-
Impex MWB CR 4 - page 1
MARCY CORNER GYM CR 4 IMPEX FITNESS PRODUCTS 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999 - 8899 Fax: (626) 961 - 9966 www.impex - fitness.com info@impex - fitness.com NOTE: Please r ead all instructions carefully before using this product Safety Notice Hardware Identifier Assembly Instruction Parts List Resistance Chart How to U ...
-
Impex MWB CR 4 - page 2
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 HARDWARE IDENTIFIER .....…....................................................................... 3 ASSEMBLY INSTRUCTIONS........ ...
-
Impex MWB CR 4 - page 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the mac ...
-
Impex MWB CR 4 - page 4
3 ...
-
Impex MWB CR 4 - page 5
ASSEMBLY INSTRUCTION Tools Required to Assemb le the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended this machine be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Place the Right Base Frame (#1) and Left Base Frame (#2) on the floor, at a right angle to each other. Attach t ...
-
Impex MWB CR 4 - page 6
STEP 2 (See Diagram 2) A.) Attach the Right Upper Frame (#6) to the top of the Right Vertical Beam (#3). Secure it with two M10 x 2 ¾” Carriage Bolts (#90), one 4 ¾” x 2” Bracket (#38), two ∅ 3/4” Washers (#106), and two M10 Aircraft Nuts (#110). B.) A ttach the Left Upper Frame (#7) to the Left Vertical Beam (#4). Secure it with one M1 ...
-
Impex MWB CR 4 - page 7
6 ...
-
Impex MWB CR 4 - page 8
STEP 3 (See Diagram 3) A.) Attach the Seat Support Frame (#14) to the Right Vertical Beam (#3). Secure it with two M10 x 2 ¾” Carriage Bolts (#90), one 4 ¾” x 2” Bracket (#38), two ∅ ¾” Washers (#106) and two M10 Aircraft Nuts (#110). B.) Attach two Vertical Supports (#16) to the front of the Seat Support (#14). Secure them w ith two M ...
-
Impex MWB CR 4 - page 9
STEP 4 (See Diagram 4) A.) Attach four ∅ 1” x ½” Bushings (#55) to the Leg Press Pivot Arm (#18). Attach the Pivot Arm to the bracket on the Right Base Frame (#1). Secure it with one M12 x 3 1/8” Hex Head Bolt (#91), two ∅ 1” Washers (#105), and one M12 Aircraft Nut (#109). B.) Attach two ∅ 1”x1/2” Bushings (#55) to the tube on t ...
-
Impex MWB CR 4 - page 10
STEP 5 (See Diagram 5) A.) Insert the Chromed Adjustment Tube (#20) into the Leg Press Frame (#19). Secure it with a Quick Releas e Pin (#62). B.) Attach the Foot Plate (#21) to the Chromed Tube (#20) and secure it with a L - Shaped Pin (#112). C.) Attach the Bench Press Frame (#11) to the pivot tube on the Right Base Frame (#1). Insert a M10 x 8 5 ...
-
Impex MWB CR 4 - page 11
STEP 6 (See Diagram 6) A.) Attach the Butterfly Support Frame (#8) to the front of the Right Vertical Beam (#3). Attach the Butterfly Pulley Support (#113) to the back of the Right Vertical Beam (#3). Secure them with two M10 x 3” C arriage Bolts (#89), ∅ ¾” Washers (#106), and M10 Aircraft Nuts (#110). B.) Insert the axle on the Right Butte ...
-
Impex MWB CR 4 - page 12
STEP 7 (See Diagram 7) A.) Attach the Leg Developer Frame (#15) to the Left Vertical Beam (#4). Secure it with tw o M10 x 2 ¾” Carriage Bolts (#90), one 4 ¾” x 2” Bracket (#38), two ∅ ¾” Washers (#106), and two M10 Aircraft Nuts (#110). B.) Attach the Leg Developer Frame (#15) to the Left Base Frame (#2). Secure it with a M10 x 2 ¾” ...
