Español dropdown-ico

Manual de instrucciones Bloomfield 2030

26 de páginas 1.13 mb
Descargar

Pasar a la página of 26

Summary
  • Bloomfield 2030 - page 1

    PRINTED IN UNITED STATES OF A MERIC A p/n 73902 Rev. F ECN- 12817 M653 05 0208 cps 653 OWNERS MANUAL for E-Max™ TEA BREWERS MOD EL S 2030 Includes: Installation Operation Use & Care Servicing Instructions Mode l 2030 Tea Brewer with optional 8799 Dispenser E-Max BREWERS are cov ered under U. S. Patents #5704275, 5862738, 6095031. Other U.S. P ...

  • Bloomfield 2030 - page 2

    NOTE: For your protection, please note that equipment in this shipment was carefully inspected and packaged b y skilled personnel before le aving the factory. Upon acceptance of this shipm ent, the transportation company assumes full responsibility for its safe delivery. IF SHIPMENT ARRIVES DAMAGED: 1. VISIBLE LOSS OR DAMAGE: Be certain that any v ...

  • Bloomfield 2030 - page 3

    TABLE OF CONTENTS SPECIFICATIONS Thank You for purc hasing this Bloomfield Industries appliance. Proper installation, professional operation and consistent maintenance of this appliance w ill ensure that it gives you the very best performance and a long, economical service life. This ma nual contains t he information needed to properly install this ...

  • Bloomfield 2030 - page 4

    FE AT U R E S AN D O P E R AT I N G CO N T R OL S 2 Features & Operating Contro ls ...

  • Bloomfield 2030 - page 5

    WARNING: Electric Shock Hazard All servicing requiring access to non-insu lated components must be performed by qualified service personnel. Do not open any access panels wh ich require the use of tools. Failure to heed this warning can re su lt in electrical shock. WA RNI NG : Injury Hazard All installation procedures must be performed by qualifie ...

  • Bloomfield 2030 - page 6

    INSTALLATION INSTRUCTIONS RE A D THIS CAREFULL Y BEFORE ST A RTING THE INST AL L A TION UNPACKING & INITIAL INSPECTION 1. Unpack the unit. Inspec t all components for c ompleteness and condition. Ensure that all pack ing materials have been rem oved from the unit. 2. Verify that the Spray Head and Spray Head Gasket ar e pr operly installed. ( S ...

  • Bloomfield 2030 - page 7

    INSTALLATION INSTRUCTIONS (continued) NOTE: This equipment must be installed to comply with applicable federal, state an d local plum bing codes an d ordinanc es. WARNING ELECTRIC SHOCK HAZARD: Brewer must be properly grounded to prevent possible shock hazard. DO NOT assume a plumbing line will provide suc h a ground . Electrical shock will cause d ...

  • Bloomfield 2030 - page 8

    OPERATION IMPORTANT: All E-Max T™ brewers are tested and set a t the facto ry . If programming adjust- ments are necessary, refer to the E -Ma x™ Programming Manual (p/n 73674). To over-ride th e Br ew Wait mode , press and hold the BR EW key for 3 second s when the brewer is in Bre w Wait mode (i.e. when brew light is flashing). The brew will ...

  • Bloomfield 2030 - page 9

    OPERATION (continued) WA R N IN G: Burn Hazard. This appliance dispenses very hot liquid. Serious bodily injury from scalding can occur from contact with dispensed liquids. C AUTION: B urn Hazard To avoid splashing or overflowing ho t liquids, ALWAYS use an empty dispenser before starting the brew cycle. Failure to comply can cause serious burns. C ...

  • Bloomfield 2030 - page 10

    PROGRAMMING FEATURES AND OPTIONS 1. View Water Temperature in Ta nk: To view the water tem perature on the screen, E-Max T™ bre we r must be ON, and not brewing or in the filling mode. Press and hold the 4th key, and depress the 6th k ey . The actual water temperature w ill be displayed for 3 seconds. 2. Daily Br ew Count: The E-Max T ™ maintai ...

  • Bloomfield 2030 - page 11

    8. Cl ock A. Time – Battery Backup. The E-Max T™ has a battery back up sy stem which will maintain the proper time during power failures, or when the brewer is unplugge d (e ven for very prolonged periods of time). Normal ly there will not be a need to set the time except for Daylight Saving Time changes, or moving the brewer to different time ...

