Español dropdown-ico

Manual de instrucciones Snapper GM2513H

24 de páginas 2.35 mb
Descargar

Pasar a la página of 24

Summary
  • Snapper GM2513H - page 1

    OPERA T OR’S MANU AL SIMPLICITY Mfg. No. Description 1694240 13HP Honda Walk-Behind Brush Mower 1694204 13HP Briggs Walk-Behind Brush Mower 1694205 13HP Kawasaki Walk-Behind Brush Mower FERRIS Mfg. No. Description 1694249 13HP Briggs Walk-Behind Brush Mower (BC25BE) 1694251 13HP Honda Walk-Behind Brush Mower (BC25H) GIANT-VAC Mfg. No. Description ...

  • Snapper GM2513H - page 2

    1 T roub leshooting, Adjustment and Service .....14 Chart .....................................................................14 Travel Control Adjustment ....................................16 Blade Clutch Adjustment .......................................17 Blade Brake Adjustment .......................................18 Mower Belt Adjustment .. ...

  • Snapper GM2513H - page 3

    2 SAFE OPERA TION PRA CTICES FOR W ALK-BEHIND MO WERS This cutting machine is capable of amputating hands and feet and throwing objects. Failure to observe the follow- ing safety instructions could result in serious injury or death. GENERAL OPERA TION • Read, understand, and follow all instructions on the machine and in the manual(s). Be thorough ...

  • Snapper GM2513H - page 4

    3 Safety Rules and Information SLOPE OPERA TION Slopes are a major factor related to slip and fall acci- dents, which can result in severe injury. All slopes require extra caution. If you feel uneasy on a slope, do not mow it. Do • Mow across the face of slopes; never up and down. Exercise extreme caution when changing direction on slopes. • Re ...

  • Snapper GM2513H - page 5

    4 Safety Rules & Information SER VICE AND MAINTENANCE • Use extra care in handling gasoline and other fuels. They are flammable and vapors are explosive. a) Use only an approved container. b) Never remove gas cap or add fuel with the engine running. Allow engine to cool before refu- eling. Do not smoke. c) Never refuel the unit indoors. • I ...

  • Snapper GM2513H - page 6

    5 Safety and Instructional Decals Decal - Warning (7028490) Important Safety Operating Instructions. Read and understand before operating machine Decal - Engine Throttle Control (7029167) Models - All mowers Decal - Blade Control, Engine Key Switch (7028349) Models - All mowers Decal - Traction Drive / Freewheel Lever (1725229) Models - All mowers ...

  • Snapper GM2513H - page 7

    6 Features & Controls Engine On/Starter Rotate this key switch to the ON position before pulling on the starter rope. If the mower is equipped with the optional electric start- ing system, rotate the key past the ON position to engage the starter. When the engine starts, release the key. Throttle Contr ol The throttle controls engine speed. Mov ...

  • Snapper GM2513H - page 8

    7 Operating the Mower Engage Disengage Figure 4 - Traction Drive / Freewheel Control ST AR TING THE ENGINE NOTE - The procedures outlined within this section are general guidelines, and are in no way meant to replace or supercede engine manufacturer's operating instruc- tions. In order to obtain optimum performance from your engine, refer to y ...

  • Snapper GM2513H - page 9

    8 Operating the Mower T o Pr opel Unit Forward: • Grasping both upper handle/safety bar (A, Figure 5) and lower portion of traction drive engagement bar (B) with both hands, slowly begin squeezing engage- ment bar up toward handle. The unit should begin moving forward. T o Pr opel Unit In Reverse: • Grasping both upper handle/safety bar (A, Fig ...

  • Snapper GM2513H - page 10

    9 Operating the Mower OFF RUN ST ART A Figure 7 - PTO Engaged A. Blade Engagement Lever in engaged position. OFF RUN ST ART A Figure 8 - PTO Disengaged A. Blade Engagement Lever in the disengaged posi- tion. ENGA GING/DISENGA GING THE CUTTING BLADE To Engage Cutting Blade: • Push Blade Engagement Lever forward and then to the right until lever lo ...

  • Snapper GM2513H - page 11

    10 Operating the Mower A D C C B Figure 9 - Adjusting Height A. Skid B. Capscrew C. Washer D. Nut T O ADJUST CUTTING HEIGHT The front skids on the brush cutter have 3 sets of holes (Figure 9) for height adjustment: – Top holes - 3 1 / 4 " cutting depth – Center holes - 4" cutting depth – Bottom holes - 4 3 / 4 " cutting depth ? ...

  • Snapper GM2513H - page 12

    11 Regular Maintenance LUBRICA TION Service Interval: Every 25 Hours Lubricate the unit at the locations shown in Figure 10 as well as the lubrication points listed. Generally, all moving parts should be oiled where contact is made with other parts. Keep oil and grease off belts and pulleys. Wipe surfaces clean before and after lubrication. Grease: ...

  • Snapper GM2513H - page 13

    12 Regular Maintenance TIRE PRESSURE Tire pressure is 20 psi (1.4 bar). B A TTER Y SER VICE Cleaning the Battery and Cables - 9HP Models Service Interval: Every 100 Hours 1. Disconnect the cables from the battery, negative cable first (C, Figure 13a). 2. Remove the battery hold-down (B), rubber protective sheet (D) and battery (A). 3. Clean the bat ...