-
Impex MWB CR 4 - page 13
STEP 8 (See Diagram 8) A.) Attach the Seat (#40) to the Leg Developer Frame (#15). Secure it with two ∅ 5/8” Washers (#107) and M8 x 2 ½” Allen Bolts (#101). B.) Attach both Left Handlebar (#32) and Right Handlebar (#33) to the Leg Deve loper Frame (#15) underneath the Seat (#40). Secure them with two M10 x 2 ¾” Carriage Bolts (#90), ∅ ...
-
Impex MWB CR 4 - page 14
STEP 9 (See Diagram 9 & 15) A.) Attach a Pulley (#58) to the bracket on the Right Butterfly Arm (#10). Secure it with one M10 x 1 ¾” Allen Bolt (#98), two ∅ ¾” Washers (#106), and one M10 Aircraft Nut (#110). Repeat to install another Pulley to the other side. B.) Attach one end of the 86” Butterfly Cable (#84) to the Right Butterfly ...
-
Impex MWB CR 4 - page 15
STEP 10 (See Diagram 10 & 15) A.) Attach the Ball - end of the 132” Upper Cable (#85) to the Right Upper Frame (#6). Install a Pulley (#58). Push two Bushings (#56) into the holes from both sides. Secure it with one M10 x 2 ½” Allen Bolt (#97) and M10 Aircraft Nut (#110). B.) Draw the Cable towards the back of the machine along the top of ...
-
Impex MWB CR 4 - page 16
STEP 11 (See Diagram 11 & 15) A.) Attach one end of the 327 ½” Leg Press Cable (#83) to the bracket on the Leg Press Pivot Arm (#18). (See C View) Secure it with one M10 x 1” Allen Bolt (#99), two ∅ ¾” Washers (#106), and one M10 Aircra ft Nut (#110). NOTE: Do not over tighten this bolt. Make sure the head of the cable can swivel on t ...
-
Impex MWB CR 4 - page 17
16 ...
-
Impex MWB CR 4 - page 18
STEP 12 (See Diagram 12 & 15) A.) Attach the Ball - end of the 158” Ab Cable (#86) to the opening on the Left Vertical Beam (#4). Install a Pulley (#58). Push two Bushings (#56) from both sides of the Beam. Secure it with a M10 x 2 ½” Allen Bolt (#97) and M10 Aircraft Nut (#110). B.) Draw the Cable over the Pulley downward and install anot ...
-
Impex MWB CR 4 - page 19
STEP 13 (See Diagram 13 & 15) A.) Attach the Ball - end of the 102” Leg Curl Cable (#87) to the opening on the Leg Developer (#23). Install a Pulley (#58) to the opening. Attach two Bushings (#56) to the h oles on the Leg Developer. Secure it with a M10 x 2 ½” Allen Bolt (#97) and M10 Aircraft Nut (#110). B.) Pull the Cable through the ope ...
-
Impex MWB CR 4 - page 20
STEP 14 (See Diagram 14 & 15) A.) Tighten all the nuts and bolts previously installed. B.) Before putting the Weight Plates on, now move the machine to the corner of the room or place where you will use the machine. C.) Lift up the Sel ector Rod and install the Weight Plates. To install the plates, hold the plate at an angle and place between t ...
-
Impex MWB CR 4 - page 21
20 ...
-
Impex MWB CR 4 - page 22
PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Right Base Frame 1 2 Left Base Frame 1 3 Right Vertical Beam 1 4 Left Vertical Beam 1 5 Rear Vertical Beam 1 6 Right U pper Frame 1 7 Left Upper Frame 1 8 Butterfly Support Frame 1 9 Left Butterfly 1 10 Right Butterfly 1 11 Bench Press Frame 1 12 Bench Press Handle 2 13 Vertical Press Frame 1 14 Seat Support ...
-
Impex MWB CR 4 - page 23
22 ...
-
Impex MWB CR 4 - page 24
HOW TO USE How to use the quick release connector. The Clip is removed from the Connector. Connector Clip Place the chain in between the connector and insert the Clip through the holes. Chain Insert Push down the Clip to secure. 23 ...
-
Impex MWB CR 4 - page 25
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from def ects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited ...
¿Tienes una pregunta acerca de Impex MWB CR 4?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Impex MWB CR 4, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Impex MWB CR 4 probablemente compartirá una forma de solucionarlo.