Italiano dropdown-ico

Manuale per l’uso Snapper GM2513H

24 pagine 2.35 mb
Scarica

Vai alla pagina of 24

Summary
  • Snapper GM2513H - page 1

    OPERA T OR’S MANU AL SIMPLICITY Mfg. No. Description 1694240 13HP Honda Walk-Behind Brush Mower 1694204 13HP Briggs Walk-Behind Brush Mower 1694205 13HP Kawasaki Walk-Behind Brush Mower FERRIS Mfg. No. Description 1694249 13HP Briggs Walk-Behind Brush Mower (BC25BE) 1694251 13HP Honda Walk-Behind Brush Mower (BC25H) GIANT-VAC Mfg. No. Description ...

  • Snapper GM2513H - page 2

    1 T roub leshooting, Adjustment and Service .....14 Chart .....................................................................14 Travel Control Adjustment ....................................16 Blade Clutch Adjustment .......................................17 Blade Brake Adjustment .......................................18 Mower Belt Adjustment .. ...

  • Snapper GM2513H - page 3

    2 SAFE OPERA TION PRA CTICES FOR W ALK-BEHIND MO WERS This cutting machine is capable of amputating hands and feet and throwing objects. Failure to observe the follow- ing safety instructions could result in serious injury or death. GENERAL OPERA TION • Read, understand, and follow all instructions on the machine and in the manual(s). Be thorough ...

  • Snapper GM2513H - page 4

    3 Safety Rules and Information SLOPE OPERA TION Slopes are a major factor related to slip and fall acci- dents, which can result in severe injury. All slopes require extra caution. If you feel uneasy on a slope, do not mow it. Do • Mow across the face of slopes; never up and down. Exercise extreme caution when changing direction on slopes. • Re ...

  • Snapper GM2513H - page 5

    4 Safety Rules & Information SER VICE AND MAINTENANCE • Use extra care in handling gasoline and other fuels. They are flammable and vapors are explosive. a) Use only an approved container. b) Never remove gas cap or add fuel with the engine running. Allow engine to cool before refu- eling. Do not smoke. c) Never refuel the unit indoors. • I ...

  • Snapper GM2513H - page 6

    5 Safety and Instructional Decals Decal - Warning (7028490) Important Safety Operating Instructions. Read and understand before operating machine Decal - Engine Throttle Control (7029167) Models - All mowers Decal - Blade Control, Engine Key Switch (7028349) Models - All mowers Decal - Traction Drive / Freewheel Lever (1725229) Models - All mowers ...

  • Snapper GM2513H - page 7

    6 Features & Controls Engine On/Starter Rotate this key switch to the ON position before pulling on the starter rope. If the mower is equipped with the optional electric start- ing system, rotate the key past the ON position to engage the starter. When the engine starts, release the key. Throttle Contr ol The throttle controls engine speed. Mov ...

  • Snapper GM2513H - page 8

    7 Operating the Mower Engage Disengage Figure 4 - Traction Drive / Freewheel Control ST AR TING THE ENGINE NOTE - The procedures outlined within this section are general guidelines, and are in no way meant to replace or supercede engine manufacturer's operating instruc- tions. In order to obtain optimum performance from your engine, refer to y ...

  • Snapper GM2513H - page 9

    8 Operating the Mower T o Pr opel Unit Forward: • Grasping both upper handle/safety bar (A, Figure 5) and lower portion of traction drive engagement bar (B) with both hands, slowly begin squeezing engage- ment bar up toward handle. The unit should begin moving forward. T o Pr opel Unit In Reverse: • Grasping both upper handle/safety bar (A, Fig ...

  • Snapper GM2513H - page 10

    9 Operating the Mower OFF RUN ST ART A Figure 7 - PTO Engaged A. Blade Engagement Lever in engaged position. OFF RUN ST ART A Figure 8 - PTO Disengaged A. Blade Engagement Lever in the disengaged posi- tion. ENGA GING/DISENGA GING THE CUTTING BLADE To Engage Cutting Blade: • Push Blade Engagement Lever forward and then to the right until lever lo ...

  • Snapper GM2513H - page 11

    10 Operating the Mower A D C C B Figure 9 - Adjusting Height A. Skid B. Capscrew C. Washer D. Nut T O ADJUST CUTTING HEIGHT The front skids on the brush cutter have 3 sets of holes (Figure 9) for height adjustment: – Top holes - 3 1 / 4 " cutting depth – Center holes - 4" cutting depth – Bottom holes - 4 3 / 4 " cutting depth ? ...

  • Snapper GM2513H - page 12

    11 Regular Maintenance LUBRICA TION Service Interval: Every 25 Hours Lubricate the unit at the locations shown in Figure 10 as well as the lubrication points listed. Generally, all moving parts should be oiled where contact is made with other parts. Keep oil and grease off belts and pulleys. Wipe surfaces clean before and after lubrication. Grease: ...

  • Snapper GM2513H - page 13

    12 Regular Maintenance TIRE PRESSURE Tire pressure is 20 psi (1.4 bar). B A TTER Y SER VICE Cleaning the Battery and Cables - 9HP Models Service Interval: Every 100 Hours 1. Disconnect the cables from the battery, negative cable first (C, Figure 13a). 2. Remove the battery hold-down (B), rubber protective sheet (D) and battery (A). 3. Clean the bat ...

