Español dropdown-ico

Manual de instrucciones Garland H280

23 de páginas 1.29 mb
Descargar

Pasar a la página of 23

Summary
  • Garland H280 - page 1

    03/09/09 P/N 4523367 Page 1 H280-series Valve Ov erheat / Relocation Kit Inst ructions: RC O vens Instructions for A pplying Kit #4523368 This kit is for a convectio n RC, 36” ov en only . For a Standard 36” oven, use Kit #4522559 Installation Prerequi sites:  RC Oven, Piezoelectr ic Ignition  U-Burner with no wel ded brack et Tools Neede ...

  • Garland H280 - page 2

    03/09/09 P/N 4523367 Page 2 Instructions: 1) Remove Kick Plate  Unscrew and set aside  This kick plate will n ot be reinstalled. A replacem ent is provided in th e k it. 2) Remove Safety V alve  The following steps will apply for a Baso Valve: 1) Unscrew 11/16” com pression nut on o ven orifice fitting. 2) Unscrew 11/16” com pression n ...

  • Garland H280 - page 3

    03/09/09 P/N 4523367 Page 3 3) Unscrew Igniter Bracket  Unscrew the two scre ws holding down the igniter brac ket to the orifice brac ket. Left: Before rem oval, location of screws shown b y arrows Right: After rem oval 4) Remove Door Springs  Once the springs are removed, the ov en door will be free to fall. Use a stron g tape to keep the ov ...

  • Garland H280 - page 4

    03/09/09 P/N 4523367 Page 4  Pry upward with the sc rewdriver. W hile holding this position, unhook the oven do or hinge link. Unhooked oven door h inge link  Use flat head scre wdriver to pry spring f rom bell crank assem bly. Remove spring. Prying spring fr om bell crank assem bly ...

  • Garland H280 - page 5

    03/09/09 P/N 4523367 Page 5  For the door hinge w ith a microswitch:  Unscrew the m icroswitch brack et from the oven fram e. It is important that the microswitch be remov ed prior to removing the spring to prevent damage t o the microswitch when the s prings are reinstalled later. Microswitch brack et held to oven fram e by two screws indica ...

  • Garland H280 - page 6

    03/09/09 P/N 4523367 Page 6 5) Remove Orifice Br acket  After rem oving the igniter bracket, the orifice brack et will be held in place b y a single screw directl y above the ori fice. Note that with the rem oval of the igniter brack et, the orifice brack et is held down by a s ingle screw as shown by the arro w ...

  • Garland H280 - page 7

    03/09/09 P/N 4523367 Page 7 6) Install Extension Fitting (if applicable)  If pilot gas tube going int o the valve alread y has an extension pi ece (short piece of tubing plus 3/16” b rass fitting), unscrew th e shorter piece of tubing and p roceed to Step 13. Otherwise, fo llow these steps to inst all the proper fitting.  This step must be ...

  • Garland H280 - page 8

    03/09/09 P/N 4523367 Page 8 7) Remove Left and Righ t Front Shields  Both shields are attac hed to the up per support bar using 3 scr ews. Left: Left side fr ont shield, location of screws sho wn by arrows Right: Right side f ront shield, location of scr ews shown by arrows 8) Remove Burner  Burner is not scr ewed down to oven floor and can b ...

  • Garland H280 - page 9

    03/09/09 P/N 4523367 Page 9 9) Unscrew Pilot Bra cket from Oven Flo or  The brack et is held down to the oven floor us ing two screws. This brack et will not be reinstalled. Left: Pilot assem bly with bracket m ounted to oven floor Right: Pilot assem bly with bracket rem oved 10) Detach Igniter and B racket from Pilot Ass embly  Us e a pair o ...

  • Garland H280 - page 10

    03/09/09 P/N 4523367 Page 10 11) Assemble New Pilot A ssembly  A colored line on the to p of the pilot indicates t he type of f uel used. A BL ACK line is used on a natural g as pilot, whereas a RED line is used o n a propane pi lot. Ensure the proper pilot is used.  Insert sheath onto new pilot assem bly ignition wire  Push sheath onto wi ...

  • Garland H280 - page 11

    03/09/09 P/N 4523367 Page 11  Reattach original ignit er Connection of taped ignition wire end to orig inal igniter  Attach flex tube to pi lot assembl y  Unscrew the nut on the end of the selected pilot to re lease the nut, the f errule and the orifice. Install the nut and the ferrule on on e end of the flex tube.  Place the orifice ba ...

  • Garland H280 - page 12

    03/09/09 P/N 4523367 Page 12  Attach new Roberts haw therm ocouple to pilot assem bly  Push the therm ocouple all the w ay into its slot on the pilot. Left: Wrong installation. Therm ocouple not pushed all the wa y through socket. Right: Correct installati on. Thermocouple pushed all the way through sock et. 12) Attach New Pilot As sembly to ...

