-
Cisco Systems Cisco 1711 - page 1
CH A P T E R 2-1 Cisco 1711 and Cisco 1712 Security Access Routers Hardware Installation Guide OL-4050-02 2 Installation This chapter pro vides procedures for in stalling the Cisco 1711 and Cisco 1712 Security Access routers and incl udes the follo wing sections: • Before Installing the Router • Connecting the Router to Y our Local Network • ...
-
Cisco Systems Cisco 1711 - page 2
Chapter 2 Installation Connecting the Ro uter to Your Local Network 2-2 Cisco 1711 and Cisco 1712 Security Access R outers Hardware Installation Guide OL-4050-02 War ni n g Read the installation instruc tions before you connect the sy stem to its power source. War ni n g Do not work on the sy stem or connect or disconnect cables during periods of l ...
-
Cisco Systems Cisco 1711 - page 3
2-3 Cisco 1711 and Cisco 1712 Security Access Routers Hardware Installation Guide OL-4050-02 Chapter 2 Installation Connecting the Router to Your Lo cal Network The Cisco 1711 Security Access router is a fixed configuration router that includes a 1-port analog modem card (W IC-1-AM) that is installed in the W AN interface card (WIC) slot 1. The Cis ...
-
Cisco Systems Cisco 1711 - page 4
Chapter 2 Installation Connecting the Ro uter to Your Local Network 2-4 Cisco 1711 and Cisco 1712 Security Access R outers Hardware Installation Guide OL-4050-02 Figur e 2-1 Connecting the Router to the Local Networ k Step 2 Connect the other end of the cabl e to a network port on the hub o r switch. 91650 S E E M A N U A L B E F O R E IN S T A L L ...
-
Cisco Systems Cisco 1711 - page 5
2-5 Cisco 1711 and Cisco 1712 Security Access Routers Hardware Installation Guide OL-4050-02 Chapter 2 Installation Connecting the Router to Your Service Provider’s Equipme nt Connecting the Router to Your Service Provider’s Equipment Y ou can also connect the Cisco 1711 or Cisco 1712 S ecurity Access router to your service provider’ s broadb ...
-
Cisco Systems Cisco 1711 - page 6
Chapter 2 Installation Connecting Networke d Devices to the Router’s Sw itch Ports 2-6 Cisco 1711 and Cisco 1712 Security Access R outers Hardware Installation Guide OL-4050-02 Step 2 Connect the other end of the cabl e to a network port on your service provider’ s broadband (xDSL or cable) modem equipment . Connecting Networked Devices to the ...
-
Cisco Systems Cisco 1711 - page 7
2-7 Cisco 1711 and Cisco 1712 Security Access Routers Hardware Installation Guide OL-4050-02 Chapter 2 Installation Connecting Power to the Router Step 2 Connect the other end of the cabl e to a po rt on the hub, switch , or the Ethernet port on your com puter . Note The example provided in Figure 2-3 on page 2-6 shows connecti vity to a hub. The r ...
-
Cisco Systems Cisco 1711 - page 8
Chapter 2 Installation Connecting Power to the Router 2-8 Cisco 1711 and Cisco 1712 Security Access R outers Hardware Installation Guide OL-4050-02 War ni n g This product relies on the building’ s installation for short-circuit (overcurrent) protection. Ensure that a fuse or circuit breaker no larger than 120VAC, 15AU.S. (240V AC, 16A internatio ...
-
Cisco Systems Cisco 1711 - page 9
2-9 Cisco 1711 and Cisco 1712 Security Access Routers Hardware Installation Guide OL-4050-02 Chapter 2 Installation Connecting Power to the Router Figure 2-4 Connecting th e P ower Supply Step 2 Connect one end of the separ ate power cord t o the socket on the po wer supply . Step 3 Connect the other end of the sep arate power co rd to a power outl ...
-
Cisco Systems Cisco 1711 - page 10
Chapter 2 Installation Verifying Your Installation 2-10 Cisco 1711 and Cisco 1712 Security Access R outers Hardware Installation Guide OL-4050-02 Verifying Your Installation Y ou can verify that you h ave corr ectly installed the router by checking the follo wing LEDs: • PWR (front panel)—On when po wer is being suppli ed to the router . • OK ...
