English dropdown-ico

Manual Impex MWB CR 4

25 pages 2.73 mb
Download

Go to site of 25

Summary
  • Impex MWB CR 4 - page 1

    MARCY CORNER GYM CR 4 IMPEX FITNESS PRODUCTS 14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746 Tel: (800) 999 - 8899 Fax: (626) 961 - 9966 www.impex - fitness.com info@impex - fitness.com NOTE: Please r ead all instructions carefully before using this product Safety Notice Hardware Identifier Assembly Instruction Parts List Resistance Chart How to U ...

  • Impex MWB CR 4 - page 2

    TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 HARDWARE IDENTIFIER .....…....................................................................... 3 ASSEMBLY INSTRUCTIONS........ ...

  • Impex MWB CR 4 - page 3

    IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the mac ...

  • Impex MWB CR 4 - page 4

    3 ...

  • Impex MWB CR 4 - page 5

    ASSEMBLY INSTRUCTION Tools Required to Assemb le the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended this machine be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Place the Right Base Frame (#1) and Left Base Frame (#2) on the floor, at a right angle to each other. Attach t ...

  • Impex MWB CR 4 - page 6

    STEP 2 (See Diagram 2) A.) Attach the Right Upper Frame (#6) to the top of the Right Vertical Beam (#3). Secure it with two M10 x 2 ¾” Carriage Bolts (#90), one 4 ¾” x 2” Bracket (#38), two ∅ 3/4” Washers (#106), and two M10 Aircraft Nuts (#110). B.) A ttach the Left Upper Frame (#7) to the Left Vertical Beam (#4). Secure it with one M1 ...

  • Impex MWB CR 4 - page 7

    6 ...

  • Impex MWB CR 4 - page 8

    STEP 3 (See Diagram 3) A.) Attach the Seat Support Frame (#14) to the Right Vertical Beam (#3). Secure it with two M10 x 2 ¾” Carriage Bolts (#90), one 4 ¾” x 2” Bracket (#38), two ∅ ¾” Washers (#106) and two M10 Aircraft Nuts (#110). B.) Attach two Vertical Supports (#16) to the front of the Seat Support (#14). Secure them w ith two M ...

  • Impex MWB CR 4 - page 9

    STEP 4 (See Diagram 4) A.) Attach four ∅ 1” x ½” Bushings (#55) to the Leg Press Pivot Arm (#18). Attach the Pivot Arm to the bracket on the Right Base Frame (#1). Secure it with one M12 x 3 1/8” Hex Head Bolt (#91), two ∅ 1” Washers (#105), and one M12 Aircraft Nut (#109). B.) Attach two ∅ 1”x1/2” Bushings (#55) to the tube on t ...

  • Impex MWB CR 4 - page 10

    STEP 5 (See Diagram 5) A.) Insert the Chromed Adjustment Tube (#20) into the Leg Press Frame (#19). Secure it with a Quick Releas e Pin (#62). B.) Attach the Foot Plate (#21) to the Chromed Tube (#20) and secure it with a L - Shaped Pin (#112). C.) Attach the Bench Press Frame (#11) to the pivot tube on the Right Base Frame (#1). Insert a M10 x 8 5 ...

  • Impex MWB CR 4 - page 11

    STEP 6 (See Diagram 6) A.) Attach the Butterfly Support Frame (#8) to the front of the Right Vertical Beam (#3). Attach the Butterfly Pulley Support (#113) to the back of the Right Vertical Beam (#3). Secure them with two M10 x 3” C arriage Bolts (#89), ∅ ¾” Washers (#106), and M10 Aircraft Nuts (#110). B.) Insert the axle on the Right Butte ...

  • Impex MWB CR 4 - page 12

    STEP 7 (See Diagram 7) A.) Attach the Leg Developer Frame (#15) to the Left Vertical Beam (#4). Secure it with tw o M10 x 2 ¾” Carriage Bolts (#90), one 4 ¾” x 2” Bracket (#38), two ∅ ¾” Washers (#106), and two M10 Aircraft Nuts (#110). B.) Attach the Leg Developer Frame (#15) to the Left Base Frame (#2). Secure it with a M10 x 2 ¾” ...

  • Impex MWB CR 4 - page 13

    STEP 8 (See Diagram 8) A.) Attach the Seat (#40) to the Leg Developer Frame (#15). Secure it with two ∅ 5/8” Washers (#107) and M8 x 2 ½” Allen Bolts (#101). B.) Attach both Left Handlebar (#32) and Right Handlebar (#33) to the Leg Deve loper Frame (#15) underneath the Seat (#40). Secure them with two M10 x 2 ¾” Carriage Bolts (#90), ∅ ...

