Español dropdown-ico

Manual de instrucciones Harbor Freight Tools 90178

19 de páginas 3.04 mb
Descargar

Pasar a la página of 19

Summary
  • Harbor Freight Tools 90178 - page 1

    CEMENT MIXER - 3.5 CUBIC FOOT WITH BRIGGS & STRA TT ON 3.5 HP ENGINE Model 90178 ASSEMBL Y AND OPERA TING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 9301 1 Visit our W eb site at http://www .harborfreight.com Copyright 2003 by Harbor Freight T ools ® . All rights reserved. No portion of this manual or any artwork contained herein may ...

  • Harbor Freight Tools 90178 - page 2

    PRODUCT SPECIFICA TIONS SA VE THIS MANUAL Y ou will need this manual for the safety warnings and precautions, assembly , operating, inspection, maintenance and cleaning procedures, parts list and assembly diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover . Keep this manual and invoice in a safe a ...

  • Harbor Freight Tools 90178 - page 3

    6. Do not overreach. Keep proper footing and balance at all times to prevent tripping, falling, back injury , etcetera. 7. Industrial applications must follow OSHA requirements. 8. Stay alert. W atch what you are doing at all times. Use common sense. Do not use this product when you are tired or distracted from the job at hand. 9. Check for damaged ...

  • Harbor Freight Tools 90178 - page 4

    3. Keep a safe clearance around the Cement Mixer . Keep all people (except the operator) a minimum of six feet from the Mixer during operation. 4. Keep all guards in place and in proper working condition. 5. Remove adjusting tools, shovels, hand trowels, etc. Make sure all adjusting tools, shovels, hand trowels, and other tools and equipment are re ...

  • Harbor Freight Tools 90178 - page 5

    Dispose of fluids and cleaning materials in accordance with all local, state, or federal codes and regulations. Store oil rags in a covered metal container . 17. Never store fuel or other flammable materials near the Cement Mixer . 18. Do not smoke, or allow sparks, flames, or other sources of ignition around the Engine (part #14) and its fuel tank ...

  • Harbor Freight Tools 90178 - page 6

    SKU 90178 P AGE 6 UNP ACKING When unpacking, check to make sure all the parts shown on the Parts List on page 18 are included. If any parts are missing or broken, please call Harbor Freight T ools at the number shown on the cover of this manual as soon as possible. ASSEMBL Y INSTRUCTIONS NOTE: For additional references to the parts listed in the fo ...

  • Harbor Freight Tools 90178 - page 7

    SKU 90178 P AGE 7 WHEEL (#5) PIN (#4) FLA T W ASHER (#3) FIGURE B W ashers (part #10), two Spring Washers (part #9), and two Nuts (part #8). (See Figure C.) HEX BOL T (#7) FLA T W ASHER (#10) SPRING W ASHER (#9) NUT (#8) HEX BOL T (#7) FLA T W ASHER (#10) SPRING W ASHER (#9) NUT (#8) LOWER DRUM (#44) SUPPORT ARM (#31) FIGURE C 4. Align the two moun ...

  • Harbor Freight Tools 90178 - page 8

    HEX HEAD BOL T (#27) FLA T W ASHER (#10) NOT SHOWN SPRING W ASHER (#9) NOT SHOWN NUT (#8) NOT SHOWN DEGREE ADJUSTING PLA TE (#37) DEGREE ADJUSTING ARM (#38) SPRING (#39) BOL T (#40) NUT (#8) PIVOT ARM OF DEGREE ADJUSTING PLA TE (#37) FIGURE D 6. Secure the Degree Adjusting Arm (part #38) to the Pivot Shaft of the Degree Adjusting Plate (part #37), ...

  • Harbor Freight Tools 90178 - page 9

    7. Align the six mounting holes of the Connector Seal (part #45) with the six mount- ing holes in the Upper Drum (part #47). Then, glue (not included) the Connector Seal to the Upper Drum. NOTE: Make sure the Connector Seal lays flat on the Upper Drum to ensure a proper seal. (See Figure E.) UPPER DRUM (#47) CONNECTOR SEAL (#45) MOUNTING HOLE FIGUR ...

  • Harbor Freight Tools 90178 - page 10

    SKU 90178 P AGE 10 Flat W ashers (part #10), four Spring W ashers (part #9), and four Nuts (part #50) to secure the two Mixing Blades to the inside Drum assembly . (See Figure G.) MIXING BLADE (#46) MOUNT WITH V-SHAPED BENDS POINTING TO LEFT . DRUM ASSEMBL Y (#44, #47) FIGURE G 1 1. Insert the Fixing Plate (part #18) onto the Shaft (part #35). (See ...

