-
CDA HCG 931 - page 1
Customer Car e Department • The G r oup Ltd. • Harby Road • Langar • Nottinghamshi r e • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www .cda.eu GB HCG 93 1 .. - Built-in C ooking Hob Manual for Inst allation, Use and Maintenanc e ...
-
CDA HCG 931 - page 2
2 Important This appliance is designed and manufactur ed solely for the cooking of domestic (household) f ood and is not suitable for an y non domestic application and ther ef ore should not be used in a commercial envir onment. The applianc e guar antee will be void if the appliance is used within a non domestic envir onment i.e. a semi commer cia ...
-
CDA HCG 931 - page 3
3 Important Saf eguar ds and R ecommendations – Do not carry out any cleaning or maintenance without first disconnecting the appliance from the electrical supply. – During and after use of the hob, certain parts will bec ome very hot. Do not touc h hot parts. – After use alw ays ensur e that the contr ol knobs are in the “ ● ” OFF posi ...
-
CDA HCG 931 - page 4
4 Featur es and T echnical Data Fig. 1 Cooking P oints 1 . Auxiliary burner (A) - 1 ,00 kW 2. Semi-rapid burner (SR) - 1 ,75 kW 3. Rapid burner (R) - 3,00 kW 4. T riple ring burner (TR) - 3,50 kW Contr ol Panel 1 0. Right auxiliary burner (1) control knob 1 1 . Central auxiliary burner (1) contr ol knob 1 2. T riple ring burner (4) c ontrol knob 1 ...
-
CDA HCG 931 - page 5
5 How t o use the hob Gas burners Gas flow to the burners is adjust ed by turning the knobs (illustrated in fig.2) whic h contr ol the valves. T urning the knob so that the indicator line points to the symbols printed on the panel achiev es the following functions: – Symbol ● : T ap closed (burner off) – Symbol : High (maximum) – Symbol : ...
-
CDA HCG 931 - page 6
6 WRONG C ORRECT Choice o f Burner The s ymbols print ed on the panel by the side of the knob indicate which burner you ar e controlling. Choose a suitable burner depending on the cookwar e diameter and capacity. The pan diameter should be suitable for the burner power to make the most of the burner's high efficiency and not waste fuel. A sma ...
-
CDA HCG 931 - page 7
7 Cleaning and Maintenanc e Gener al Tips – Befor e cleaning the hob switc h it off and wait f or it to cool down. – Clean with a cloth, hot water and soap or liquid deter gent. – Do not use products whic h ar e abrasive, c orrosive or c hlorine based. – Do not use steel pads. – Av oid using cleaning products with a c hlorine or acidic ba ...
-
CDA HCG 931 - page 8
8 Fig. 8 Burners and Grids – These parts can be remov ed and cleaned with appropriat e products. – After cleaning, the burners and their flame spr eaders must be well dried and corr ectly r eplaced. – It is v ery important to c heck that the burner flame spreader and the cap have been corr ectly positioned. Failur e to do so can cause serio ...
-
CDA HCG 931 - page 9
9 Corr ect Position o f T riple Ring Burner The triple ring burner must be correctly positioned (see fig. 9); the burner ribs must be fitted in their housing as shown by the arrow . The burner corr ectly positioned must not rot ate (fig. 1 0). Then position the cap “ A ” and the ring “ B ” (figs. 1 0 - 1 1) A B Fig. 1 0 Fig. 1 1 Fig. 9 ...
-
CDA HCG 931 - page 10
10 TIPS FOR INS T ALLA TION Location – The appliance may be installed in a kitchen, Kitchen/diner or a bed sitting room, but not in a r oom or space containing a bath or a show er . – The appliance must not be installed in a bed-sit r oom of less than 20m 3 . – The appliance is designed and appr oved for domestic use only and should not be in ...
-
CDA HCG 931 - page 11
11 Installation T echnical Inf ormation for the Installer In or der to install the hob into the kitchen fixture, a hole with the dimensions shown in fig. 1 2 has to be made, bearing in mind the following: – within the unit, between the bottom of the hob and the upper surface of a shelf there must be a clearance of at least 30 mm. – It is abso ...
-
CDA HCG 931 - page 12
12 Fast ening the Installation Br ackets (fig. 1 5) – Each hob is pr ovided with an inst allation kit including brack ets and screws for fastening the top to fixtur e panels from 2 t o 4 cm thick. – T urn the hob upside down and fast en the br ack ets “ A ” to the appropriat e sock et holes, without tightening the scr ews “ B ” for th ...
-
CDA HCG 931 - page 13
13 Gas supply r equir ements Important Not e This appliance is supplied for use on NA TURAL GAS or LPG (chec k the gas regulation label attached on the appliance). – Appliances supplied for use on NA TURAL GAS: they are adjusted for this gas only and cannot be used on any other gas (LPG) without modification. The appliances ar e manufactur ed fo ...
-
CDA HCG 931 - page 14
14 Gas Connection The installation of the gas appliance to Natural Gas or LP Gas must be carried out by a suitably qualified and register ed installer . Installers shall take due account of the pr ovisions of the relev ant British Standar ds Code of Practice, the Gas Safety Regulations and the Building Standar ds (Scotland) (Consolidation) R egula ...
-
CDA HCG 931 - page 15
15 Gas connection Cat: II 2H3+ The fitting (fig. 1 7) is made up of: – 1 nut “ A ” – 1 elbow fitting “ C ” – gasket “ F ” Connection t o the Gas Supply – Be careful when flexible pipes ar e used that they do not come into contact with moving parts. – T o maintain the thickness of 3 cm, the hob is fit ted with a channel t ...
-
CDA HCG 931 - page 16
16 Con v er sion to Natur al Gas or LPG Replacing the Burner Inject ors – Remove the pan supports, the burner caps and flame speader s. – Using a wrenc h, substitute the nozzle injector s “ J ” (Figs. 1 9 - 20) with those most suitable for the kind of gas for whic h it is to be used. The burners ar e conceiv ed in such a wa y so as not to ...
-
CDA HCG 931 - page 17
17 Regulating the Burner Minimum Set ting When changing from one type of gas to another , the minimum tap output must also be correct, considering that in this position the flame must be about 4 mm long and must remain lit even when the knob is turned sharply from the maximum t o the minimum position. The adjustment is performed with the burner li ...
-
CDA HCG 931 - page 18
18 Mains Electricity Connection Incorr ect installation ma y be danger ous and the manufacturer can no t be held responsible. W arning! This appliance must be earthed The manufacturer declines all responsibility f or any problem caused b y failur e to observ e this rule. THIS APPLIANCE MUST BE C ONNECTED T O THE MAINS SUPPL Y B Y A CO MPETENT PERSO ...
-
CDA HCG 931 - page 19
19 Appliance Servicing CDA pr ovide a quality and effective after -sales service to cover all y our servicing needs. Please attac h your r eceipt to this page f or safekeeping. Please help us to help you by ha ving the following inf ormation available when booking a servic e-call: 1 . Model type, make and model – see the product data plat e. 2. E ...
-
CDA HCG 931 - page 20
Customer Car e Department • The G r oup Ltd. • Harby Road • Langar • Nottinghamshi r e • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www .cda.eu T o contact our Customer Car e Department, or for Service, please contact us on the det ails below . Cod. 1 1 03520/GB - ß4 ...
У вас вопрос, касающийся CDA HCG 931?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с CDA HCG 931, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с CDA HCG 931 со всей вероятностью он захочет поделиться методом ее решения.