  • Impex MWB CR 4 - page 14

    STEP 9 (See Diagram 9 & 15) A.) Attach a Pulley (#58) to the bracket on the Right Butterfly Arm (#10). Secure it with one M10 x 1 ¾” Allen Bolt (#98), two ∅ ¾” Washers (#106), and one M10 Aircraft Nut (#110). Repeat to install another Pulley to the other side. B.) Attach one end of the 86” Butterfly Cable (#84) to the Right Butterfly ...

  • Impex MWB CR 4 - page 15

    STEP 10 (See Diagram 10 & 15) A.) Attach the Ball - end of the 132” Upper Cable (#85) to the Right Upper Frame (#6). Install a Pulley (#58). Push two Bushings (#56) into the holes from both sides. Secure it with one M10 x 2 ½” Allen Bolt (#97) and M10 Aircraft Nut (#110). B.) Draw the Cable towards the back of the machine along the top of ...

  • Impex MWB CR 4 - page 16

    STEP 11 (See Diagram 11 & 15) A.) Attach one end of the 327 ½” Leg Press Cable (#83) to the bracket on the Leg Press Pivot Arm (#18). (See C View) Secure it with one M10 x 1” Allen Bolt (#99), two ∅ ¾” Washers (#106), and one M10 Aircra ft Nut (#110). NOTE: Do not over tighten this bolt. Make sure the head of the cable can swivel on t ...

  • Impex MWB CR 4 - page 17

    16 ...

  • Impex MWB CR 4 - page 18

    STEP 12 (See Diagram 12 & 15) A.) Attach the Ball - end of the 158” Ab Cable (#86) to the opening on the Left Vertical Beam (#4). Install a Pulley (#58). Push two Bushings (#56) from both sides of the Beam. Secure it with a M10 x 2 ½” Allen Bolt (#97) and M10 Aircraft Nut (#110). B.) Draw the Cable over the Pulley downward and install anot ...

  • Impex MWB CR 4 - page 19

    STEP 13 (See Diagram 13 & 15) A.) Attach the Ball - end of the 102” Leg Curl Cable (#87) to the opening on the Leg Developer (#23). Install a Pulley (#58) to the opening. Attach two Bushings (#56) to the h oles on the Leg Developer. Secure it with a M10 x 2 ½” Allen Bolt (#97) and M10 Aircraft Nut (#110). B.) Pull the Cable through the ope ...

  • Impex MWB CR 4 - page 20

    STEP 14 (See Diagram 14 & 15) A.) Tighten all the nuts and bolts previously installed. B.) Before putting the Weight Plates on, now move the machine to the corner of the room or place where you will use the machine. C.) Lift up the Sel ector Rod and install the Weight Plates. To install the plates, hold the plate at an angle and place between t ...

  • Impex MWB CR 4 - page 21

    20 ...

  • Impex MWB CR 4 - page 22

    PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Right Base Frame 1 2 Left Base Frame 1 3 Right Vertical Beam 1 4 Left Vertical Beam 1 5 Rear Vertical Beam 1 6 Right U pper Frame 1 7 Left Upper Frame 1 8 Butterfly Support Frame 1 9 Left Butterfly 1 10 Right Butterfly 1 11 Bench Press Frame 1 12 Bench Press Handle 2 13 Vertical Press Frame 1 14 Seat Support ...

  • Impex MWB CR 4 - page 23

    22 ...

  • Impex MWB CR 4 - page 24

    HOW TO USE How to use the quick release connector. The Clip is removed from the Connector. Connector Clip Place the chain in between the connector and insert the Clip through the holes. Chain Insert Push down the Clip to secure. 23 ...

  • Impex MWB CR 4 - page 25

    IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from def ects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited ...

Manufacturer Impex Category Home Gym

Documents that we receive from a manufacturer of a Impex MWB CR 4 can be divided into several groups. They are, among others:
- Impex technical drawings
- MWB CR 4 manuals
- Impex product data sheets
- information booklets
- or energy labels Impex MWB CR 4
All of them are important, but the most important information from the point of view of use of the device are in the user manual Impex MWB CR 4.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Impex MWB CR 4, service manual, brief instructions and user manuals Impex MWB CR 4. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Impex MWB CR 4.

Similar manuals

A complete manual for the device Impex MWB CR 4, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Impex MWB CR 4 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Impex MWB CR 4.

A complete Impex manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Impex MWB CR 4 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Impex MWB CR 4, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Impex MWB CR 4, that we can find in the current document
3. Tips how to use the basic functions of the device Impex MWB CR 4 - which should help us in our first steps of using Impex MWB CR 4
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Impex MWB CR 4
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Impex MWB CR 4 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Impex MWB CR 4?

Use the form below

If you did not solve your problem by using a manual Impex MWB CR 4, ask a question using the form below. If a user had a similar problem with Impex MWB CR 4 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)