  • Garland H280 - page 13

    03/09/09 P/N 4523367 Page 13 13) Install New Burner  Ensure that the brac ket at the tip of the burn er locks onto the bracket attached to the oven floor. No sc rews are necessary fo r this procedure .  The burner m ay not st and up perfectly b y itself. The ins tallation of the oven orifice later will correct this prob lem. New burner and pi ...

  • Garland H280 - page 14

    03/09/09 P/N 4523367 Page 14 15) Reinstall Orifice Br acket  Refer to Step 5 f or orifice bracket connect ions  Make sure that the orifice is inserted straight into the burner and n ot at an angle Orifice inserted straight into burner opening ...

  • Garland H280 - page 15

    03/09/09 P/N 4523367 Page 15 16) Reinstall Door Springs  Refer to Step 4 f or door spring connections  For the door hinge with no microswitch:  Hook on one end of the spring to the hook s from the or ifice bracket  Place a screwdriver underneath the opposite end of the spring an d pry upward to hook that end onto the bell crank ass embl ...

  • Garland H280 - page 16

    03/09/09 P/N 4523367 Page 16 17) Reinstall Igniter Bra cket Refer to Step 3 f or igniter bracket connect ions 18) Attach Main Burner Gas L ine Flex Tubes onto V alve  Two brass fittings (Part 7, Assem bly Drawing) should alrea dy be installed on the Mai n Burner gas inlet and o utlet on the Baso valve. Oth erwise, they are inc luded in the kit s ...

  • Garland H280 - page 17

    03/09/09 P/N 4523367 Page 17 19) Screw on Pilot Gas Fle x Tube, Adjust Main Burn er Gas Fitting  Remove the brass nut and ferr ule originally on the pilot gas outlet on the Baso valve (Part 5 and Part 6, Assembly Drawing). Install them onto the free end of the flex t ube.  Screw the pilot gas flex t ube onto the Baso valve pilot gas outlet. T ...

  • Garland H280 - page 18

    03/09/09 P/N 4523367 Page 18 20) Install New Pilot Gas Tu be  If a new 3/16” fitting (Part 4, Assem bly Drawing) was installed on the pilot gas tube (Part 3, Assembl y Drawing), uns crew the nut on the free en d of the fitting to release th e nut and the ferrule. If a f itting was alread y installed on the pilot gas tube, u nscrew one end of t ...

  • Garland H280 - page 19

    03/09/09 P/N 4523367 Page 19 21) Connect Remaining Tubes and Thermo couple  The free end of each 7/16” flex tube from the valve should be fitted with a 7/ 16” nut (Part 10, Assem bly Drawing) and 7/16” ferrule (Part 11, Ass embly Drawing).  Connect the 7/16” f lex tube and the therm ocouple. Tighten all connecti o ns.  The final tu ...

  • Garland H280 - page 20

    03/09/09 P/N 4523367 Page 20 23) Attach Bracket to Ov en For Standard Ovens:  Unscrew the two scre ws holding the orifice brack et to the lower oven fr ame.  Slip the brack et (Part 8, Assembly Drawing) un derneath the valve ass emb ly such that the taller face is flush up a gainst the lower ov en frame.  Position the screw ho les on the b ...

  • Garland H280 - page 21

    03/09/09 P/N 4523367 Page 21 24) Attach Valve Onto B racket  The valve is attache d to the bracket using the b olt and nut provided (P art 13 and Part 12, Assem bly Drawing). Insert t he bolt into the hole thro ugh the valve and align it wit h the small hole on the back of the brack et. The large hole on the fr ont may be used to insert the bolt ...

  • Garland H280 - page 22

    03/09/09 P/N 4523367 Page 22 25) Install New Kick Plate  The new kick plate (Part 14, Assem bly Drawing) slants outwards to accom modate the valve. Ensure that the corr ect kick panel is installed. Left: Old kick plate with flat profile. Do not install this kick pl ate. Right: New k ick plate with slanted profile.  The new kick plate is desig ...

  • Garland H280 - page 23

    03/09/09 P/N 4523367 Page 23 Installation Complete Installation Com plete – Kick Plate Off Installation Com plete – Kick Plate On ...

Fabricante Garland Categoría Oven

Los documentos del dispositivo Garland H280 que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Garland
- manuales de instrucciones H280
- hojas de producto Garland
- folletos informativos
- o etiquetas energéticas Garland H280
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Garland H280.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Garland H280, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Garland H280. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Garland H280.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Garland H280, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Garland H280. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Garland H280.

El manual de instrucciones completo de Garland debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Garland H280 - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Garland H280, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Garland H280 que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Garland H280 - que deben facilitarnos los primeros pasos durante el uso de Garland H280
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Garland H280
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Garland H280 en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Garland H280?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Garland H280, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Garland H280 probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Captcha
Nueva imagen

Comentarios (0)