Cisco Systems MDS 9020の取扱説明書

22ページ 0.39 mb
ダウンロード

ページに移動 of 22

Summary
  • Cisco Systems MDS 9020 - page 1

    CHAPTER Send documentation comments to mdsfeedbac k-doc@cisco.com 3-1 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 3 Initial Configuration This chapter describes how to initially conf igure switches so they can be accessed by other de vices. This chapter includes the following sections: • Starting a Cisco MDS ...

  • Cisco Systems MDS 9020 - page 2

    Send documentation comments to mdsfeedbac k-doc@cisco.com 3-2 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Starting a Cisco MDS 9020 Fabric Switch Starting a Cisco MDS 9020 Fabric Switch The follo wing procedure is a revie w of the tasks you should hav e completed during hardware ...

  • Cisco Systems MDS 9020 - page 3

    Send documentation comments to mdsfeedbac k-doc@cisco.com 3-3 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Initial Setup Routine Preparing to Configure the Switch Before you conf igure a Cisco MDS 9020 Fabric Switch for the f irst time, you need the following information: • Admi ...

  • Cisco Systems MDS 9020 - page 4

    Send documentation comments to mdsfeedbac k-doc@cisco.com 3-4 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Initial Setup Routine Setup Options The setup scenario differs based on the subnet to which you are adding the ne w switch. Y ou must conf igure a Cisco MDS 9020 Fabric Switc ...

  • Cisco Systems MDS 9020 - page 5

    Send documentation comments to mdsfeedbac k-doc@cisco.com 3-5 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Initial Setup Routine Assigning Setup Information This section describes how to initially conf igure the switch for both out-of-band and in-band management. Note Press Ctrl-C ...

  • Cisco Systems MDS 9020 - page 6

    Send documentation comments to mdsfeedbac k-doc@cisco.com 3-6 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Initial Setup Routine Step 4 Enter yes (no is the default) to create additional accounts. Note Only the admin user name can create or modify user accounts. Create another log ...

  • Cisco Systems MDS 9020 - page 7

    Send documentation comments to mdsfeedbac k-doc@cisco.com 3-7 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Initial Setup Routine Step 10 Enter no (no is the default) to disable the SSH service. Enabled SSH service? (yes/no) [n]: no Step 11 Enter no (no is the default) to not conf ...

  • Cisco Systems MDS 9020 - page 8

    Send documentation comments to mdsfeedbac k-doc@cisco.com 3-8 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Initial Setup Routine Using the setup Command T o make changes to the initial conf iguration at a later time, you can enter the setup command in EXEC mode. Note The setup uti ...

  • Cisco Systems MDS 9020 - page 9

    Send documentation comments to mdsfeedbac k-doc@cisco.com 3-9 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Accessing the Switch Accessing the Switch After initial conf iguration, you can access the switch in the following w ays: • Serial console access—Y ou can use a serial po ...

  • Cisco Systems MDS 9020 - page 10

    Send documentation comments to mdsfeedbac k-doc@cisco.com 3-10 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Assigning a Switch Name Assigning a Switch Name Each switch in the fabric requires a unique name. Y ou can assign names to easily identify the switch by its physical locatio ...

  • Cisco Systems MDS 9020 - page 11

    Send documentation comments to mdsfeedbac k-doc@cisco.com 3-11 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Configuring Date and Time Configuring Date and Time A Cisco MDS 9020 Fabric Switch uses Uni versal Coordinated T ime (UTC), which is the same as Greenwich Mean T ime (GMT). ...

  • Cisco Systems MDS 9020 - page 12

    Send documentation comments to mdsfeedbac k-doc@cisco.com 3-12 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Configuring Date and Time Adjusting for Daylight Saving Time Follo wing U.S. standards, the switch can advance the clock one hour at 2:00 a.m. on the f irst Sunday in April ...

