-
JAI CV-M77 - page 1
CV-M77 Progressive Scan Camera CV-M77 Operation Manual Camera: Revision A Manual: Version 1.0 - 1 - ...
-
JAI CV-M77 - page 2
CV-M77 - 2 - ...
-
JAI CV-M77 - page 3
CV-M77 1 General ...................................................................................................................... 5 2 Standard Com position ............................................................................................. 5 3 Main Feat ures ........................................................................... ...
-
JAI CV-M77 - page 4
CV-M77 12.2.4 Patterned Noise .............................................................................................................. 27 12.3 References ..................................................................................................................... .... 27 13 Users Re cord ............................................... ...
-
JAI CV-M77 - page 5
CV-M77 1 General The CV-M77 camera is a compact RGB color progressive scan camera designed for automated imaging applications. The 1/3" CCD sensor with square pixels and primary mosaic filter offers a superb image quality and the build in DSP assures high color reproduction. The camera incorporates several triggered modes and various shutter f ...
-
JAI CV-M77 - page 6
CV-M77 4 Camera Housing and Dimensions SW1 (0.3) (3.54) (1.02) (1.02) (19.7) (19.7) (0.2) (0.2) (1.57) (1.97) 1 (C-Mount) 4-M3 depth5 4-M3 depth5 26 5 50 7.6 90 5 50 26 40 50 SYNC / RGB DC IN TRIG RS-232C MG B R 2 (CCD chip) 7 6 4 3 5 8 11 Figure 4-1 1 Lens mount of C-mount type. *1) 2 1/3" interline transfer CCD progressive scan sensor with s ...
-
JAI CV-M77 - page 7
CV-M77 5 Pin Assignment 3 4 5 6 7 8 9 10 11 12 1 2 5.1 12-pin Multi-conn ector (DC-IN/SYNC.) Type: HR10A-10R-12PB-01 (Hirose male) Seen from rear. Pin No. 5.1.1.1 Signal 5.1.1.2 Remarks 1 5.1.1.3 GND 2 +12V DC input 3 GND 4 NC 5 GND 6* Ext.HD input SW-S301.1 “ON” for 75 Ω termination, SW-S303.1 “ OFF” for HD output 7* Ext.VD input SW-S301 ...
-
JAI CV-M77 - page 8
CV-M77 See section 8 “Switch Settings” and section 9 “Jum per Settings ” for more information. *) When using the WEN signal from the 6 pin connector do not use the sam e signal from the 9 pin connector. *) Signals shown in bold italics are factory setting s. 5.3 9-pin DSUB-connector (RGB/SYNC.) Pin No. 5.3.1.1 Signal 5.3.1.2 Remarks 1* NC V ...
-
JAI CV-M77 - page 9
CV-M77 5.4 Input and Output Circuits In the following schematic diagrams the input and output circuits for video and timing signals are shown. For alternative connections refer to “I nternal Switch and Jumper Settings”. Jumper settings are shown as for factory default. 5.4.1 Video input The video output signal is a 75 Ω RGB video signal. The ...
-
JAI CV-M77 - page 10
CV-M77 6 Functions and Operation Apart from the standard continuous operation, the CV-M77 features three external triggering modes, Edge Pre-select, Pulse Width Control mode and Readout Delay mode. These 3 external triggering modes operate with H non-reset. In H non-reset, the exposure will be synchronized to the internal HD and the exposure will s ...
-
JAI CV-M77 - page 11
CV-M77 time (accumulation time) is governed by the fixed shutter speed set up by the rear panel DIP- switches or via RS-232C control. The resulting video signal will start to be read out a fter the selected shutter time. The WEN pulse indicates the start of valid video signal. Refer to timing charts for details. A new trigger pulse must not be appl ...
-
JAI CV-M77 - page 12
CV-M77 Set SW1-5 and SW1-6 on the rear plate of the camera to “ON” and SW1-7 to OFF or use the RS 232C control to set-up the PWC mode of the camera. 6.3.3 Frame-delay Readout Mode This trigger mode operates in H non-reset mode. In H non-reset mode the trigger and HD is synchronized. The exposure will start at the first HD pulse after the fallin ...
-
JAI CV-M77 - page 13
CV-M77 6.4 Timing diagram for Horizontal a nd Vertical Sync. Video Output - 13 - ...
-
JAI CV-M77 - page 14
CV-M77 6.5 Timing diagram for Edge Pre-select mode 1H=50.8 µ s Exposure time 0.5H 1.5H-2.5H 2H Min 4H 770H Effective video 4H 17H 9H 0.5H Exposure time 1.5H-2.5H 2H Min TRIG EXT HD INT VD EEN INT HD WEN Video out 6.6 Timing diagram for Pulse Width Control mode 1H=50.8 µ s 1H Min 0.5H-1.5H 0.5H Exposure period 4H 770H Effective video 4H 17H 0.5H E ...
-
JAI CV-M77 - page 15
CV-M77 6.8 Timing diagram for Long Time Exposure mode 1H=50.8 µ s 1H Max 4H 4H 1V x N (2VD Min) Exposure time 770H 17H 9H 1H Max EXT HD EXT VD INT VD EEN WEN Video out Remarks: 1VD indicates 792H. The interval of EXT VD input has to be multiple number of 1VD. EEN is lov INT VD - 15 - ...
