JAI CV-M77の取扱説明書

28ページ 1.13 mb
ダウンロード

ページに移動 of 28

Summary
  • JAI CV-M77 - page 1

    CV-M77 Progressive Scan Camera CV-M77 Operation Manual Camera: Revision A Manual: Version 1.0 - 1 - ...

  • JAI CV-M77 - page 2

    CV-M77 - 2 - ...

  • JAI CV-M77 - page 3

    CV-M77 1 General ...................................................................................................................... 5 2 Standard Com position ............................................................................................. 5 3 Main Feat ures ........................................................................... ...

  • JAI CV-M77 - page 4

    CV-M77 12.2.4 Patterned Noise .............................................................................................................. 27 12.3 References ..................................................................................................................... .... 27 13 Users Re cord ............................................... ...

  • JAI CV-M77 - page 5

    CV-M77 1 General The CV-M77 camera is a compact RGB color progressive scan camera designed for automated imaging applications. The 1/3" CCD sensor with square pixels and primary mosaic filter offers a superb image quality and the build in DSP assures high color reproduction. The camera incorporates several triggered modes and various shutter f ...

  • JAI CV-M77 - page 6

    CV-M77 4 Camera Housing and Dimensions SW1 (0.3) (3.54) (1.02) (1.02) (19.7) (19.7) (0.2) (0.2) (1.57) (1.97) 1 (C-Mount) 4-M3 depth5 4-M3 depth5 26 5 50 7.6 90 5 50 26 40 50 SYNC / RGB DC IN TRIG RS-232C MG B R 2 (CCD chip) 7 6 4 3 5 8 11 Figure 4-1 1 Lens mount of C-mount type. *1) 2 1/3" interline transfer CCD progressive scan sensor with s ...

  • JAI CV-M77 - page 7

    CV-M77 5 Pin Assignment 3 4 5 6 7 8 9 10 11 12 1 2 5.1 12-pin Multi-conn ector (DC-IN/SYNC.) Type: HR10A-10R-12PB-01 (Hirose male) Seen from rear. Pin No. 5.1.1.1 Signal 5.1.1.2 Remarks 1 5.1.1.3 GND 2 +12V DC input 3 GND 4 NC 5 GND 6* Ext.HD input SW-S301.1 “ON” for 75 Ω termination, SW-S303.1 “ OFF” for HD output 7* Ext.VD input SW-S301 ...

  • JAI CV-M77 - page 8

    CV-M77 See section 8 “Switch Settings” and section 9 “Jum per Settings ” for more information. *) When using the WEN signal from the 6 pin connector do not use the sam e signal from the 9 pin connector. *) Signals shown in bold italics are factory setting s. 5.3 9-pin DSUB-connector (RGB/SYNC.) Pin No. 5.3.1.1 Signal 5.3.1.2 Remarks 1* NC V ...

  • JAI CV-M77 - page 9

    CV-M77 5.4 Input and Output Circuits In the following schematic diagrams the input and output circuits for video and timing signals are shown. For alternative connections refer to “I nternal Switch and Jumper Settings”. Jumper settings are shown as for factory default. 5.4.1 Video input The video output signal is a 75 Ω RGB video signal. The ...

  • JAI CV-M77 - page 10

    CV-M77 6 Functions and Operation Apart from the standard continuous operation, the CV-M77 features three external triggering modes, Edge Pre-select, Pulse Width Control mode and Readout Delay mode. These 3 external triggering modes operate with H non-reset. In H non-reset, the exposure will be synchronized to the internal HD and the exposure will s ...

  • JAI CV-M77 - page 11

    CV-M77 time (accumulation time) is governed by the fixed shutter speed set up by the rear panel DIP- switches or via RS-232C control. The resulting video signal will start to be read out a fter the selected shutter time. The WEN pulse indicates the start of valid video signal. Refer to timing charts for details. A new trigger pulse must not be appl ...

  • JAI CV-M77 - page 12

    CV-M77 Set SW1-5 and SW1-6 on the rear plate of the camera to “ON” and SW1-7 to OFF or use the RS 232C control to set-up the PWC mode of the camera. 6.3.3 Frame-delay Readout Mode This trigger mode operates in H non-reset mode. In H non-reset mode the trigger and HD is synchronized. The exposure will start at the first HD pulse after the fallin ...

  • JAI CV-M77 - page 13

    CV-M77 6.4 Timing diagram for Horizontal a nd Vertical Sync. Video Output - 13 - ...

  • JAI CV-M77 - page 14

    CV-M77 6.5 Timing diagram for Edge Pre-select mode 1H=50.8 µ s Exposure time 0.5H 1.5H-2.5H 2H Min 4H 770H Effective video 4H 17H 9H 0.5H Exposure time 1.5H-2.5H 2H Min TRIG EXT HD INT VD EEN INT HD WEN Video out 6.6 Timing diagram for Pulse Width Control mode 1H=50.8 µ s 1H Min 0.5H-1.5H 0.5H Exposure period 4H 770H Effective video 4H 17H 0.5H E ...

  • JAI CV-M77 - page 15

    CV-M77 6.8 Timing diagram for Long Time Exposure mode 1H=50.8 µ s 1H Max 4H 4H 1V x N (2VD Min) Exposure time 770H 17H 9H 1H Max EXT HD EXT VD INT VD EEN WEN Video out Remarks: 1VD indicates 792H. The interval of EXT VD input has to be multiple number of 1VD. EEN is lov INT VD - 15 - ...

  • JAI CV-M77 - page 16

    CV-M77 7 Configuring the camera using the serial interface. 7.1 Mode Setting using ASCII commands via the RS-232C port. The configuration of the CV-M77 camera can be done via the RS-232C port. The camera is to be set up via an ASCII terminal or from a PC running terminal emulator software. Below is the description of the ASCII based short command p ...

