-
AEG 502 D - page 1
502 D Extractor Hood Installation and Operating Instructions ...
-
AEG 502 D - page 2
3 Contents Electrical connections .......................................................... 4 Safety w ar nings f or electricians .............................................. 4 Appliances with 2 wires .......................................................... 5 Safety w ar nings f or kitchen unit installer ................................ 6 Gene ...
-
AEG 502 D - page 3
4 It must be ensured that the voltage and current indicated on the rating plate agree with the voltage of the user to electricity supply. If the appliance has been equipped with a mains lead with a moulded-on type plug, the following regulations must be comply with: The plug moulded on to the lead incorporates a fuse. For replacement, use a 5 amp B ...
-
AEG 502 D - page 4
5 The appliance must be connected to fix ed wir ing with a double pole s witched fused spur outlet with or without pilot lamp . W e strongly recommend the appliance to be connected only b y a qualified electrician who is a member of the NICEIC who will comply with the IEE and an y local regulations. NO TE: The ter minology “DOUBLE POLE” means t ...
-
AEG 502 D - page 5
6 When the unit is used in its extractor version, a sufficiently large ventilation hole must be provided, with dimensions that are approximately the same as the outlet hole. The air outlet must not be connected to chimney flues or combus- tion gas ducts. The air outlet must under no circumstances be connected to ventilation ducts for rooms in which ...
-
AEG 502 D - page 6
7 When used as an extractor unit, the hood must be fitted with a 100mm diameter hose. If the fumes must be forced out through the wall, you must obtain a MKZ sizable wall exhaust pipe (with external exhaust and air intake), E-Nr.- 610 899 004 (Ø 120 mm) which is one of our optional parts. When installing the hood, make sure you respect the follow- ...
-
AEG 502 D - page 7
8 Cooking vapours are cleaned by the charcoal filter (Special accessories) and ducted back into the kitchen. The AEG original KF-Plus charcoal filter is necessary for the recirculating mode (see paragraph “Special accessories”). For the recirculating mode proceed as follows: a) Remove the grid by turning knob A (fig. 2). b) Position the filter ...
-
AEG 502 D - page 8
9 Description of the appliance 1) Light switch 2) Motor switch 3) Work surface lamp 4) Grid 4 3 Technical details Model 502 D Net weight: 5 kg Height 145 mm Width 520 mm Depth 285 mm Absorbed power: 160W Motor: 1 x 120 W Lighting: 1 x 40 Watt Lengt of the cable: 110 cm Fan powers (speed), speed in compliance with DIN 44971 Speed: 1 2 3 Extractor ve ...
-
AEG 502 D - page 9
10 After having adjusted the hood for the version required, it may be installed. This appliance is designed for fitting in a cabinet or some other support. The opening to be made on the bottom of the wall-hung cabinet must correspond with the measurements shown in fig. 4 (495 X 260 mm). To fix the hood proceed as follows: a) remove the grid. b) Fit ...
-
AEG 502 D - page 10
11 The hood is fitted with one variable speed motor. The most effective use of the hood is obtained by switching it on a few minutes before you start cooking and leaving it on a for approximately 5-15 minutes after having finished, thus ensuring that all that cooking odours are eliminated. Never leave a cooking hob or ring on without a pot or pan o ...
-
AEG 502 D - page 11
12 Hood Operation A B The hood is fitted with a variable speed motor. The most effective use of the hood is obtained by switching it on a few minutes before you start cooking and leaving it on a for approximately 15 minutes after you have finished, thus ensuring all cooking odours are eliminated. The control switches are located on the unit’s fro ...
-
AEG 502 D - page 12
13 Before performing any maintenance operation, disconnect the hood from the electricity. The hood has a metal grease filter. To clean the filter, proceed as follows: Open the grill by turning knob A (fig. 2). Pull the two plastic stops B as shown by the arrows (fig. 5) and remove the metal filter. You should take out the metal filter every four we ...
-
AEG 502 D - page 13
14 The charcoal filter must be changed at least every 4 months. The charcoal filter cannot be washed or regenerated. The hood can only work well in the recirculating mode if the AEG recommended filter has been used, the filter is changed as recommended in this section and if the hood is cleaned and maintained as instructed in this booklet. Therefor ...
-
AEG 502 D - page 14
15 Always turn off the electricity before replacing lamps! 1) Remove the grid (Fig. 2) in order to check the lamps and replace them if necessary. 2) Unscrew the lamps that do not work and replace them with 40W max lamps (E14). If the light does not function, check that the lamps are properly screwed before contacting a customers’ service centre. ...
-
AEG 502 D - page 15
16 See AEG price-list for wallbox and hose accessories. KF-Plus charcoal filter E-Nr. 942 118 620 Technical assistance service You are welcome to telephone our technical assistance service (see list of technical assistance centres) whenever you need information or in the unlikely event of a fault. When calling, please be ready to specify: 1. The mo ...
-
AEG 502 D - page 16
AEG Hausgeräte AG Postfach 1036 D-90327 Nürnberg © Copyright by AEG H 259 226 140 L 650A ...
¿Tienes una pregunta acerca de AEG 502 D?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con AEG 502 D, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con AEG 502 D probablemente compartirá una forma de solucionarlo.