-
Smarthome 7307 - page 1
T otal Protection Alarm System SMARTHOME™ #7307 PA T . D410633 Patents Pending SMARTHOME.COM™ 1-800-SMART-HOME 949-221-9200 http://www.smarthome.com Order #7307 ...
-
Smarthome 7307 - page 2
– 2 – Y our Guide to the T otal Protection Alarm System SMARTHOME™ #7307 – 3 – P ACKAGE CONTENTS........................................................................4 OVE R VIE W ....................................................................................... . 5 PLANNING YOUR HOME SECURITY NEEDS................................. ...
-
Smarthome 7307 - page 3
P ACKAGE CONTENTS Everything required for installation is included with this package 1 Control Panel (SC-001) includes: 1 antenna (installed) 1 AC adapter 1 9 volt alkaline battery T wo sets of Door/Window Sensors (WT-433), each set includes: 1 transmitter 1 magnetic switch 1 magnet 2 spacers 1 12 volt alkaline battery (installed) 1 Motion Sensor ( ...
-
Smarthome 7307 - page 4
– 6 – PLANNING YOUR HOME SECURITY NEEDS Before you begin to install your security system, analyze the premises to determine your security needs. Consider those doors and windows which are more likely to be used as points of entry by an intruder , the ones that are poorly lit or the entrances that can not be seen from the street. Sketch a map of ...
-
Smarthome 7307 - page 5
4. Attach the unit to the wall. If hanging the unit, insert two screws using the template provided. If screwing the back directly to the wall, take the back plate right off by prying apart one hinge. Use as much force as needed. The plastic hinge will not break. 5. Using the template, attach the backplate on to the wall with 4 screws. 6. Mount the ...
-
Smarthome 7307 - page 6
– 10 – (Cont. : Installing the motion sensor (PS-433) Set the switch on the side t o "TEST" and allow 60 seconds for the unit to warm up. ( when using test mode, a signal will not be sent to the Control Panel ). Now walk in the area you want the motion sensor to detect movement in. If movement is detected, the red light on the front o ...
-
Smarthome 7307 - page 7
LIGHTS AND SOUNDS If you make a mistake while programming, the Control Panel emits three short beeps. That means the system has cleared and you must start the pro- gramming sequence from the beginning. If you get lost in the programming sequence or have made a mistake and want to start over again, press the [ * ] on the key pad of the Control Panel ...
-
Smarthome 7307 - page 8
– 14 – ST ANDARD PROGRAMMING Option 2: Home Sequence - T o arm your system when someone remains in the premises. 1. Press the current MPIN [ 0 0 0 ]. 2. Press [ C ]. Y ou hear a long beep. The arm light and the red lights in zones 3 and 4 go on. Both the green and red lights flash in zone 1 for 45 seconds which gives you 45 seconds t o le ave t ...
-
Smarthome 7307 - page 9
– 16 – KEYCHAIN TRANSMITTER (4B-434) TO DISARM THE SYSTEM, OR DEACTIV A TE THE SIREN USING THE KEYCHAIN TRANSMITTER When the system is armed: Press button #3. The red light on the transmitter flashes and the Control Panel beeps twice. The system is now disarmed. When the siren is sounding: Press button #3. The red light on the transmitter flash ...
-
Smarthome 7307 - page 10
– 18 – SECONDAR Y PERSONAL IDENTIFICA TION NUMBER (SPIN) Y ou may want to give someone limited access to the system, (baby sitter , cleaner , repairman etc.). For this purpose the SC-100 provides you with the option of adding up to 3 separate SPIN. A SPIN can be any number of 3 digits or more. Y ou can use a SPIN to arm and disarm the system bu ...
-
Smarthome 7307 - page 11
– 20 – ADV ANCED PROGRAMMING T o program sensors to send their signals to a different zone, you must first clear them from communicating with their current zone. TO CLEAR A ZONE 1. Enter the current MPIN. 2. Press [ B ]. 3. Press the number key to identify current zone [ 1, 2, 3 or 4 ]. The zone light(s) will flash for eight seconds. 4. While t ...
-
Smarthome 7307 - page 12
– 23 – ADV ANCED PROGRAMMING 1. Enter the current MPIN. 2. Press [ A ]. 3. Press [ A ]. Y ou will hear a long beep. The arm light, the red and green lights in zones 1 and the red lights in zones 3 and 4 go on. Zone 1 has the entry delay to allow someone to enter through the front door and deactivate the system before the siren sounds. This opti ...
-
Smarthome 7307 - page 13
– 25 – Below is a table summarizing all the preprogrammed sequences. Sequence Zone 1 Zone 2 Zones 3 & 4 When sequence should be used FOR TESTIN G MPIN A # chime chime chime use for testing after installation and to test batteries, also use as a subtle chime when a remote sensor has been activated BASIC PRO GR AMMING MPIN B C exit delay off ...
-
Smarthome 7307 - page 14
– 27 – BA TTER Y MAINTENANCE MOTION SENSOR BA TTER Y The Motion Sensor operates on a 9 volt alkaline battery accessible beneath a sliding panel on the botto m of the unit. All re mote sensors come with the battery already installed. Disarm the Control Panel before replacing all batteries. When the battery level i s lo w , the Motion Sensor will ...
-
Smarthome 7307 - page 15
KEYCHAIN TRANSMITTER BA TTER Y The Keychain Transmitter operates on a 12 volt alkaline battery which is installed at the factory . There are two screws on the back of the transmitter that holds the case together . T o replace the Keychain T ransmitter battery: 1. Undo the two screws on the back of the transmitter . The back will then come off. 2. U ...
¿Tienes una pregunta acerca de Smarthome 7307?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Smarthome 7307, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Smarthome 7307 probablemente compartirá una forma de solucionarlo.