  • Snapper GM2513H - page 14

    13 Regular Maintenance SER VICING THE MO WER BLADES Service Interval: Every 100 Hours or As Required 1. Raise the front end of the brush mower and securely support in the raised position. 2. Blades should be sharp and free of nicks and dents. If worn or damaged, replace the blades as described in following steps. 3. To remove the blade, use a wood ...

  • Snapper GM2513H - page 15

    14 T roubleshooting, Adjustment, & Service TR OUBLESHOO TING PROBLEM CAUSE REMEDY Engine will not turnover or start. 1. PTO lever in the engaged position. Place in disengaged position. 2. Out of fuel. If the engine is hot, allow it to cool, then refill the fuel tank. 3. Engine flooded. Disengage choke. 4. Battery terminals require cleaning. See ...

  • Snapper GM2513H - page 16

    15 T roubleshooting, Adjustment & Service T r oubleshooting Cont. Blade will not engage. 1. Blade clutch rod too loose. See Blade Clutch Adjustment Section. 2. Blade belt worn or broken. Turn off engine and inspect belt. Adjust or replace as required. 3. Over-stretched or broken spring Turn off engine and inspect spring. Replace on blade clutch ...

  • Snapper GM2513H - page 17

    16 T roubleshooting, Adjustment, & Service TRA VEL CONTROL ADJUSTMENT Serial Number 0-011903999 1. The Travel Control engagement bars (A, Figure 16a) should be an equal distance from the Upper Handle Bar. If they are not, adjust their position. 2. Loosen the wing nut locknut (D) and rotate control rod (C) until engagement bars are properly adju ...

  • Snapper GM2513H - page 18

    17 T roubleshooting, Adjustment, & Service A D C B E Figure 17 - Blade Clutch Adjustment A. Clutch Rod B. Clutch Rod Lever C. Clutch Rod Fitting D. Locknut E. Hairpin Clip BLADE CLUTCH ADJUSTMENT If the mower blade does not stop running when the blade clutch lever is in the DISENGAGED position, does not run at full speed, adjust the Blade Clutc ...

  • Snapper GM2513H - page 19

    18 T roubleshooting, Adjustment, & Service BLADE BRAKE ADJUSTMENT The mower blade should stop within 5 seconds after the Blade Engagement Lever is moved to the DISEN- GAGED position. This adjustment is checked by: 1. Remove blade clutch cover plate (A, Figure 19). 2. Start engine. 3. With mower blade engagement lever in the DISEN- GAGED positio ...

  • Snapper GM2513H - page 20

    19 T roubleshooting, Adjustment, & Service A D B 1/8” Max. C Figure 21 - Traction Drive Belt Adjustment A. Transmission Pulley B. Drive Belt C. Engine Pulley D. Idler Pulley Figure 22 - Traction Drive Belt Adjustment A. Adjustment Nut TRA CTION DRIVE BEL T ADJUSTMENT If the mower drive is not functioning properly, the drive belt may need to b ...

  • Snapper GM2513H - page 21

    20 T roubleshooting, Adjustment & Service E D G F B C A Figure 24 - Belt Alignment A. Blade Drive Pulley B. Mower Belt C. Mower Tension Idler D. Transmission Pulley E. Transmission Belt F. Engine Pulley G. Transmission Tension Idler MO WER BEL T REPLA CEMENT To replace the mower blade drive belt; NOTE - The traction drive belt will have to be r ...

  • Snapper GM2513H - page 22

    21 Specifications Parts & Accessories ENGINEl BRIGGS HONDA KAWASAKI BRIGGS Engine 13 HP B&S 13 HP Honda 15 HP V-twin 16 HP B&S Transmission Hydro/Variable Hydro/Variable Hydro/Variable Hydro/Variable Ground Speed (mph) Infinite (.01 - 6) Infinite (.01 - 6) Infinite (.01 - 6) Infinite (.01 - 6) Weight (lbs) 287 298 299 N/A Overall Length ...

  • Snapper GM2513H - page 23

    22 Notes ...

  • Snapper GM2513H - page 24

    Products, Inc. 535 Macon Street/PO Box 777 McDonough, GA 30253 © Copyright 2003 Snapper Products, Inc. All Rights Reserved. Printed in USA. ...

Fabricante Snapper Categoría Lawn Mower

Los documentos del dispositivo Snapper GM2513H que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Snapper
- manuales de instrucciones GM2513H
- hojas de producto Snapper
- folletos informativos
- o etiquetas energéticas Snapper GM2513H
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Snapper GM2513H.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Snapper GM2513H, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Snapper GM2513H. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Snapper GM2513H.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Snapper GM2513H, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Snapper GM2513H. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Snapper GM2513H.

El manual de instrucciones completo de Snapper debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Snapper GM2513H - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Snapper GM2513H, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Snapper GM2513H que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Snapper GM2513H - que deben facilitarnos los primeros pasos durante el uso de Snapper GM2513H
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Snapper GM2513H
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Snapper GM2513H en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Snapper GM2513H?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Snapper GM2513H, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Snapper GM2513H probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Captcha
Nueva imagen

Comentarios (0)