English dropdown-ico

Manual Infinity TSS-SUB4000

24 pages 0.84 mb
Download

Go to site of 24

Summary
  • Infinity TSS-SUB4000 - page 1

    TSS-SUB400 0 Owner’ s Guide (120V) T OT AL S PEAKER S OLUTIONS TSS-4000 ...

  • Infinity TSS-SUB4000 - page 2

    ii TSS-SUB4000 1. Read these instructions . 2. Keep these instructions . 3. Heed all warnings . 4. F ollow all instr uctions . 5. Do not use this apparatus near water . 6. Clean only with a dry cloth. 7. Do not block any ventilation openings . Install in accordance with the manuf acturer’ s instructions . 8. Do not install near any heat sour ces ...

  • Infinity TSS-SUB4000 - page 3

    iii TSS-SUB4000 T able of Contents ii Important Safety Pr ecautions 1 Unpacking the Subwoofer 1 Placement 2 Controls and Connections 3 Connections 4 Operation 5 Room Adaptive Bass Optimization System ™ (R.A.B.O .S . ™ ) 6 Contents of the R.A.B.O .S. T est CD 6 The R.A.B.O .S. Sound-Le vel Meter (RSLM) 7 Initial System-Lev el Setting 7 Setting t ...

  • Infinity TSS-SUB4000 - page 4

    TSS-SUB4000 1 Infinity T o tal Solut ions ™ TSS-SUB4000 The Infinity T otal Solutions TSS-SUB4000 continues Infinity’ s long-standing commitment to accurate sound r eproduction. Our propr ietary Metal Matrix Diaphra gm ™ (MMD ® ) dr iv er , high-power ed amplif ier and pr oprietary Room Adaptive Bass Optimization System, ™ along with a rig ...

  • Infinity TSS-SUB4000 - page 5

    2 TSS-SUB4000 Rear Panel C ONTROLS AND C ONNECTIONS ¡ Subwoofer Le vel (V olume) Contr ol ™ Line-Lev el Inputs £ Normal/LFE Low-Pass Selector ¢ Phase Switch ∞ Power Switch Room Adapt iv e Bass Optimizat ion Syst em Controls (see pa ge 5) § R.A.B.O .S. Selector ¶ R.A.B.O .S. Le v el Adjustment • R.A.B.O .S. Bandwidth Adjustment ª R.A.B.O ...

  • Infinity TSS-SUB4000 - page 6

    3 TSS-SUB4000 C ONNECTIONS If you ha ve a Dolb y* Digit al or DTS ® receiv er/processor with a low-fr equency-e ffec ts (LFE) outpu t: • Set Low-P ass Switch t o Off . NO TE: In this case , you do not need to use a Y connector . Simply connect the LFE output on your recei ver/pr ocessor to either the left or right input on the subwoof er . If yo ...

  • Infinity TSS-SUB4000 - page 7

    4 TSS-SUB4000 Pow er On Plug your su bw oo fe r’s AC cor d into a wall outlet. Do not use the outlets on the back of the recei ver . Initially set the Subwoofer Le vel (V olume) Contr ol ¡ to the “min” position. T urn on your sub by pressing the P ower Switch ∞ on the rear panel. Au to On/St andby With the P ower Switch ∞ in the ON posit ...

  • Infinity TSS-SUB4000 - page 8

    5 TSS-SUB4000 Infinity’ s R.A.B.O.S . is a simple-to-use, yet sophisticated, low-fr equency calibr ation system. It is designed to work in conjunction with the TSS-SUB4000 self-amplified subwoof er . The TSS-SUB4000 subwoofer contains a parametric equaliz er that you will adjust as indicated by the R.A.B.O .S. test r esults. Following these instr ...

  • Infinity TSS-SUB4000 - page 9

    6 TSS-SUB4000 P ower is switched on or off by pr essing the button dir ectly below the bar -graph window . When the unit is on, one or more LEDs will always be illuminated. The function of the LEDs is descr ibed in the following section. • Power -On/Low Signal: This is indicated by the illumination of any LED on the bar graph. If the sound lev el ...

  • Infinity TSS-SUB4000 - page 10

    7 TSS-SUB4000 Init ial Syst em-Level Se tting The following steps will set the pla yback lev el of the system to the corr ect le vel f or all tests that follow . T urn the system volume to minimum. Cue the R.A.B.O .S. T est CD to T rack 2 and pr ess Pause II . T his track will pr oduce band-limited pink noise in both the left and right channels . P ...

  • Infinity TSS-SUB4000 - page 11

    8 TSS-SUB4000 Each of the following tr acks produces a low-fr equency test tone. T he range of these tests is fr om 100Hz down to 20Hz. The frequency of each test is announced bef ore it begins . The fir st test is the highest frequency (100Hz); therefor e, you will be marking the template fr om right to left. Each frequency point is listed acr oss ...

  • Infinity TSS-SUB4000 - page 12

    9 TSS-SUB4000 At this point, you may simply enter the data you just measured into the R.A.B.O .S. calculator , found on the Infinity Web site at www .infinitysystems.com. After entering the data, this R.A.B.O.S . wizard will retur n the corr ect settings f or all thr ee R.A.B.O .S. controls: ¶ , • and ª . Skip to page 14 and adjust these contr ...