  • JAI CV-M77 - page 17

    CV-M77 C - Gain and ana logue signals se ttings. 1 AGC switch AS=[Param.]<CR><LF> AS?<CR><LF> 0=OFF (Manual), 1=ON (Auto) 2 Master gain level GA=[Param.]<CR><LF> GA?<CR><LF> 0-700 Available when AS=0. 3 Red gain level RG=[Param.]<CR><LF> RG?<CR><LF> 0-255 Available when WB=0. 4 ...

  • JAI CV-M77 - page 18

    CV-M77 Response to firmware version request command Example: Request Command (PC → Camera) Command Name Format Receiving Data(Camera → PC) Remarks Version Request VN?<CR>< LF> ***<CR><LF> *** is Version No. (3 letter) 7.4 RS232C Cable Connections 1 TXD 2 RXD 3 GND 1 CD 4 DTR 6 DSR 2 RXD 3 TXD 5 GND 7 RTS 8 CTS 9 CI 9 PIN ...

  • JAI CV-M77 - page 19

    CV-M77 8 Switch Settings Before changing any switch settings or jumper settings turn off the power. 8.1 Mode Settings by Switch The factory setting for the SW-1 switch on the rear panel of the camera is OFF: The electronic shutter is OFF, the external trigger modes ar e OFF, gamma is OFF (=1.0), the AGC is OFF and the RS-232C control is disabled. S ...

  • JAI CV-M77 - page 20

    CV-M77 The SW301 switches (1-3) in “ON” position activates 75 Ω termination of ext.HD and ext.VD signals and it activates 75 Ω termination of an ext.trigger signal. The factory setting is “OFF” enabling TTL signal termination for all three signals. 8.2.2 SW302 switch S302 OFF ON White - 1 xxxx Balance 2 xxxx Sync. on G: 3 xxxx WEN: 4 xx ...

  • JAI CV-M77 - page 21

    CV-M77 9 Jumper settings Before changing any switch settings or jumper settings turn off the power. 9.1 Jumper locations The jumpers are located on two boards, the PK8309A board and the PK8308A board: TK11333BU 2SC4667Y S.4 (BR) (BR) 2SC4617 R 2SC4 617R 1SS302 1SS302 2SC3265Y 02CZ7.5Z D1FS4 (LA) 2SA1681 (LA) 2SA1681 CHY KE-10T(1A) SC103 T10/10 SC10 ...

  • JAI CV-M77 - page 22

    CV-M77 9.2 Jumper table Jumper settings versus connector pin configuration. Pin# Function JP301 JP302 JP303 JP304 JP305 JP306 JP307 JP308 JP309 JP310 JP311 JP312 JP401 JP402 12-pin Hirose connector 6 Ext. HD input Short 6 Int. HD output Short 7 Ext. VD input Open Short Open 7 Ext. VD output Open S h o r t 9 NC Open 9 PCLK output Short Open 10 WEN O ...

  • JAI CV-M77 - page 23

    CV-M77 10 CV-M77 Camera Control Tool The Camera Control Tool software for the CV-M77 camera is available from the JAI homepage (www.jai.com). The software runs under Windows 98, NT and Windows 2000. The software interface has incorporated all the commands described in the ASCII protocol in an easy to use fashion – more user-friendly for some than ...

  • JAI CV-M77 - page 24

    CV-M77 Fig. Windows from the Camera Control Tools software. - 24 - ...

  • JAI CV-M77 - page 25

    CV-M77 11 Specifications Scanning system Progressive 792 lines 24.8 frames/sec . Pixel clock 25.000 MHz Line frequency 19.685 kHz (1270 pixel clock/li ne) Frame rate 24.8 frames/sec. (792 lines/frame) CCD sensor 1/3” RGB primary color IT CCD Sensing area 4.8 (h) x 3.6 (v) mm Effective pixels 1034 (h) x 779 (v) Pixels in video output 1028 (h) x 77 ...

  • JAI CV-M77 - page 26

    CV-M77 11.1 Spectral sensitivity W a v e l e n g t h ( n m ) 400 5 00 600 7 00 800 1. 0 0. 8 0. 6 0. 4 0. 2 0. 0 R e l at i ve r e sp onse IR s t o p B G R - 26 - ...

  • JAI CV-M77 - page 27

    CV-M77 12 Appendix 12.1 Precautions Personnel not trained in dealing with similar electr onic devices should not service this camera. The camera contains components sensitive to electrostatic discharge. Th e handling of these devices should follow the requirements of electrostatic sensitive components. Do not attempt to disassemble this camera. Do ...

  • JAI CV-M77 - page 28

    CV-M77 13 Users Record Camera type: CV-M77 Revision: (Revision A) Serial No. …………….. Users Mode Settings Users Modifications 14 Index No index. - 28 - ...

メーカー JAI カテゴリー Security Camera

JAI CV-M77のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- CV-M77の取扱説明書
- JAIの製品カード
- パンフレット
- またはJAI CV-M77の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、JAI CV-M77の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、JAI CV-M77の取り付け説明書、サービスマニュアル、簡易説明書、またはJAI CV-M77のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、JAI CV-M77の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

JAI CV-M77デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがJAI CV-M77を使用するのを助ける技術的文書のことです。説明書は通常、全てのJAI CV-M77ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

JAIの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. JAI CV-M77の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははJAI CV-M77の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。JAI CV-M77に関してこのドキュメントで見つけることができる全てのヒントの目次
3. JAI CV-M77デバイスの基本機能を使うにあたってのヒント。 JAI CV-M77のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。JAI CV-M77に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるJAI CV-M77のメーカー/サービスへの連絡先に関する情報。

JAI CV-M77についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもJAI CV-M77の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがJAI CV-M77で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)