  • Harbor Freight Tools 90178 - page 11

    FIGURE I SHAFT (#35) FIXING PLA TE (#18) FIGURE J INNER COVER (#23) SHAFT (#35) SKU 90178 P AGE 1 1 14. Align the four mounting holes in the Engine Mount Plate (part #12) with the two mounting slots located in the lower portion of the Inner Cover (part #23). Position the Small Fixing Plate (part #51) against the vertical arm of the Stand (part #1). ...

  • Harbor Freight Tools 90178 - page 12

    HEX HEAD BOL T (#27) FLA T W ASHER (#19) SPRING W ASHER (#20) NUT (#21) HEX HEAD BOL T (#27) FLA T WASHER (#19) SPRING W ASHER (#20) NUT (#21) BOL T (#48) FLA T W ASHER (#19) SPRING W ASHER (#20) NUT (#50) BOL T (#48) FLA T WASHER (#19) SPRING W ASHER (#20) NUT (#50) BOL T (#48) FLA T WASHER (#19) SPRING W ASHER (#20) NUT (#50) BOL T (#48) FLA T WA ...

  • Harbor Freight Tools 90178 - page 13

    16. Unscrew the Thrust Screw (part #17) located in the Large Pulley (part #26). Align the Keyway Slot of the Large Pulley with the Key on the Shaft (part #35). Using a hammer , carefully tap the Large Pulley onto the Shaft. Retighten the Thrust Screw to secure the Large Pulley in place. (See Figure M.) FIGURE M LARGE PULLEY (#26) SHAFT (#35) 17. Lo ...

  • Harbor Freight Tools 90178 - page 14

    18. Align the four mounting holes in the base of the Engine (part #14) with the four mounting slots in the Engine Mount Plate (#12). Insert four Hex Bolts (part #7) downward through the mounting holes and mounting slots. Insert one Flat W asher (part #10) and one Spring W asher (part #9) on each of the four Bolts. Then, finger tighten only one Nut ...

  • Harbor Freight Tools 90178 - page 15

    OPERA TING INSTRUCTIONS 1. IMPORT ANT : AL W A YS make sure the crankcase of the gasoline Engine (part #14) is filled to the proper level with a premium quality , 30-weight, non-detergent engine oil prior to starting the engine. Failure to do so will result in damage to the Engine and void its warranty . Refer to the Engine manufacturer ’s instru ...

  • Harbor Freight Tools 90178 - page 16

    SKU 90178 P AGE 16                        ? ...

  • Harbor Freight Tools 90178 - page 17

    1 1. After discharging the cement mix, raise the Degree Adjusting Arm (part #38) up to its original position. (See Figure Q.) 12. Repeat Steps #5 through #1 1 if more cement mix is required. 13. When finished, make sure to thoroughly clean the inside of the Drum (parts #44, #47). (See “Inspection, Maintenance, And Cleaning” Section.) SKU 90178 ...

  • Harbor Freight Tools 90178 - page 18

    NOTE: Some parts are listed and shown for illustration purposes only , and are not available individually as replacement parts. SKU 90178 P AGE 18 P ARTS LIST * See Briggs & Stratton Engine Parts List and Assembly Diagram for available replacement parts. ® PLEASE READ THE FOLLOWING CAREFULL Y THE MANUF ACTURER AND/OR DISTRIBUTOR HAS PROVIDED T ...

  • Harbor Freight Tools 90178 - page 19

    ASSEMBL Y DIAGRAM NOTE: Some parts are listed and shown for illustration purposes only , and are not available individually as replacement parts. SKU 90178 P AGE 19 51: SMALL FIXING PLA TE NOT SHOWN. ...

Fabricante Harbor Freight Tools Categoría Window

Los documentos del dispositivo Harbor Freight Tools 90178 que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Harbor Freight Tools
- manuales de instrucciones 90178
- hojas de producto Harbor Freight Tools
- folletos informativos
- o etiquetas energéticas Harbor Freight Tools 90178
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Harbor Freight Tools 90178.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Harbor Freight Tools 90178, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Harbor Freight Tools 90178. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Harbor Freight Tools 90178.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Harbor Freight Tools 90178, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Harbor Freight Tools 90178. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Harbor Freight Tools 90178.

El manual de instrucciones completo de Harbor Freight Tools debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Harbor Freight Tools 90178 - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Harbor Freight Tools 90178, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Harbor Freight Tools 90178 que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Harbor Freight Tools 90178 - que deben facilitarnos los primeros pasos durante el uso de Harbor Freight Tools 90178
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Harbor Freight Tools 90178
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Harbor Freight Tools 90178 en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Harbor Freight Tools 90178?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Harbor Freight Tools 90178, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Harbor Freight Tools 90178 probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Captcha
Nueva imagen

Comentarios (0)