-
Hunter Kensington - page 1
www .HunterF an.com 1.888.830.1326 PA G E 7 PA G E 13 PA G E 14 PA G E 10 PA G E 5 PA G E 17 PA G E 6 30 inches 7 feet PA G E 2 What to Expect with Y our Installation Ceiling Br acket Installation Ladder PA G E 3 T ools Needed Wiring Canop y Maintenanc e & Cleaning Blades T roubleshooting Downrod Swit ch Housing Light Kit Prepar ation T able of ...
-
Hunter Kensington - page 2
www .HunterF an.com 1.888.830.1326 M0001-01 • 08/03/12 • © Hunter F an Company 1.888.830.1326 1.888.830.1326 What t o Expec t with Y our Installation Know your wiring If you are unfamiliar with wiring, use a qualied electrician. Y ou may need a friend to help you. Check box to see fan weight Assess location 30 inches from blade tip to neare ...
-
Hunter Kensington - page 3
T ools Needed Po wer Drill (optional) Ladder 9/64” Drill Bit (optional) Screwdrivers Pliers Wire Strippers Mounting Options 1. Y ou will need a Longer Downrod sold separately 2. Y ou may need an Angle Mounting Kit sold separately Use the 3 steps belo w to determine if your c eiling angle is greater than 34° 34 O OPTION 1 Flat OPTION 2 Angled 2 3 ...
-
Hunter Kensington - page 4
1.888.830.1326 www .HunterF an.com 4 Mounting Options (c ontinued) Use Standard or L ow-Prole Mounting to hang the fan from a at ceiling by a standard downrod (included). Use Angled Mounting t o hang the fan from a vault ed or angled ceiling (see previous page). Suppor t Str uc tur e Standard Mounting Styl e Ceiling Outlet Box (required) Supp ...
-
Hunter Kensington - page 5
1.888.830.1326 www .HunterF an.com C eiling Bracket Installa tion OFF Make sure all four (4) bumpers are still attached . F or angled ceilings, point opening toward peak. Refer to warning w .1 on pg. 2 T o av oid possible elec trical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box associ ...
-
Hunter Kensington - page 6
www .HunterF an.com 1.888.830.1326 C eiling Bracket Installa tion (continued) Prepar ation 1.888.830.1326 www .HunterF an.com D I S C A R D K E E P ! Remove the shipping blocks from the motor . Sav e the ve scre ws. The y will be needed for blade iron installation. Time Sav er Tip: Get a helper to insert grommets, found in the hardware bag , int ...
-
Hunter Kensington - page 7
1.888.830.1326 Downrod Slid e Slid e 1 2 3 4 5 6 7 8 9 10 Sold Separately Included Longer Downrod for angled ceilings or ceilings 10’ or higher Shorter Downrod for fans installed close to ceiling Standard Downrod for ceilings 8-10’ high Option 1 Option 2 Option 3 skip to next page If you need a diff erent downrod length follo w these steps: Ste ...
-
Hunter Kensington - page 8
KEEP! 8” 3/8” C U T & S T R I P (not to scale) Remove the pre-installed setscrew so that the downrod can be inserted. Hand tighten the downrod (at least 4-5 full turns) until it stops. The wires can be cut, but leave at least 8” extending from the top of the downr od. Downrod (c ontinued) 8” 3/8” Tighten the setscrew with pliers. DO N ...
-
Hunter Kensington - page 9
1.888.830.1326 9 M0001-01 • 08/03/12 • © Hunter F an Compan y www .HunterF an.com Downrod (c ontinued) DO NO T PICK THE F AN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. Put the wires and do wnrod through the canopy . Let the canop y sit loosely on top of the fan. ...
-
Hunter Kensington - page 10
www .HunterF an.com 1.888.830.1326 Wiring F R O M F A N F R O M C E I L I N G B R A C K E T F R O M F A N Using an orange wire connector from the hardware bag , connect the 3 grounding wires (green, green/ yellow stripe , or bare copper) coming from the ceiling , downrod, and hanging bracket. (Grounding) Green/Y ellow Stripe Green/Y ellow Stripe Wh ...
-
Hunter Kensington - page 11
www .HunterF an.com 1.888.830.1326 11 M0001-01 • 08/03/12 • © Hunter F an Compan y Canop y Lift the canopy into place so that the screw holes are aligned . Position the canop y so that, when lifted into place , the canopy ts into the hanging bracket as shown. Screw Holes Insert the two canopy screws found in the hardwar e bag. No te: Fan st ...
-
Hunter Kensington - page 12
www .HunterF an.com 1.888.830.1326 Blades Y our blades are shielded with Dust Armor® which is a nanotechnology coating that repels dust. F or cleaning the fan, use soft brushes or cloths to prevent scratching . Cleaning agents ma y damage the nishes. 12 Insert grommets found in the hardware bag into the holes in the blades, then secure each bla ...
-
Hunter Kensington - page 13
www .HunterF an.com 1.888.830.1326 F eed the wire plug through the center hole of the upper switch housing , then wrap keyhole slots around the screws and twist counterclockwise. Screw two (2) housing assembly screws from the hardware bag halfwa y into the motor housing . I t does not matter which two screw holes you choose . Insert the third screw ...
-
Hunter Kensington - page 14
www .HunterF an.com 1.888.830.1326 Connect the plugs from the upper and lower switch housings . Mak e sure to line up the colored markings on the connectors. Partially install two of the switch housing screws found in the bag . Align the notches in the sides of the lower switch housing with the screws on the upper switch housing . T wist the lower ...
-
Hunter Kensington - page 15
www .HunterF an.com 1.888.830.1326 Light Kit (c ontinued) C ONGRA TULA TIONS! Y OU’RE DONE! Install the bulbs into the sockets. When necessary , replace with bulbs of same wattage. No te: Glass shade styl e and number of lights may vary . See next page for fan opera tion instruc tions. Connect a pull chain pendant to each of the short chains comi ...
-
Hunter Kensington - page 16
www .HunterF an.com 1.888.830.1326 M0001-01 • 08/03/12 • © Hunter F an Compan y 16 Maintenanc e & Cleaning The fan pull chain controls the speed: high, medium, low , and off . The light pull chain controls the light xture: on and off . T o switch the direc tion of air ow , mov e the reverse switch to the opposite position. ON T urn P ...
-
Hunter Kensington - page 17
www .HunterF an.com 1.888.830.1326 M0001-01 • 08/03/12 • © Hunter F an Compan y 17 T roubleshooting Exc essive wobbling • Tighten all of the blade and blade iron screws until they are snug . • T urn the power off , support the fan carefully , and check that the hanger ball is properly seated . • Use the provided balancing kit and instruc ...
¿Tienes una pregunta acerca de Hunter Kensington?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Hunter Kensington, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Hunter Kensington probablemente compartirá una forma de solucionarlo.