-
Pelco EH3515 - page 1
® INST ALLA TION EH3508/EH3512/EH3515 Series Environmental Enclosure C478M-M (1/06) ...
-
Pelco EH3515 - page 2
...
-
Pelco EH3515 - page 3
C478M-M (1/06) 3 Important Safety Instructions Prior to installation and use of this product, the following W ARNINGS should be observed. 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Only use attachments/accessories specifi ed by the manufacturer. 6. Use only with the cart, stand, tri ...
-
Pelco EH3515 - page 4
4 C478M-M (1/06) Description The EH3508/EH3512/EH3515 Series are indoor/outdoor light-duty camera enclosures designed for use with various cameras on the market and accommodate fi xed focal length or motorized zoom lenses, with or without auto-iris operation. The lid of the enclosure is hinged in the front providing easy access during installation ...
-
Pelco EH3515 - page 5
C478M-M (1/06) 5 Installation The following items are supplied to mount the enclosure: 2 1/4-20 x 0.500-inch hex head screws 2 Flat washers 2 Split washers The following items are supplied to mount the camera: 2 1/4-20 x 0.375-inch Phillips screws Figure 1. Package Contents HEX HEAD SCREWS FLAT WASHERS SPLIT WASHERS PHILLIPS SCREWS NUTS AND GLANDS ...
-
Pelco EH3515 - page 6
6 C478M-M (1/06) Figure 2. Exploded View of EH3500 Series Assembly FLAT WASHER SPLIT WASHER HEX HEAD SCREW EM1450 WALL MOUNT (NOT SUPPLIED) GLANDS PHILLIPS SCREWS CAMERA SLED SLED MOUNTING SCREWS ...
-
Pelco EH3515 - page 7
C478M-M (1/06) 7 Perform the following steps to install the enclosure, camera, and lens: 1. Unlatch and open the lid. 2. Remove the camera sled from the rail of the enclosure. a. Loosen the screws that hold the camera sled in place. b. Slide the sled forward so it can be lifted out over the screws. c. Remove the sled. d. Remove the parts bag tied t ...
-
Pelco EH3515 - page 8
8 C478M-M (1/06) 9. If the enclosure has accessories that require power, you will need to access the PC board. T o remove the cover, insert a screwdriver into the slot on top of the cover and lift the cover off. Connect the power for the accessories to pins 1 and 2 on the PC board (refer to Figures 4, 5, and 6 for information about accessory wiring ...
-
Pelco EH3515 - page 9
C478M-M (1/06) 9 Figure 4. EH3508-1/-2/-3 Wiring Diagram 1 2 3 4 5 6 7 8 9 10 HEA TER DEFROSTER INPUT , AC HIGH INPUT , AC LOW (NEUTRAL) 24/120/230 V AC MODELS ...
-
Pelco EH3515 - page 10
10 C478M-M (1/06) Figure 5. EH3512 Series Wiring Diagram NOTE: Blower applies to -1/-2/-3 models only. 1 2 3 4 5 6 7 8 9 10 HEA TER DIODE BRIDGE INPUT , AC HIGH INPUT , AC LOW (NEUTRAL) 24 V AC MODEL DEFROSTER BLOWER RED BLK RED BLK CAP 1 2 3 4 5 6 7 8 9 10 INPUT , AC HIGH INPUT , AC LOW (NEUTRAL) 230 V AC MODEL DEFROSTER HEA TER 120 V AC BLOWER RE ...
-
Pelco EH3515 - page 11
C478M-M (1/06) 11 Figure 6. EH3515 Series Wiring Diagram NOTE: Blower applies to -1/-2/-3 models only. 1 2 3 4 5 6 7 8 9 10 INPUT , AC HIGH INPUT , AC LOW (NEUTRAL) 120 V AC MODEL DEFROSTER BLOWER REAR HEA TER FRONT HEA TER 1 2 3 4 5 6 7 8 9 10 DIODE BRIDGE INPUT , AC HIGH INPUT , AC LOW (NEUTRAL) 24 V AC MODEL DEFROSTER BLOWER RED BLK RED BLK CAP ...
-
Pelco EH3515 - page 12
12 C478M-M (1/06) T able A. Enclosure Accessory Wiring Distances The following cable sizs are the minimum recommended for sue with the heater and defroster combination in enclosures in the EH3508 Series, and the heater, defroster , and blower combination in enclosures in the EH3512 Series and Eh3515 Series only . WARNING: When using a single power ...
-
Pelco EH3515 - page 13
C478M-M (1/06) 13 T able A. Enclosure Accessory Wiring Distances (Continued) Model Number Input V oltage Accessories Max. Power Consumption Cable Size Cable Distance EH3515-3 230 VAC at 50 Hz Heater Defroster Blower* 43 watts 20 AWG 18 AWG 16 AWG 14 AWG 6,473 ft (1,973 m) 10,291 ft (2,137 m) 16,365 ft (4,988 m) 26,019 ft (7,931 m) EH3515-1HD 120 VA ...
-
Pelco EH3515 - page 14
14 C478M-M (1/06) Example: An enclosure that requires 30 VA and is installed 94 feet (28 m) from the transformer would require a minimum wire gauge of 20 A WG. NOTE: Distances are calculated in feet; values in parentheses are meters . *Minimum Cable Requirements 75 Ohms Impendance All-copper center conductor All-copper braided shield with 95% braid ...
-
Pelco EH3515 - page 15
C478M-M (1/06) 15 Operation If your enclosure has a thermostatically controlled heater, the thermostat is set to turn on at 50°F (10°C) and to turn off at 80°F (27°C). If your enclosure has a blower and/or defroster, they operate continuously. MAINTENANCE Regularly scheduled maintenance prolongs the operational life and appearance of the equipm ...
-
Pelco EH3515 - page 16
16 C478M-M (1/06) Specifications Camera Mounting Multiple holes on adjustable camera sled; camera sled mounts in threaded strip for easier removal and can be inverted for additional camera elevation Camera and Lens Size Accommodates camera and lens combinations (including BNC connector) up to 2.87” W x 3.00” H (7.28 x 7.62 cm) and the followin ...
-
Pelco EH3515 - page 17
C478M-M (1/06) 17 Figure 7. EH3508, EH3512, EH3515 Dimension Drawing 5.14 (13.05) 3.88 (9.86) 2.00 (5.08) A B C EH3512 EH3515 A 14.75 (37.47) 17.75 (45.09) B 12.75 (32.38) 15.75 (40.00) C 1 1.25 (28.57) 14.25 (36.20) EH3508 10.75 (27.30) 8.75 (22.22) 7.32 (18.59) NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES. This equipment con ...
-
Pelco EH3515 - page 18
18 C478M-M (1/06) REVISION HISTORY Manual # Date Comments C478M-J 6/99 Moved the EH3508 Series enclosures from manual C1435M-A. Updated the description, installation instructions, and specifications. Updated wiring diagrams and dimension drawing. Modified per ECO 99-4749, which changed heater and defroster design. C478M-K 7/99 Incorporated addend ...
-
Pelco EH3515 - page 19
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products. • Three years on Genex ® Series p ...
-
Pelco EH3515 - page 20
® Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.com ISO 9001 United States | Canada | United Kingdom | The Netherlands | Singapore | Spain | Scandinavia | France | Middle East ...
¿Tienes una pregunta acerca de Pelco EH3515?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Pelco EH3515, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Pelco EH3515 probablemente compartirá una forma de solucionarlo.