  • Snapper GM2513H - page 14

    13 Regular Maintenance SER VICING THE MO WER BLADES Service Interval: Every 100 Hours or As Required 1. Raise the front end of the brush mower and securely support in the raised position. 2. Blades should be sharp and free of nicks and dents. If worn or damaged, replace the blades as described in following steps. 3. To remove the blade, use a wood ...

  • Snapper GM2513H - page 15

    14 T roubleshooting, Adjustment, & Service TR OUBLESHOO TING PROBLEM CAUSE REMEDY Engine will not turnover or start. 1. PTO lever in the engaged position. Place in disengaged position. 2. Out of fuel. If the engine is hot, allow it to cool, then refill the fuel tank. 3. Engine flooded. Disengage choke. 4. Battery terminals require cleaning. See ...

  • Snapper GM2513H - page 16

    15 T roubleshooting, Adjustment & Service T r oubleshooting Cont. Blade will not engage. 1. Blade clutch rod too loose. See Blade Clutch Adjustment Section. 2. Blade belt worn or broken. Turn off engine and inspect belt. Adjust or replace as required. 3. Over-stretched or broken spring Turn off engine and inspect spring. Replace on blade clutch ...

  • Snapper GM2513H - page 17

    16 T roubleshooting, Adjustment, & Service TRA VEL CONTROL ADJUSTMENT Serial Number 0-011903999 1. The Travel Control engagement bars (A, Figure 16a) should be an equal distance from the Upper Handle Bar. If they are not, adjust their position. 2. Loosen the wing nut locknut (D) and rotate control rod (C) until engagement bars are properly adju ...

  • Snapper GM2513H - page 18

    17 T roubleshooting, Adjustment, & Service A D C B E Figure 17 - Blade Clutch Adjustment A. Clutch Rod B. Clutch Rod Lever C. Clutch Rod Fitting D. Locknut E. Hairpin Clip BLADE CLUTCH ADJUSTMENT If the mower blade does not stop running when the blade clutch lever is in the DISENGAGED position, does not run at full speed, adjust the Blade Clutc ...

  • Snapper GM2513H - page 19

    18 T roubleshooting, Adjustment, & Service BLADE BRAKE ADJUSTMENT The mower blade should stop within 5 seconds after the Blade Engagement Lever is moved to the DISEN- GAGED position. This adjustment is checked by: 1. Remove blade clutch cover plate (A, Figure 19). 2. Start engine. 3. With mower blade engagement lever in the DISEN- GAGED positio ...

  • Snapper GM2513H - page 20

    19 T roubleshooting, Adjustment, & Service A D B 1/8” Max. C Figure 21 - Traction Drive Belt Adjustment A. Transmission Pulley B. Drive Belt C. Engine Pulley D. Idler Pulley Figure 22 - Traction Drive Belt Adjustment A. Adjustment Nut TRA CTION DRIVE BEL T ADJUSTMENT If the mower drive is not functioning properly, the drive belt may need to b ...

  • Snapper GM2513H - page 21

    20 T roubleshooting, Adjustment & Service E D G F B C A Figure 24 - Belt Alignment A. Blade Drive Pulley B. Mower Belt C. Mower Tension Idler D. Transmission Pulley E. Transmission Belt F. Engine Pulley G. Transmission Tension Idler MO WER BEL T REPLA CEMENT To replace the mower blade drive belt; NOTE - The traction drive belt will have to be r ...

  • Snapper GM2513H - page 22

    21 Specifications Parts & Accessories ENGINEl BRIGGS HONDA KAWASAKI BRIGGS Engine 13 HP B&S 13 HP Honda 15 HP V-twin 16 HP B&S Transmission Hydro/Variable Hydro/Variable Hydro/Variable Hydro/Variable Ground Speed (mph) Infinite (.01 - 6) Infinite (.01 - 6) Infinite (.01 - 6) Infinite (.01 - 6) Weight (lbs) 287 298 299 N/A Overall Length ...

  • Snapper GM2513H - page 23

    22 Notes ...

  • Snapper GM2513H - page 24

    Products, Inc. 535 Macon Street/PO Box 777 McDonough, GA 30253 © Copyright 2003 Snapper Products, Inc. All Rights Reserved. Printed in USA. ...

Fabbricante Snapper Categoria Lawn Mower

I documenti che otteniamo dal fabbricante del dispositivoSnapper GM2513H possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Snapper
- manuali per l’uso GM2513H
- schede prodotto Snapper
- opuscoli
- o etichette energetiche Snapper GM2513H
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Snapper GM2513H.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Snapper GM2513H, manuali di manutenzione, brevi manuali o manuali utente Snapper GM2513H. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Snapper GM2513H.

Manuali per l’uso simili

Manuale completo del dispositivo Snapper GM2513H, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Snapper GM2513H dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Snapper GM2513H.

Il manuale per l’uso completo Snapper, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Snapper GM2513H - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Snapper GM2513H, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Snapper GM2513H che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Snapper GM2513H - che ci dovrebbe aiutare nei primi passi durante l'uso Snapper GM2513H
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Snapper GM2513H
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Snapper GM2513H in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Snapper GM2513H?

Utilizza il modulo sottostante

Se non hai risolto il problema con Snapper GM2513H con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Snapper GM2513H è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)