-
Cisco Systems Cisco 1711 - page 11
2-11 Cisco 1711 and Cisco 1712 Security Access Routers Hardware Installation Guide OL-4050-02 Chapter 2 Installation Optional Installation Ste ps Connecting a PC to the Router’s Console Port If you want t o configure the router by using the Cisco IOS command-line interface, you must connect the router cons ole port to a terminal or PC. The cable ...
-
Cisco Systems Cisco 1711 - page 12
Chapter 2 Installation Optional Installation Steps 2-12 Cisco 1711 and Cisco 1712 Security Access R outers Hardware Installation Guide OL-4050-02 Figure 2-5 Connecting the Consol e Cable to the Router Step 2 Connect the DB-9 end of the console cabl e to the console port (also called the serial port ) on your PC. If this adapt er does not fit your P ...
-
Cisco Systems Cisco 1711 - page 13
2-13 Cisco 1711 and Cisco 1712 Security Access Routers Hardware Installation Guide OL-4050-02 Chapter 2 Installation Optional Installation Ste ps Note An external modem is not req uired for use on the Cisco 1711 Securit y Access router WIC-1-AM card. Follo w these steps to conn ect a modem to the router , using the console cabl e: Step 1 Connect th ...
-
Cisco Systems Cisco 1711 - page 14
Chapter 2 Installation Optional Installation Steps 2-14 Cisco 1711 and Cisco 1712 Security Access R outers Hardware Installation Guide OL-4050-02 Step 2 Connect the DB-9 end of the cable to th e DB-9 end of the DB-9-to-DB-25 adapter . Step 3 Connect the DB-25 end of the ad apter to the modem. Wall-Mounting The Cisco 1711 and Cisco 1712 Security Acc ...
-
Cisco Systems Cisco 1711 - page 15
2-15 Cisco 1711 and Cisco 1712 Security Access Routers Hardware Installation Guide OL-4050-02 Chapter 2 Installation Optional Installation Ste ps Step 2 Hang the router on the screws with either t he left side or right side mounting brackets so that • The LEDs are visible to the user—B ecause the LEDs indicate the router operating status, they ...
-
Cisco Systems Cisco 1711 - page 16
Chapter 2 Installation Optional Installation Steps 2-16 Cisco 1711 and Cisco 1712 Security Access R outers Hardware Installation Guide OL-4050-02 Figur e 2-8 Assembling Stacking Clip and F astener After assembling the clip and fastener , foll o w these steps to stack the router with another de vice: Step 1 Place the clip on top of the lo wer device ...
-
Cisco Systems Cisco 1711 - page 17
2-17 Cisco 1711 and Cisco 1712 Security Access Routers Hardware Installation Guide OL-4050-02 Chapter 2 Installation Optional Installation Ste ps Figure 2-9 Stacking the Router Step 2 Position the router on to the clips so that the rear hooks fit o ver the edge of the router . Step 3 Snap the rou ter to the clip by push ing it do wn. Make sure that ...
-
Cisco Systems Cisco 1711 - page 18
Chapter 2 Installation Optional Installation Steps 2-18 Cisco 1711 and Cisco 1712 Security Access R outers Hardware Installation Guide OL-4050-02 Unstacking the Router Follo w these steps to unst ack the router from another device: Step 1 Press up on the tab ov er the center of the lower de vice to release the clip from the ven t, as s how n i n Fi ...
-
Cisco Systems Cisco 1711 - page 19
2-19 Cisco 1711 and Cisco 1712 Security Access Routers Hardware Installation Guide OL-4050-02 Chapter 2 Installation Optional Installation Ste ps Step 2 Slide the clip and router tow ard you. Step 3 Use both han ds to lift th e router and the stacking clip of f the lower de vice. Afterward, remo ve the clip fr om the bottom of the router . ...
-
Cisco Systems Cisco 1711 - page 20
Chapter 2 Installation Optional Installation Steps 2-20 Cisco 1711 and Cisco 1712 Security Access R outers Hardware Installation Guide OL-4050-02 ...
¿Tienes una pregunta acerca de Cisco Systems Cisco 1711?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Cisco Systems Cisco 1711, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Cisco Systems Cisco 1711 probablemente compartirá una forma de solucionarlo.