Garland H280の取扱説明書

23ページ 1.29 mb
ダウンロード

ページに移動 of 23

Summary
  • Garland H280 - page 1

    03/09/09 P/N 4523367 Page 1 H280-series Valve Ov erheat / Relocation Kit Inst ructions: RC O vens Instructions for A pplying Kit #4523368 This kit is for a convectio n RC, 36” ov en only . For a Standard 36” oven, use Kit #4522559 Installation Prerequi sites:  RC Oven, Piezoelectr ic Ignition  U-Burner with no wel ded brack et Tools Neede ...

  • Garland H280 - page 2

    03/09/09 P/N 4523367 Page 2 Instructions: 1) Remove Kick Plate  Unscrew and set aside  This kick plate will n ot be reinstalled. A replacem ent is provided in th e k it. 2) Remove Safety V alve  The following steps will apply for a Baso Valve: 1) Unscrew 11/16” com pression nut on o ven orifice fitting. 2) Unscrew 11/16” com pression n ...

  • Garland H280 - page 3

    03/09/09 P/N 4523367 Page 3 3) Unscrew Igniter Bracket  Unscrew the two scre ws holding down the igniter brac ket to the orifice brac ket. Left: Before rem oval, location of screws shown b y arrows Right: After rem oval 4) Remove Door Springs  Once the springs are removed, the ov en door will be free to fall. Use a stron g tape to keep the ov ...

  • Garland H280 - page 4

    03/09/09 P/N 4523367 Page 4  Pry upward with the sc rewdriver. W hile holding this position, unhook the oven do or hinge link. Unhooked oven door h inge link  Use flat head scre wdriver to pry spring f rom bell crank assem bly. Remove spring. Prying spring fr om bell crank assem bly ...

  • Garland H280 - page 5

    03/09/09 P/N 4523367 Page 5  For the door hinge w ith a microswitch:  Unscrew the m icroswitch brack et from the oven fram e. It is important that the microswitch be remov ed prior to removing the spring to prevent damage t o the microswitch when the s prings are reinstalled later. Microswitch brack et held to oven fram e by two screws indica ...

  • Garland H280 - page 6

    03/09/09 P/N 4523367 Page 6 5) Remove Orifice Br acket  After rem oving the igniter bracket, the orifice brack et will be held in place b y a single screw directl y above the ori fice. Note that with the rem oval of the igniter brack et, the orifice brack et is held down by a s ingle screw as shown by the arro w ...

  • Garland H280 - page 7

    03/09/09 P/N 4523367 Page 7 6) Install Extension Fitting (if applicable)  If pilot gas tube going int o the valve alread y has an extension pi ece (short piece of tubing plus 3/16” b rass fitting), unscrew th e shorter piece of tubing and p roceed to Step 13. Otherwise, fo llow these steps to inst all the proper fitting.  This step must be ...

  • Garland H280 - page 8

    03/09/09 P/N 4523367 Page 8 7) Remove Left and Righ t Front Shields  Both shields are attac hed to the up per support bar using 3 scr ews. Left: Left side fr ont shield, location of screws sho wn by arrows Right: Right side f ront shield, location of scr ews shown by arrows 8) Remove Burner  Burner is not scr ewed down to oven floor and can b ...

  • Garland H280 - page 9

    03/09/09 P/N 4523367 Page 9 9) Unscrew Pilot Bra cket from Oven Flo or  The brack et is held down to the oven floor us ing two screws. This brack et will not be reinstalled. Left: Pilot assem bly with bracket m ounted to oven floor Right: Pilot assem bly with bracket rem oved 10) Detach Igniter and B racket from Pilot Ass embly  Us e a pair o ...

  • Garland H280 - page 10

    03/09/09 P/N 4523367 Page 10 11) Assemble New Pilot A ssembly  A colored line on the to p of the pilot indicates t he type of f uel used. A BL ACK line is used on a natural g as pilot, whereas a RED line is used o n a propane pi lot. Ensure the proper pilot is used.  Insert sheath onto new pilot assem bly ignition wire  Push sheath onto wi ...

  • Garland H280 - page 11

    03/09/09 P/N 4523367 Page 11  Reattach original ignit er Connection of taped ignition wire end to orig inal igniter  Attach flex tube to pi lot assembl y  Unscrew the nut on the end of the selected pilot to re lease the nut, the f errule and the orifice. Install the nut and the ferrule on on e end of the flex tube.  Place the orifice ba ...

  • Garland H280 - page 12

    03/09/09 P/N 4523367 Page 12  Attach new Roberts haw therm ocouple to pilot assem bly  Push the therm ocouple all the w ay into its slot on the pilot. Left: Wrong installation. Therm ocouple not pushed all the wa y through socket. Right: Correct installati on. Thermocouple pushed all the way through sock et. 12) Attach New Pilot As sembly to ...

