ™ Line-Lev el Inputs £ Normal/LFE Low-Pass Selector ¢ Phase Switch ∞ Power Switch Room Adapt iv e Bass Optimizat ion Syst em Controls (see pa ge 5) § R.A.B.O .S. Selector ¶ R.A.B.O .S. Le v el Adjustment • R.A.B.O .S. Bandwidth Adjustment ª R.A.B.O ...
-
Infinity TSS-SUB4000 - page 6
3 TSS-SUB4000 C ONNECTIONS If you ha ve a Dolb y* Digit al or DTS ® receiv er/processor with a low-fr equency-e ffec ts (LFE) outpu t: • Set Low-P ass Switch t o Off . NO TE: In this case , you do not need to use a Y connector . Simply connect the LFE output on your recei ver/pr ocessor to either the left or right input on the subwoof er . If yo ...
-
Infinity TSS-SUB4000 - page 7
4 TSS-SUB4000 Pow er On Plug your su bw oo fe r’s AC cor d into a wall outlet. Do not use the outlets on the back of the recei ver . Initially set the Subwoofer Le vel (V olume) Contr ol ¡ to the “min” position. T urn on your sub by pressing the P ower Switch ∞ on the rear panel. Au to On/St andby With the P ower Switch ∞ in the ON posit ...
-
Infinity TSS-SUB4000 - page 8
5 TSS-SUB4000 Infinity’ s R.A.B.O.S . is a simple-to-use, yet sophisticated, low-fr equency calibr ation system. It is designed to work in conjunction with the TSS-SUB4000 self-amplified subwoof er . The TSS-SUB4000 subwoofer contains a parametric equaliz er that you will adjust as indicated by the R.A.B.O .S. test r esults. Following these instr ...
-
Infinity TSS-SUB4000 - page 9
6 TSS-SUB4000 P ower is switched on or off by pr essing the button dir ectly below the bar -graph window . When the unit is on, one or more LEDs will always be illuminated. The function of the LEDs is descr ibed in the following section. • Power -On/Low Signal: This is indicated by the illumination of any LED on the bar graph. If the sound lev el ...
-
Infinity TSS-SUB4000 - page 10
7 TSS-SUB4000 Init ial Syst em-Level Se tting The following steps will set the pla yback lev el of the system to the corr ect le vel f or all tests that follow . T urn the system volume to minimum. Cue the R.A.B.O .S. T est CD to T rack 2 and pr ess Pause II . T his track will pr oduce band-limited pink noise in both the left and right channels . P ...
-
Infinity TSS-SUB4000 - page 11
8 TSS-SUB4000 Each of the following tr acks produces a low-fr equency test tone. T he range of these tests is fr om 100Hz down to 20Hz. The frequency of each test is announced bef ore it begins . The fir st test is the highest frequency (100Hz); therefor e, you will be marking the template fr om right to left. Each frequency point is listed acr oss ...
-
Infinity TSS-SUB4000 - page 12
9 TSS-SUB4000 At this point, you may simply enter the data you just measured into the R.A.B.O .S. calculator , found on the Infinity Web site at www .infinitysystems.com. After entering the data, this R.A.B.O.S . wizard will retur n the corr ect settings f or all thr ee R.A.B.O .S. controls: ¶ , • and ª . Skip to page 14 and adjust these contr ...
-
Infinity TSS-SUB4000 - page 13
10 TSS-SUB4000 Using the Width Select or Read the following instr uctions carefully . The example presented ma y not look like the graph you just cr eated. Focus on the concepts and techniques pr esented. Specific cases will be discussed later . Y ou will use the Measurement T emplate just completed and the Width Selector to determine the cor rect ...
-
Infinity TSS-SUB4000 - page 14
11 TSS-SUB4000 The pointer on the slider will indicate the cor rect width setting. Enter this number in the Width field of the Measurement T emplate. In our example, the width is 12.5%. It is not realistic to expect a perf ect fit. Acoustic measur ements encompass the beha vior of not only the speaker s but of the room and its contents as well. Ref ...
-
Infinity TSS-SUB4000 - page 15
12 TSS-SUB4000 Example 2. T wo Response P eaks: Character ized by two r esponse peaks, approximately equal in amplitude and width. This r equires that you make a choice between the two peaks. In situations like this, the higher frequency peak will alwa ys be more audible and objectionable . Response peaks below 45Hz, unless e xtreme , can actually ...
-
Infinity TSS-SUB4000 - page 16
13 TSS-SUB4000 2. Reset the test level: Return to the section “Setting the Subwoof er T est Level” on page 7. Perform the pr ocedure as described. 3. Repeat the measurements: Now that you are familiar with the measur ement pr ocess, you can go much faster by using T racks 27–50. These tracks contain all the test tones necessary for measuremen ...
-
Infinity TSS-SUB4000 - page 17
14 TSS-SUB4000 2. Reset the test level: Return to the section “Setting the Subwoofer T est Level” on page 7. Perform the pr ocedure as described. 3. Repeat the measurements: Now that you are familiar with the measur ement pr ocess, you can go much faster by using T racks 27–50. These tracks contain all the test tones necessary for measurement ...
-
Infinity TSS-SUB4000 - page 18
15 TSS-SUB4000 If using more than one subwoof er , always adjust both subwoofer s together . Adjust the controls as indicated by the Measur ement T emplate. Each value shown in the table is r epresented by detents in the R.A.B.O .S. controls . Simply count the number of detents necessary , indicated by the results of your R.A.B.O .S. T est. TSS-SUB ...
-
Infinity TSS-SUB4000 - page 19
16 TSS-SUB4000 M AINTENANCE AND S ERVICE T he enclosur e and grille may be cleaned using a soft c loth to remo ve f ingerprints or to wipe off dust. All wiring connections should be inspected and c leaned or remade per iodically . The fr equency of maintenance depends on the metals in v olved in the connections , atmospheric conditions, and other f ...
-
Infinity TSS-SUB4000 - page 20
17 TSS-SUB4000 ...
-
Infinity TSS-SUB4000 - page 21
18 TSS-SUB4000 ...
-
Infinity TSS-SUB4000 - page 22
19 TSS-SUB4000 TSS-SUB4000 F requenc y Response 28Hz – 150Hz (–3dB) 24Hz – 180Hz (–6dB) Maximum Amplifier Output 400 watts RMS (20Hz – 150Hz with no more than 0.1% THD) Crossov er F requenc y 150Hz, 12dB/octav e Driver 12" (300mm) MMD ® Dimensions (H x W x D) 17-1/2" x 17-1/4" x 11-1/8" (445mm x 438mm x 283mm) Weight ...
-
Infinity TSS-SUB4000 - page 23
N O TES ...
-
Infinity TSS-SUB4000 - page 24
© 2004 Harman International Industries , Incorporated Infinity Systems, 250 Crosswa ys Park Dri ve , Woodbury , NY 11797 USA 516.674.4INF (4463) www .infinitysystems.com * T rademark of Dolby Laborator ies. DTS is a registered trademark of Digital Theater Systems, Inc. Inf inity and MMD ar e r egistered tr ademarks, and Metal Matrix Diaphragm, Roo ...
¿Tienes una pregunta acerca de Infinity TSS-SUB4000?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Infinity TSS-SUB4000, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Infinity TSS-SUB4000 probablemente compartirá una forma de solucionarlo.