-
JAI CV-M77 - page 16
CV-M77 7 Configuring the camera using the serial interface. 7.1 Mode Setting using ASCII commands via the RS-232C port. The configuration of the CV-M77 camera can be done via the RS-232C port. The camera is to be set up via an ASCII terminal or from a PC running terminal emulator software. Below is the description of the ASCII based short command p ...
-
JAI CV-M77 - page 17
CV-M77 C - Gain and ana logue signals se ttings. 1 AGC switch AS=[Param.]<CR><LF> AS?<CR><LF> 0=OFF (Manual), 1=ON (Auto) 2 Master gain level GA=[Param.]<CR><LF> GA?<CR><LF> 0-700 Available when AS=0. 3 Red gain level RG=[Param.]<CR><LF> RG?<CR><LF> 0-255 Available when WB=0. 4 ...
-
JAI CV-M77 - page 18
CV-M77 Response to firmware version request command Example: Request Command (PC → Camera) Command Name Format Receiving Data(Camera → PC) Remarks Version Request VN?<CR>< LF> ***<CR><LF> *** is Version No. (3 letter) 7.4 RS232C Cable Connections 1 TXD 2 RXD 3 GND 1 CD 4 DTR 6 DSR 2 RXD 3 TXD 5 GND 7 RTS 8 CTS 9 CI 9 PIN ...
-
JAI CV-M77 - page 19
CV-M77 8 Switch Settings Before changing any switch settings or jumper settings turn off the power. 8.1 Mode Settings by Switch The factory setting for the SW-1 switch on the rear panel of the camera is OFF: The electronic shutter is OFF, the external trigger modes ar e OFF, gamma is OFF (=1.0), the AGC is OFF and the RS-232C control is disabled. S ...
-
JAI CV-M77 - page 20
CV-M77 The SW301 switches (1-3) in “ON” position activates 75 Ω termination of ext.HD and ext.VD signals and it activates 75 Ω termination of an ext.trigger signal. The factory setting is “OFF” enabling TTL signal termination for all three signals. 8.2.2 SW302 switch S302 OFF ON White - 1 xxxx Balance 2 xxxx Sync. on G: 3 xxxx WEN: 4 xx ...
-
JAI CV-M77 - page 21
CV-M77 9 Jumper settings Before changing any switch settings or jumper settings turn off the power. 9.1 Jumper locations The jumpers are located on two boards, the PK8309A board and the PK8308A board: TK11333BU 2SC4667Y S.4 (BR) (BR) 2SC4617 R 2SC4 617R 1SS302 1SS302 2SC3265Y 02CZ7.5Z D1FS4 (LA) 2SA1681 (LA) 2SA1681 CHY KE-10T(1A) SC103 T10/10 SC10 ...
-
JAI CV-M77 - page 22
CV-M77 9.2 Jumper table Jumper settings versus connector pin configuration. Pin# Function JP301 JP302 JP303 JP304 JP305 JP306 JP307 JP308 JP309 JP310 JP311 JP312 JP401 JP402 12-pin Hirose connector 6 Ext. HD input Short 6 Int. HD output Short 7 Ext. VD input Open Short Open 7 Ext. VD output Open S h o r t 9 NC Open 9 PCLK output Short Open 10 WEN O ...
-
JAI CV-M77 - page 23
CV-M77 10 CV-M77 Camera Control Tool The Camera Control Tool software for the CV-M77 camera is available from the JAI homepage (www.jai.com). The software runs under Windows 98, NT and Windows 2000. The software interface has incorporated all the commands described in the ASCII protocol in an easy to use fashion – more user-friendly for some than ...
-
JAI CV-M77 - page 24
CV-M77 Fig. Windows from the Camera Control Tools software. - 24 - ...
-
JAI CV-M77 - page 25
CV-M77 11 Specifications Scanning system Progressive 792 lines 24.8 frames/sec . Pixel clock 25.000 MHz Line frequency 19.685 kHz (1270 pixel clock/li ne) Frame rate 24.8 frames/sec. (792 lines/frame) CCD sensor 1/3” RGB primary color IT CCD Sensing area 4.8 (h) x 3.6 (v) mm Effective pixels 1034 (h) x 779 (v) Pixels in video output 1028 (h) x 77 ...
-
JAI CV-M77 - page 26
CV-M77 11.1 Spectral sensitivity W a v e l e n g t h ( n m ) 400 5 00 600 7 00 800 1. 0 0. 8 0. 6 0. 4 0. 2 0. 0 R e l at i ve r e sp onse IR s t o p B G R - 26 - ...
-
JAI CV-M77 - page 27
CV-M77 12 Appendix 12.1 Precautions Personnel not trained in dealing with similar electr onic devices should not service this camera. The camera contains components sensitive to electrostatic discharge. Th e handling of these devices should follow the requirements of electrostatic sensitive components. Do not attempt to disassemble this camera. Do ...
-
JAI CV-M77 - page 28
CV-M77 13 Users Record Camera type: CV-M77 Revision: (Revision A) Serial No. …………….. Users Mode Settings Users Modifications 14 Index No index. - 28 - ...
¿Tienes una pregunta acerca de JAI CV-M77?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con JAI CV-M77, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con JAI CV-M77 probablemente compartirá una forma de solucionarlo.