  • Garland H280 - page 13

    03/09/09 P/N 4523367 Page 13 13) Install New Burner  Ensure that the brac ket at the tip of the burn er locks onto the bracket attached to the oven floor. No sc rews are necessary fo r this procedure .  The burner m ay not st and up perfectly b y itself. The ins tallation of the oven orifice later will correct this prob lem. New burner and pi ...

  • Garland H280 - page 14

    03/09/09 P/N 4523367 Page 14 15) Reinstall Orifice Br acket  Refer to Step 5 f or orifice bracket connect ions  Make sure that the orifice is inserted straight into the burner and n ot at an angle Orifice inserted straight into burner opening ...

  • Garland H280 - page 15

    03/09/09 P/N 4523367 Page 15 16) Reinstall Door Springs  Refer to Step 4 f or door spring connections  For the door hinge with no microswitch:  Hook on one end of the spring to the hook s from the or ifice bracket  Place a screwdriver underneath the opposite end of the spring an d pry upward to hook that end onto the bell crank ass embl ...

  • Garland H280 - page 16

    03/09/09 P/N 4523367 Page 16 17) Reinstall Igniter Bra cket Refer to Step 3 f or igniter bracket connect ions 18) Attach Main Burner Gas L ine Flex Tubes onto V alve  Two brass fittings (Part 7, Assem bly Drawing) should alrea dy be installed on the Mai n Burner gas inlet and o utlet on the Baso valve. Oth erwise, they are inc luded in the kit s ...

  • Garland H280 - page 17

    03/09/09 P/N 4523367 Page 17 19) Screw on Pilot Gas Fle x Tube, Adjust Main Burn er Gas Fitting  Remove the brass nut and ferr ule originally on the pilot gas outlet on the Baso valve (Part 5 and Part 6, Assembly Drawing). Install them onto the free end of the flex t ube.  Screw the pilot gas flex t ube onto the Baso valve pilot gas outlet. T ...

  • Garland H280 - page 18

    03/09/09 P/N 4523367 Page 18 20) Install New Pilot Gas Tu be  If a new 3/16” fitting (Part 4, Assem bly Drawing) was installed on the pilot gas tube (Part 3, Assembl y Drawing), uns crew the nut on the free en d of the fitting to release th e nut and the ferrule. If a f itting was alread y installed on the pilot gas tube, u nscrew one end of t ...

  • Garland H280 - page 19

    03/09/09 P/N 4523367 Page 19 21) Connect Remaining Tubes and Thermo couple  The free end of each 7/16” flex tube from the valve should be fitted with a 7/ 16” nut (Part 10, Assem bly Drawing) and 7/16” ferrule (Part 11, Ass embly Drawing).  Connect the 7/16” f lex tube and the therm ocouple. Tighten all connecti o ns.  The final tu ...

  • Garland H280 - page 20

    03/09/09 P/N 4523367 Page 20 23) Attach Bracket to Ov en For Standard Ovens:  Unscrew the two scre ws holding the orifice brack et to the lower oven fr ame.  Slip the brack et (Part 8, Assembly Drawing) un derneath the valve ass emb ly such that the taller face is flush up a gainst the lower ov en frame.  Position the screw ho les on the b ...

  • Garland H280 - page 21

    03/09/09 P/N 4523367 Page 21 24) Attach Valve Onto B racket  The valve is attache d to the bracket using the b olt and nut provided (P art 13 and Part 12, Assem bly Drawing). Insert t he bolt into the hole thro ugh the valve and align it wit h the small hole on the back of the brack et. The large hole on the fr ont may be used to insert the bolt ...

  • Garland H280 - page 22

    03/09/09 P/N 4523367 Page 22 25) Install New Kick Plate  The new kick plate (Part 14, Assem bly Drawing) slants outwards to accom modate the valve. Ensure that the corr ect kick panel is installed. Left: Old kick plate with flat profile. Do not install this kick pl ate. Right: New k ick plate with slanted profile.  The new kick plate is desig ...

  • Garland H280 - page 23

    03/09/09 P/N 4523367 Page 23 Installation Complete Installation Com plete – Kick Plate Off Installation Com plete – Kick Plate On ...

メーカー Garland カテゴリー Oven

Garland H280のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- H280の取扱説明書
- Garlandの製品カード
- パンフレット
- またはGarland H280の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Garland H280の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Garland H280の取り付け説明書、サービスマニュアル、簡易説明書、またはGarland H280のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Garland H280の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Garland H280デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがGarland H280を使用するのを助ける技術的文書のことです。説明書は通常、全てのGarland H280ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Garlandの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Garland H280の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははGarland H280の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Garland H280に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Garland H280デバイスの基本機能を使うにあたってのヒント。 Garland H280のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Garland H280に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるGarland H280のメーカー/サービスへの連絡先に関する情報。

Garland H280についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもGarland H280の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがGarland H280で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)