-
Pelco C3422M-B - page 1
INST ALLATION C3422M-B (3/08) Pressurized Spectra ® IV Series Pendant Back Box with Fiber Optic Option ...
-
Pelco C3422M-B - page 2
2 C3422M-B (3/08) Preinstallation NOTE: This manual is designed to be a reference tool for th e installatio n of your s ystem. For best results and ease of installation, the dome system should be asse mbled, pressurized, and tested before installati on. A Pressurized Spectra ® IV cable harness (supplied wit h the back box) is required to test and ...
-
Pelco C3422M-B - page 3
C3422M-B (3/08) 3 3. Loosen the V -band attached to the back box and let it hang to the side. Figure 3. Loosening the V-band 4. Prepar e the lowe r dome for installation : a. Remove the O-ring fro m the lower dome. b. Lightly appl y O-ring lubr icant (supp lied) to the O- ring. c. Reinstall the O-ring in th e groove on the trim ring . NOTES: • Re ...
-
Pelco C3422M-B - page 4
4 C3422M-B (3/08) Figure 5. Attaching the Back Box Leash 6. Install the dome drive. Refer to T able A for a list of compatible do me drives and back boxes. a. Set the DIP switch es located on the base of the dome dr ive. Refer to t he labels locat ed on the base of the dome drive or to Switch Settings on page 12 . b. Line up the blue and re d tabs ...
-
Pelco C3422M-B - page 5
C3422M-B (3/08) 5 7. Install the lower dome: a. Position the lo wer dome so tha t the blower duct inside the back box is between the studs att a ched to the insid e of the lower dome. b. Install the V-band a round the lower do me and then tighten th e fastener of the V -band. c. T est the operation of the unit b efore pressur izing the do me. Figur ...
-
Pelco C3422M-B - page 6
6 C3422M-B (3/08) d. Refer to the Operation/Prog ramming manu al (C 341 2M) for ins tru ctio ns on how to view the current readings for temperature and pressure. Reco rd t he ini tial te mpe rat ure and p re ssu re r ead ing s of the dom e in the spa ce provided be low: Initial T emp erature _______________ Initial Pressure _________________ NOTES: ...
-
Pelco C3422M-B - page 7
C3422M-B (3/08) 7 Site Installation 1. Feed a fiber optic cable (not supplied) an d the supplied wiri n g harness into the front of the mount and out the back of the mount. Connect the wire s as required. Refe r to T able B, T able C, and T able D on page 10, and T able E on page 11 for cable a nd wiring infor mation. Faste n the mount t o the moun ...
-
Pelco C3422M-B - page 8
8 C3422M-B (3/08) Figure 10. Removing the Back Box Mounting Plate 3. Thread the wiring fro m the mount throug h the mounting plat e, and then attach the mounting plate to the mount. If outdoors, apply threa d compound (sup plied) to the t hreads on the mounting p late. Figure 11. Attaching the Mounting Plate 4. Attach the wire har ness connec tor t ...
-
Pelco C3422M-B - page 9
C3422M-B (3/08) 9 Figure 12. Attaching the Wire Harness Connector ...
-
Pelco C3422M-B - page 10
10 C3422M-B (3/08) . NOTES: • Input power f or the dome is 24 V AC only . Power consumpt ion is 73 V A per dome. • Use a 24 V AC transformer with a minimum of 100 V A. . NOTE: As a minimum, UTP requires Cat5, 100-ohm twisted pair cable. T able B. Fiber Optic Cable T ypes Spectra Model Cable T ype Connector Single mode ( PRS models) 9/125 μm ca ...
-
Pelco C3422M-B - page 11
C3422M-B (3/08) 11 T able E. Configuration of Wire Harness Pin Wire Color Function 9-Conductor Cable AB l a c k A l a r m 1 BR e d A l a r m 2 C White Alarm 3 DG r e e n A l a r m 4 EB r o w n A l a r m 5 F Orange Alarm 6 G Y ellow Alarm 7 H Violet Ground – Blue N ot Used 5-Conductor Cable J Black Relay N.O. (Aux. 1) K Red Relay N.C. (Aux. 1) L G ...
