-
Cisco Systems MDS 9020 - page 1
CHAPTER Send documentation comments to mdsfeedbac k-doc@cisco.com 3-1 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 3 Initial Configuration This chapter describes how to initially conf igure switches so they can be accessed by other de vices. This chapter includes the following sections: • Starting a Cisco MDS ...
-
Cisco Systems MDS 9020 - page 2
Send documentation comments to mdsfeedbac k-doc@cisco.com 3-2 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Starting a Cisco MDS 9020 Fabric Switch Starting a Cisco MDS 9020 Fabric Switch The follo wing procedure is a revie w of the tasks you should hav e completed during hardware ...
-
Cisco Systems MDS 9020 - page 3
Send documentation comments to mdsfeedbac k-doc@cisco.com 3-3 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Initial Setup Routine Preparing to Configure the Switch Before you conf igure a Cisco MDS 9020 Fabric Switch for the f irst time, you need the following information: • Admi ...
-
Cisco Systems MDS 9020 - page 4
Send documentation comments to mdsfeedbac k-doc@cisco.com 3-4 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Initial Setup Routine Setup Options The setup scenario differs based on the subnet to which you are adding the ne w switch. Y ou must conf igure a Cisco MDS 9020 Fabric Switc ...
-
Cisco Systems MDS 9020 - page 5
Send documentation comments to mdsfeedbac k-doc@cisco.com 3-5 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Initial Setup Routine Assigning Setup Information This section describes how to initially conf igure the switch for both out-of-band and in-band management. Note Press Ctrl-C ...
-
Cisco Systems MDS 9020 - page 6
Send documentation comments to mdsfeedbac k-doc@cisco.com 3-6 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Initial Setup Routine Step 4 Enter yes (no is the default) to create additional accounts. Note Only the admin user name can create or modify user accounts. Create another log ...
-
Cisco Systems MDS 9020 - page 7
Send documentation comments to mdsfeedbac k-doc@cisco.com 3-7 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Initial Setup Routine Step 10 Enter no (no is the default) to disable the SSH service. Enabled SSH service? (yes/no) [n]: no Step 11 Enter no (no is the default) to not conf ...
-
Cisco Systems MDS 9020 - page 8
Send documentation comments to mdsfeedbac k-doc@cisco.com 3-8 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Initial Setup Routine Using the setup Command T o make changes to the initial conf iguration at a later time, you can enter the setup command in EXEC mode. Note The setup uti ...
-
Cisco Systems MDS 9020 - page 9
Send documentation comments to mdsfeedbac k-doc@cisco.com 3-9 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Accessing the Switch Accessing the Switch After initial conf iguration, you can access the switch in the following w ays: • Serial console access—Y ou can use a serial po ...
-
Cisco Systems MDS 9020 - page 10
Send documentation comments to mdsfeedbac k-doc@cisco.com 3-10 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Assigning a Switch Name Assigning a Switch Name Each switch in the fabric requires a unique name. Y ou can assign names to easily identify the switch by its physical locatio ...
-
Cisco Systems MDS 9020 - page 11
Send documentation comments to mdsfeedbac k-doc@cisco.com 3-11 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Configuring Date and Time Configuring Date and Time A Cisco MDS 9020 Fabric Switch uses Uni versal Coordinated T ime (UTC), which is the same as Greenwich Mean T ime (GMT). ...
-
Cisco Systems MDS 9020 - page 12
Send documentation comments to mdsfeedbac k-doc@cisco.com 3-12 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Configuring Date and Time Adjusting for Daylight Saving Time Follo wing U.S. standards, the switch can advance the clock one hour at 2:00 a.m. on the f irst Sunday in April ...
-
Cisco Systems MDS 9020 - page 13
Send documentation comments to mdsfeedbac k-doc@cisco.com 3-13 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Management Interface Configuration NTP Configuration A Network T ime Protocol (NTP) server provides a precise time source (radio clock or atomic clock) to synchronize the sy ...
-
Cisco Systems MDS 9020 - page 14
Send documentation comments to mdsfeedbac k-doc@cisco.com 3-14 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Management Interface Configuration Obtaining Remote Management Access In some cases, a switch interface might be administrati vely shut down. Y ou can check the status of an ...
-
Cisco Systems MDS 9020 - page 15
Send documentation comments to mdsfeedbac k-doc@cisco.com 3-15 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Default Gateway Configuration Default Gateway Configuration The switch sends IP packets with unresolved destination IP addresses to the def ault gateway . Figure 3-3 shows t ...
-
Cisco Systems MDS 9020 - page 16
Send documentation comments to mdsfeedbac k-doc@cisco.com 3-16 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Telnet Server Connection Telnet Server Connection The T elnet server is enabled by default on a Cisco MDS 9020 Fabric Switch. If you require a secure SSH connection, you nee ...
-
Cisco Systems MDS 9020 - page 17
Send documentation comments to mdsfeedbac k-doc@cisco.com 3-17 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Working with Configuration Files Displaying Configuration Files Use the show running-conf ig command to view the running conf iguration f ile. switch# show running-config ip ...
-
Cisco Systems MDS 9020 - page 18
Send documentation comments to mdsfeedbac k-doc@cisco.com 3-18 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Working with Configuration Files interface fc1/5 no shutdown Auto interface fc1/6 no shutdown Auto interface fc1/7 no shutdown Auto interface fc1/8 no shutdown Auto interfac ...
-
Cisco Systems MDS 9020 - page 19
Send documentation comments to mdsfeedbac k-doc@cisco.com 3-19 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Working with Configuration Files Downloading Configuration Files to the Switch Y ou can conf igure a Cisco MDS 9020 Fabric Switch by using conf iguration f iles that you cre ...
-
Cisco Systems MDS 9020 - page 20
Send documentation comments to mdsfeedbac k-doc@cisco.com 3-20 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Working with Configuration Files Saving the Configuration After you hav e created a running conf iguration in system memory , you can save it to the startup conf iguration i ...
-
Cisco Systems MDS 9020 - page 21
Send documentation comments to mdsfeedbac k-doc@cisco.com 3-21 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Deleting Files Rolling Back to a Previous Configuration All switch conf igurations reside in the internal bootf lash: f ile system. If your internal bootf lash: f ile system ...
-
Cisco Systems MDS 9020 - page 22
Send documentation comments to mdsfeedbac k-doc@cisco.com 3-22 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Deleting Files ...
¿Tienes una pregunta acerca de Cisco Systems MDS 9020?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Cisco Systems MDS 9020, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Cisco Systems MDS 9020 probablemente compartirá una forma de solucionarlo.