  • Infinity TSS-SUB4000 - page 13

    10 TSS-SUB4000 Using the Width Select or Read the following instr uctions carefully . The example presented ma y not look like the graph you just cr eated. Focus on the concepts and techniques pr esented. Specific cases will be discussed later . Y ou will use the Measurement T emplate just completed and the Width Selector to determine the cor rect ...

  • Infinity TSS-SUB4000 - page 14

    11 TSS-SUB4000 The pointer on the slider will indicate the cor rect width setting. Enter this number in the Width field of the Measurement T emplate. In our example, the width is 12.5%. It is not realistic to expect a perf ect fit. Acoustic measur ements encompass the beha vior of not only the speaker s but of the room and its contents as well. Ref ...

  • Infinity TSS-SUB4000 - page 15

    12 TSS-SUB4000 Example 2. T wo Response P eaks: Character ized by two r esponse peaks, approximately equal in amplitude and width. This r equires that you make a choice between the two peaks. In situations like this, the higher frequency peak will alwa ys be more audible and objectionable . Response peaks below 45Hz, unless e xtreme , can actually ...

  • Infinity TSS-SUB4000 - page 16

    13 TSS-SUB4000 2. Reset the test level: Return to the section “Setting the Subwoof er T est Level” on page 7. Perform the pr ocedure as described. 3. Repeat the measurements: Now that you are familiar with the measur ement pr ocess, you can go much faster by using T racks 27–50. These tracks contain all the test tones necessary for measuremen ...

  • Infinity TSS-SUB4000 - page 17

    14 TSS-SUB4000 2. Reset the test level: Return to the section “Setting the Subwoofer T est Level” on page 7. Perform the pr ocedure as described. 3. Repeat the measurements: Now that you are familiar with the measur ement pr ocess, you can go much faster by using T racks 27–50. These tracks contain all the test tones necessary for measurement ...

  • Infinity TSS-SUB4000 - page 18

    15 TSS-SUB4000 If using more than one subwoof er , always adjust both subwoofer s together . Adjust the controls as indicated by the Measur ement T emplate. Each value shown in the table is r epresented by detents in the R.A.B.O .S. controls . Simply count the number of detents necessary , indicated by the results of your R.A.B.O .S. T est. TSS-SUB ...

  • Infinity TSS-SUB4000 - page 19

    16 TSS-SUB4000 M AINTENANCE AND S ERVICE T he enclosur e and grille may be cleaned using a soft c loth to remo ve f ingerprints or to wipe off dust. All wiring connections should be inspected and c leaned or remade per iodically . The fr equency of maintenance depends on the metals in v olved in the connections , atmospheric conditions, and other f ...

  • Infinity TSS-SUB4000 - page 20

    17 TSS-SUB4000 ...

  • Infinity TSS-SUB4000 - page 21

    18 TSS-SUB4000 ...

  • Infinity TSS-SUB4000 - page 22

    19 TSS-SUB4000 TSS-SUB4000 F requenc y Response 28Hz – 150Hz (–3dB) 24Hz – 180Hz (–6dB) Maximum Amplifier Output 400 watts RMS (20Hz – 150Hz with no more than 0.1% THD) Crossov er F requenc y 150Hz, 12dB/octav e Driver 12" (300mm) MMD ® Dimensions (H x W x D) 17-1/2" x 17-1/4" x 11-1/8" (445mm x 438mm x 283mm) Weight ...

  • Infinity TSS-SUB4000 - page 23

    N O TES ...

  • Infinity TSS-SUB4000 - page 24

    © 2004 Harman International Industries , Incorporated Infinity Systems, 250 Crosswa ys Park Dri ve , Woodbury , NY 11797 USA 516.674.4INF (4463) www .infinitysystems.com * T rademark of Dolby Laborator ies. DTS is a registered trademark of Digital Theater Systems, Inc. Inf inity and MMD ar e r egistered tr ademarks, and Metal Matrix Diaphragm, Roo ...

Manufacturer Infinity Category Speaker

Documents that we receive from a manufacturer of a Infinity TSS-SUB4000 can be divided into several groups. They are, among others:
- Infinity technical drawings
- TSS-SUB4000 manuals
- Infinity product data sheets
- information booklets
- or energy labels Infinity TSS-SUB4000
All of them are important, but the most important information from the point of view of use of the device are in the user manual Infinity TSS-SUB4000.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Infinity TSS-SUB4000, service manual, brief instructions and user manuals Infinity TSS-SUB4000. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Infinity TSS-SUB4000.

Similar manuals

A complete manual for the device Infinity TSS-SUB4000, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Infinity TSS-SUB4000 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Infinity TSS-SUB4000.

A complete Infinity manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Infinity TSS-SUB4000 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Infinity TSS-SUB4000, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Infinity TSS-SUB4000, that we can find in the current document
3. Tips how to use the basic functions of the device Infinity TSS-SUB4000 - which should help us in our first steps of using Infinity TSS-SUB4000
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Infinity TSS-SUB4000
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Infinity TSS-SUB4000 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Infinity TSS-SUB4000?

Use the form below

If you did not solve your problem by using a manual Infinity TSS-SUB4000, ask a question using the form below. If a user had a similar problem with Infinity TSS-SUB4000 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)