-
Pelco C3422M-B - page 12
12 C3422M-B (3/08) Switch Settings WAR N IN G : If you are using Pelco D or Pelco P pr otocol control, your system may not oper ate if the baud rate and address swi tches are not set correc tly . The switches are set at the facto ry at the def aults for Pelco D protoc ol control (2400 bau d and address 1). T able F . Switch Settings for SW2 Special ...
-
Pelco C3422M-B - page 13
C3422M-B (3/08) 13 T able G. Switch Settings for SW1, Pelco P Protocol Control NOTE: For Coaxitron con trols, SW1 is no t used; set all switches t o the OFF pos ition. For Pelco D protocol control syst ems, refer to T able H on page 13. T able H. Switch Settings for SW1, Pelco D Protocol Control NOTE: For Coaxitron con trols, SW1 is no t used; set ...
-
Pelco C3422M-B - page 14
14 C3422M-B (3/08) SPECTRA ADDRESS SWITCH SETTI NG SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 71 ON ON ON OFF OFF OFF ON OFF 72 OFF OFF OFF ON OFF OFF ON OFF 73 ON OFF OFF ON OFF OFF ON OFF 74 OFF ON OFF ON OFF OFF ON OFF 75 ON ON OFF ON OFF OFF ON OFF 76 OFF OFF ON ON OFF OFF ON OFF 77 ON OFF ON ON OFF OFF ON OFF 78 OFF ON ON ON OFF OFF ON OF ...
-
Pelco C3422M-B - page 15
C3422M-B (3/08) 15 SPECTRA ADDRESS SWITCH SETTI NG SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 151 ON ON ON OFF ON OFF OFF ON 152 OFF OFF OFF ON ON OFF OFF ON 153 ON OFF OFF ON ON OFF OFF ON 154 OFF ON OFF ON ON OFF OFF ON 155 ON ON OFF ON ON OFF OFF ON 156 OFF OFF ON ON ON OFF OFF ON 157 ON OFF ON ON ON OFF OFF ON 158 OFF ON ON ON ON OFF OFF O ...
-
Pelco C3422M-B - page 16
16 C3422M-B (3/08) SPECTRA ADDRESS SWITCH SETTI NG SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 223 ON ON ON ON ON OFF ON ON 224 OFF OFF OFF OFF OFF ON ON ON 225 ON OFF OFF OFF OFF ON ON ON 226 OFF ON OFF OFF OFF ON ON ON 227 ON ON OFF O FF OFF ON ON ON 228 OFF OFF ON OFF OFF ON ON ON 229 ON OFF ON OFF OFF ON ON ON 230 OFF ON ON OFF OFF ON ON ON ...
-
Pelco C3422M-B - page 17
C3422M-B (3/08) 17 Specifications GENERAL Construction Back Box 316L stainless steel Dome Drive Aluminum, thermoplastic Lower Dome T rim Rin g 316L stainle ss steel Bubble Polycarbonate, 0 .09-inch thick V-Band 316L stainle ss steel Pressure Rel ief Brass Schrader V alve Brass Connector Nickel-plated steel Light Attenuat ion Smoked f/1.0 light loss ...
-
Pelco C3422M-B - page 18
18 C3422M-B (3/08) Input Power 24 V A C 73 VA nominal (with heater) 24 VDC 3 A nominal (with heater) Fuse 1.25 A Auxiliary Outputs 2 Alarm Inputs 7 5.9 (15.1) 11.6 (29.5) 10.6 (26.7) NOTE: VALUES IN PARENT HESES ARE CENTIMETERS; ALL OTHERS ARE INCHES. ...
-
Pelco C3422M-B - page 19
PRODUCT W ARRANTY AND RETURN INFORMA TION WARRANTY Pelco will r epair or repla c e, without charge, any merchandise p roved defectiv e in material or wor kmanship for a period of one year after the date o f shipment. Exceptions to this warranty are a s noted below: • Five years on fiber opt ic products and TW30 00 Series unshielded twis ted pair ...
-
Pelco C3422M-B - page 20
W orldwid e Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.c om ISO 9001 Australia | Finland | France | Germany | Italy | Macau | The Netherlands | Russia | Singapore South Africa | Spain | Sweden | United Arab Emirates ...
¿Tienes una pregunta acerca de Pelco C3422M-B?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Pelco C3422M-B, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Pelco C3422M-B probablemente compartirá una forma de solucionarlo.