Manuel d’utilisation Cisco Systems Cisco 1711

20 pages 0.54 mb
Télécharger

Aller à la page of 20

Summary
  • Cisco Systems Cisco 1711 - page 1

    CH A P T E R 2-1 Cisco 1711 and Cisco 1712 Security Access Routers Hardware Installation Guide OL-4050-02 2 Installation This chapter pro vides procedures for in stalling the Cisco 1711 and Cisco 1712 Security Access routers and incl udes the follo wing sections: • Before Installing the Router • Connecting the Router to Y our Local Network • ...

  • Cisco Systems Cisco 1711 - page 2

    Chapter 2 Installation Connecting the Ro uter to Your Local Network 2-2 Cisco 1711 and Cisco 1712 Security Access R outers Hardware Installation Guide OL-4050-02 War ni n g Read the installation instruc tions before you connect the sy stem to its power source. War ni n g Do not work on the sy stem or connect or disconnect cables during periods of l ...

  • Cisco Systems Cisco 1711 - page 3

    2-3 Cisco 1711 and Cisco 1712 Security Access Routers Hardware Installation Guide OL-4050-02 Chapter 2 Installation Connecting the Router to Your Lo cal Network The Cisco 1711 Security Access router is a fixed configuration router that includes a 1-port analog modem card (W IC-1-AM) that is installed in the W AN interface card (WIC) slot 1. The Cis ...

  • Cisco Systems Cisco 1711 - page 4

    Chapter 2 Installation Connecting the Ro uter to Your Local Network 2-4 Cisco 1711 and Cisco 1712 Security Access R outers Hardware Installation Guide OL-4050-02 Figur e 2-1 Connecting the Router to the Local Networ k Step 2 Connect the other end of the cabl e to a network port on the hub o r switch. 91650 S E E M A N U A L B E F O R E IN S T A L L ...

  • Cisco Systems Cisco 1711 - page 5

    2-5 Cisco 1711 and Cisco 1712 Security Access Routers Hardware Installation Guide OL-4050-02 Chapter 2 Installation Connecting the Router to Your Service Provider’s Equipme nt Connecting the Router to Your Service Provider’s Equipment Y ou can also connect the Cisco 1711 or Cisco 1712 S ecurity Access router to your service provider’ s broadb ...

  • Cisco Systems Cisco 1711 - page 6

    Chapter 2 Installation Connecting Networke d Devices to the Router’s Sw itch Ports 2-6 Cisco 1711 and Cisco 1712 Security Access R outers Hardware Installation Guide OL-4050-02 Step 2 Connect the other end of the cabl e to a network port on your service provider’ s broadband (xDSL or cable) modem equipment . Connecting Networked Devices to the ...

  • Cisco Systems Cisco 1711 - page 7

    2-7 Cisco 1711 and Cisco 1712 Security Access Routers Hardware Installation Guide OL-4050-02 Chapter 2 Installation Connecting Power to the Router Step 2 Connect the other end of the cabl e to a po rt on the hub, switch , or the Ethernet port on your com puter . Note The example provided in Figure 2-3 on page 2-6 shows connecti vity to a hub. The r ...

  • Cisco Systems Cisco 1711 - page 8

    Chapter 2 Installation Connecting Power to the Router 2-8 Cisco 1711 and Cisco 1712 Security Access R outers Hardware Installation Guide OL-4050-02 War ni n g This product relies on the building’ s installation for short-circuit (overcurrent) protection. Ensure that a fuse or circuit breaker no larger than 120VAC, 15AU.S. (240V AC, 16A internatio ...

  • Cisco Systems Cisco 1711 - page 9

    2-9 Cisco 1711 and Cisco 1712 Security Access Routers Hardware Installation Guide OL-4050-02 Chapter 2 Installation Connecting Power to the Router Figure 2-4 Connecting th e P ower Supply Step 2 Connect one end of the separ ate power cord t o the socket on the po wer supply . Step 3 Connect the other end of the sep arate power co rd to a power outl ...

  • Cisco Systems Cisco 1711 - page 10

    Chapter 2 Installation Verifying Your Installation 2-10 Cisco 1711 and Cisco 1712 Security Access R outers Hardware Installation Guide OL-4050-02 Verifying Your Installation Y ou can verify that you h ave corr ectly installed the router by checking the follo wing LEDs: • PWR (front panel)—On when po wer is being suppli ed to the router . • OK ...

  • Cisco Systems Cisco 1711 - page 11

    2-11 Cisco 1711 and Cisco 1712 Security Access Routers Hardware Installation Guide OL-4050-02 Chapter 2 Installation Optional Installation Ste ps Connecting a PC to the Router’s Console Port If you want t o configure the router by using the Cisco IOS command-line interface, you must connect the router cons ole port to a terminal or PC. The cable ...

