-
CDA HCG 931 - page 1
Customer Car e Department • The G r oup Ltd. • Harby Road • Langar • Nottinghamshi r e • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www .cda.eu GB HCG 93 1 .. - Built-in C ooking Hob Manual for Inst allation, Use and Maintenanc e ...
-
CDA HCG 931 - page 2
2 Important This appliance is designed and manufactur ed solely for the cooking of domestic (household) f ood and is not suitable for an y non domestic application and ther ef ore should not be used in a commercial envir onment. The applianc e guar antee will be void if the appliance is used within a non domestic envir onment i.e. a semi commer cia ...
-
CDA HCG 931 - page 3
3 Important Saf eguar ds and R ecommendations – Do not carry out any cleaning or maintenance without first disconnecting the appliance from the electrical supply. – During and after use of the hob, certain parts will bec ome very hot. Do not touc h hot parts. – After use alw ays ensur e that the contr ol knobs are in the “ ● ” OFF posi ...
-
CDA HCG 931 - page 4
4 Featur es and T echnical Data Fig. 1 Cooking P oints 1 . Auxiliary burner (A) - 1 ,00 kW 2. Semi-rapid burner (SR) - 1 ,75 kW 3. Rapid burner (R) - 3,00 kW 4. T riple ring burner (TR) - 3,50 kW Contr ol Panel 1 0. Right auxiliary burner (1) control knob 1 1 . Central auxiliary burner (1) contr ol knob 1 2. T riple ring burner (4) c ontrol knob 1 ...
-
CDA HCG 931 - page 5
5 How t o use the hob Gas burners Gas flow to the burners is adjust ed by turning the knobs (illustrated in fig.2) whic h contr ol the valves. T urning the knob so that the indicator line points to the symbols printed on the panel achiev es the following functions: – Symbol ● : T ap closed (burner off) – Symbol : High (maximum) – Symbol : ...
-
CDA HCG 931 - page 6
6 WRONG C ORRECT Choice o f Burner The s ymbols print ed on the panel by the side of the knob indicate which burner you ar e controlling. Choose a suitable burner depending on the cookwar e diameter and capacity. The pan diameter should be suitable for the burner power to make the most of the burner's high efficiency and not waste fuel. A sma ...
-
CDA HCG 931 - page 7
7 Cleaning and Maintenanc e Gener al Tips – Befor e cleaning the hob switc h it off and wait f or it to cool down. – Clean with a cloth, hot water and soap or liquid deter gent. – Do not use products whic h ar e abrasive, c orrosive or c hlorine based. – Do not use steel pads. – Av oid using cleaning products with a c hlorine or acidic ba ...
-
CDA HCG 931 - page 8
8 Fig. 8 Burners and Grids – These parts can be remov ed and cleaned with appropriat e products. – After cleaning, the burners and their flame spr eaders must be well dried and corr ectly r eplaced. – It is v ery important to c heck that the burner flame spreader and the cap have been corr ectly positioned. Failur e to do so can cause serio ...
-
CDA HCG 931 - page 9
9 Corr ect Position o f T riple Ring Burner The triple ring burner must be correctly positioned (see fig. 9); the burner ribs must be fitted in their housing as shown by the arrow . The burner corr ectly positioned must not rot ate (fig. 1 0). Then position the cap “ A ” and the ring “ B ” (figs. 1 0 - 1 1) A B Fig. 1 0 Fig. 1 1 Fig. 9 ...
-
CDA HCG 931 - page 10
10 TIPS FOR INS T ALLA TION Location – The appliance may be installed in a kitchen, Kitchen/diner or a bed sitting room, but not in a r oom or space containing a bath or a show er . – The appliance must not be installed in a bed-sit r oom of less than 20m 3 . – The appliance is designed and appr oved for domestic use only and should not be in ...
-
CDA HCG 931 - page 11
11 Installation T echnical Inf ormation for the Installer In or der to install the hob into the kitchen fixture, a hole with the dimensions shown in fig. 1 2 has to be made, bearing in mind the following: – within the unit, between the bottom of the hob and the upper surface of a shelf there must be a clearance of at least 30 mm. – It is abso ...
-
CDA HCG 931 - page 12
12 Fast ening the Installation Br ackets (fig. 1 5) – Each hob is pr ovided with an inst allation kit including brack ets and screws for fastening the top to fixtur e panels from 2 t o 4 cm thick. – T urn the hob upside down and fast en the br ack ets “ A ” to the appropriat e sock et holes, without tightening the scr ews “ B ” for th ...
-
CDA HCG 931 - page 13
13 Gas supply r equir ements Important Not e This appliance is supplied for use on NA TURAL GAS or LPG (chec k the gas regulation label attached on the appliance). – Appliances supplied for use on NA TURAL GAS: they are adjusted for this gas only and cannot be used on any other gas (LPG) without modification. The appliances ar e manufactur ed fo ...
-
CDA HCG 931 - page 14
14 Gas Connection The installation of the gas appliance to Natural Gas or LP Gas must be carried out by a suitably qualified and register ed installer . Installers shall take due account of the pr ovisions of the relev ant British Standar ds Code of Practice, the Gas Safety Regulations and the Building Standar ds (Scotland) (Consolidation) R egula ...
-
CDA HCG 931 - page 15
15 Gas connection Cat: II 2H3+ The fitting (fig. 1 7) is made up of: – 1 nut “ A ” – 1 elbow fitting “ C ” – gasket “ F ” Connection t o the Gas Supply – Be careful when flexible pipes ar e used that they do not come into contact with moving parts. – T o maintain the thickness of 3 cm, the hob is fit ted with a channel t ...
-
CDA HCG 931 - page 16
16 Con v er sion to Natur al Gas or LPG Replacing the Burner Inject ors – Remove the pan supports, the burner caps and flame speader s. – Using a wrenc h, substitute the nozzle injector s “ J ” (Figs. 1 9 - 20) with those most suitable for the kind of gas for whic h it is to be used. The burners ar e conceiv ed in such a wa y so as not to ...
-
CDA HCG 931 - page 17
17 Regulating the Burner Minimum Set ting When changing from one type of gas to another , the minimum tap output must also be correct, considering that in this position the flame must be about 4 mm long and must remain lit even when the knob is turned sharply from the maximum t o the minimum position. The adjustment is performed with the burner li ...
-
CDA HCG 931 - page 18
18 Mains Electricity Connection Incorr ect installation ma y be danger ous and the manufacturer can no t be held responsible. W arning! This appliance must be earthed The manufacturer declines all responsibility f or any problem caused b y failur e to observ e this rule. THIS APPLIANCE MUST BE C ONNECTED T O THE MAINS SUPPL Y B Y A CO MPETENT PERSO ...
-
CDA HCG 931 - page 19
19 Appliance Servicing CDA pr ovide a quality and effective after -sales service to cover all y our servicing needs. Please attac h your r eceipt to this page f or safekeeping. Please help us to help you by ha ving the following inf ormation available when booking a servic e-call: 1 . Model type, make and model – see the product data plat e. 2. E ...
-
CDA HCG 931 - page 20
Customer Car e Department • The G r oup Ltd. • Harby Road • Langar • Nottinghamshi r e • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www .cda.eu T o contact our Customer Car e Department, or for Service, please contact us on the det ails below . Cod. 1 1 03520/GB - ß4 ...
¿Tienes una pregunta acerca de CDA HCG 931?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con CDA HCG 931, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con CDA HCG 931 probablemente compartirá una forma de solucionarlo.