  • Cisco Systems MDS 9020 - page 13

    Send documentation comments to mdsfeedbac k-doc@cisco.com 3-13 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Management Interface Configuration NTP Configuration A Network T ime Protocol (NTP) server provides a precise time source (radio clock or atomic clock) to synchronize the sy ...

  • Cisco Systems MDS 9020 - page 14

    Send documentation comments to mdsfeedbac k-doc@cisco.com 3-14 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Management Interface Configuration Obtaining Remote Management Access In some cases, a switch interface might be administrati vely shut down. Y ou can check the status of an ...

  • Cisco Systems MDS 9020 - page 15

    Send documentation comments to mdsfeedbac k-doc@cisco.com 3-15 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Default Gateway Configuration Default Gateway Configuration The switch sends IP packets with unresolved destination IP addresses to the def ault gateway . Figure 3-3 shows t ...

  • Cisco Systems MDS 9020 - page 16

    Send documentation comments to mdsfeedbac k-doc@cisco.com 3-16 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Telnet Server Connection Telnet Server Connection The T elnet server is enabled by default on a Cisco MDS 9020 Fabric Switch. If you require a secure SSH connection, you nee ...

  • Cisco Systems MDS 9020 - page 17

    Send documentation comments to mdsfeedbac k-doc@cisco.com 3-17 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Working with Configuration Files Displaying Configuration Files Use the show running-conf ig command to view the running conf iguration f ile. switch# show running-config ip ...

  • Cisco Systems MDS 9020 - page 18

    Send documentation comments to mdsfeedbac k-doc@cisco.com 3-18 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Working with Configuration Files interface fc1/5 no shutdown Auto interface fc1/6 no shutdown Auto interface fc1/7 no shutdown Auto interface fc1/8 no shutdown Auto interfac ...

  • Cisco Systems MDS 9020 - page 19

    Send documentation comments to mdsfeedbac k-doc@cisco.com 3-19 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Working with Configuration Files Downloading Configuration Files to the Switch Y ou can conf igure a Cisco MDS 9020 Fabric Switch by using conf iguration f iles that you cre ...

  • Cisco Systems MDS 9020 - page 20

    Send documentation comments to mdsfeedbac k-doc@cisco.com 3-20 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Working with Configuration Files Saving the Configuration After you hav e created a running conf iguration in system memory , you can save it to the startup conf iguration i ...

  • Cisco Systems MDS 9020 - page 21

    Send documentation comments to mdsfeedbac k-doc@cisco.com 3-21 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Deleting Files Rolling Back to a Previous Configuration All switch conf igurations reside in the internal bootf lash: f ile system. If your internal bootf lash: f ile system ...

  • Cisco Systems MDS 9020 - page 22

    Send documentation comments to mdsfeedbac k-doc@cisco.com 3-22 Cisco MDS 9020 Fabric Switch Configuration Guide and Command Reference OL-6988-02 Chapter 3 Initial Configuration Deleting Files ...

メーカー Cisco Systems カテゴリー Switch

Cisco Systems MDS 9020のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- MDS 9020の取扱説明書
- Cisco Systemsの製品カード
- パンフレット
- またはCisco Systems MDS 9020の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Cisco Systems MDS 9020の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Cisco Systems MDS 9020の取り付け説明書、サービスマニュアル、簡易説明書、またはCisco Systems MDS 9020のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Cisco Systems MDS 9020の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Cisco Systems MDS 9020デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがCisco Systems MDS 9020を使用するのを助ける技術的文書のことです。説明書は通常、全てのCisco Systems MDS 9020ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Cisco Systemsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Cisco Systems MDS 9020の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははCisco Systems MDS 9020の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Cisco Systems MDS 9020に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Cisco Systems MDS 9020デバイスの基本機能を使うにあたってのヒント。 Cisco Systems MDS 9020のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Cisco Systems MDS 9020に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるCisco Systems MDS 9020のメーカー/サービスへの連絡先に関する情報。

Cisco Systems MDS 9020についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもCisco Systems MDS 9020の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCisco Systems MDS 9020で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)