  • Cisco Systems Cisco 1711 - page 12

    Chapter 2 Installation Optional Installation Steps 2-12 Cisco 1711 and Cisco 1712 Security Access R outers Hardware Installation Guide OL-4050-02 Figure 2-5 Connecting the Consol e Cable to the Router Step 2 Connect the DB-9 end of the console cabl e to the console port (also called the serial port ) on your PC. If this adapt er does not fit your P ...

  • Cisco Systems Cisco 1711 - page 13

    2-13 Cisco 1711 and Cisco 1712 Security Access Routers Hardware Installation Guide OL-4050-02 Chapter 2 Installation Optional Installation Ste ps Note An external modem is not req uired for use on the Cisco 1711 Securit y Access router WIC-1-AM card. Follo w these steps to conn ect a modem to the router , using the console cabl e: Step 1 Connect th ...

  • Cisco Systems Cisco 1711 - page 14

    Chapter 2 Installation Optional Installation Steps 2-14 Cisco 1711 and Cisco 1712 Security Access R outers Hardware Installation Guide OL-4050-02 Step 2 Connect the DB-9 end of the cable to th e DB-9 end of the DB-9-to-DB-25 adapter . Step 3 Connect the DB-25 end of the ad apter to the modem. Wall-Mounting The Cisco 1711 and Cisco 1712 Security Acc ...

  • Cisco Systems Cisco 1711 - page 15

    2-15 Cisco 1711 and Cisco 1712 Security Access Routers Hardware Installation Guide OL-4050-02 Chapter 2 Installation Optional Installation Ste ps Step 2 Hang the router on the screws with either t he left side or right side mounting brackets so that • The LEDs are visible to the user—B ecause the LEDs indicate the router operating status, they ...

  • Cisco Systems Cisco 1711 - page 16

    Chapter 2 Installation Optional Installation Steps 2-16 Cisco 1711 and Cisco 1712 Security Access R outers Hardware Installation Guide OL-4050-02 Figur e 2-8 Assembling Stacking Clip and F astener After assembling the clip and fastener , foll o w these steps to stack the router with another de vice: Step 1 Place the clip on top of the lo wer device ...

  • Cisco Systems Cisco 1711 - page 17

    2-17 Cisco 1711 and Cisco 1712 Security Access Routers Hardware Installation Guide OL-4050-02 Chapter 2 Installation Optional Installation Ste ps Figure 2-9 Stacking the Router Step 2 Position the router on to the clips so that the rear hooks fit o ver the edge of the router . Step 3 Snap the rou ter to the clip by push ing it do wn. Make sure that ...

  • Cisco Systems Cisco 1711 - page 18

    Chapter 2 Installation Optional Installation Steps 2-18 Cisco 1711 and Cisco 1712 Security Access R outers Hardware Installation Guide OL-4050-02 Unstacking the Router Follo w these steps to unst ack the router from another device: Step 1 Press up on the tab ov er the center of the lower de vice to release the clip from the ven t, as s how n i n Fi ...

  • Cisco Systems Cisco 1711 - page 19

    2-19 Cisco 1711 and Cisco 1712 Security Access Routers Hardware Installation Guide OL-4050-02 Chapter 2 Installation Optional Installation Ste ps Step 2 Slide the clip and router tow ard you. Step 3 Use both han ds to lift th e router and the stacking clip of f the lower de vice. Afterward, remo ve the clip fr om the bottom of the router . ...

  • Cisco Systems Cisco 1711 - page 20

    Chapter 2 Installation Optional Installation Steps 2-20 Cisco 1711 and Cisco 1712 Security Access R outers Hardware Installation Guide OL-4050-02 ...

Fabricant Cisco Systems Catégorie Router

Les documents que nous recevons du fabricant de l'appareilCisco Systems Cisco 1711 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Cisco Systems
- manuels d’utilisations Cisco 1711
- fiches produit Cisco Systems
- dépliants
- ou étiquettes-énergie Cisco Systems Cisco 1711
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Cisco Systems Cisco 1711.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Cisco Systems Cisco 1711, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Cisco Systems Cisco 1711. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Cisco Systems Cisco 1711.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Cisco Systems Cisco 1711, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Cisco Systems Cisco 1711 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Cisco Systems Cisco 1711.

Le manuel d’utilisation complet Cisco Systems, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Cisco Systems Cisco 1711 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Cisco Systems Cisco 1711, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lCisco Systems Cisco 1711 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Cisco Systems Cisco 1711 - qui devraient nous aider dans les premières étapes lors de l'utilisation Cisco Systems Cisco 1711
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Cisco Systems Cisco 1711
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Cisco Systems Cisco 1711 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Cisco Systems Cisco 1711?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Cisco Systems Cisco 1711, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Cisco Systems Cisco 1711 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Commentaires (0)