  • Bloomfield 2030 - page 12

    OPERATION (continued) 10 12. View Fil ter Statistics: To view filter statistics, turn the br e wer off. P ress and hold the 1s t ke y (Brew), and depress the 3rd (ON/OFF) k ey. Total water volume will be displa yed (TotalVol.). Press the 3rd k ey to view the Filter Lif e (F ltrLife :). Press the 3r d key to view the percen tage of the filter that h ...

  • Bloomfield 2030 - page 13

    CLEANING I NSTRUCTIONS PROCEDURE: Clean Coffee Br e wer PRECAUTIONS: Disconnect brew er from electric power. Allow brewer to cool. FREQUENCY: Dail y TOOLS: Mi ld Detergent, Clean Sof t Cloth or Sponge Bristle Brush 1. Disconnect brewer from electric power. Allow brewer to cool before cleaning. 2. Remove dispenser. 3. Remove and empty brew chamber. ...

  • Bloomfield 2030 - page 14

    FUNCTION 1. W ater enters at the inlet fitt ing of the fill solenoid (32). The s olenoid admits water via a command from the controller. N OTE: The solenoid has an inter nal strainer. To clean the s trainer: Shu t off water s upply. Unscre w the plast ic cap protruding f rom the rear of the brewer. Remove the cap, inlet f itting and washer. W ith p ...

  • Bloomfield 2030 - page 15

    SERVICING IN STRUCTIONS — PLUM BING (continued) 13 ITEM DESCRIPTI ON P ART N0. USED ON 1 2 ASS E MBL Y , WA TER T ANK (120 V) 835 0 0 2030 6 GAS KET , T ANK LID 83499 2 030 9 TANK LI D 835 04 2 03 0 10 RET A INING CLIP , T ANK LID 83506 2 030 1 1 HO S E, V ENT (SIL I C O N E 4. 5” LONG ) 860 1 4 2030 12 HOSE , F AUCE T SU PPL Y (SILICO NE, 1 0? ...

  • Bloomfield 2030 - page 16

    SERVICING INSTRUCTIO NS - ELECTRICAL FUNCTION 1. Pressing th e POWER k ey energizes the unit. The POWER LED will glow whenever the unit is ON . 2. Automatic fill is accomplished via the "FILL" section of the INLET SOLENOID (32) and a WATER LEVEL PROBE (7). The probe senses groun d through the water in the tank. W hen the w ater level fall ...

  • Bloomfield 2030 - page 17

    SERVICING INSTRUCTIONS - ELECTRICAL (continued) 15 ITEM DESCR IP TI ON P ART N0 . USED ON 3 PROBE, TEMPERA TURE 834 80 ALL 4 T HER M O ST A T , H I-L I M IT S A FE TY (1 20 V ) 8394 9 ALL 5 GROMME T , TEMP PROBE 84063 ALL 7 SE NSOR, WA TE R L EVEL 835 21 AL L 8 SLEEV E, WA TE R L EVEL SENSOR 835 32 ALL 15 ELE M E N T , HE A TER 15 00W (12 0V) 8351 ...

  • Bloomfield 2030 - page 18

    SERVICING INSTRUCTIONS — DE-LIMING HE A TER TANK 1. Disconn e ct brewer form the electrical suppl y. Turn off the water suppl y and disconne ct water suppl y from the brewer inlet fitting. 2. R emove the top panel to gain acc ess to internal components. 3. Disconnect water level sensor and water temperature sensor from the controlle r. On 120V un ...

  • Bloomfield 2030 - page 19

    TROUBLESHOOTING SUGGESTIONS If the E-Max T™ goes into the error m o d e as ou tlined belo w, it will likely be necessar y to reset the brewer in order to test individual com ponents. Note the reset procedure belo w: • For the first four error modes, press and hold CANCEL for 3 seconds, or RE-ENERGIZE the brewer by disconnecting from electric po ...

  • Bloomfield 2030 - page 20

    E-Max T™ TEST PROGRAM 18 Instructions for testing procedures fo r the follow in g system components (using the E-Max T™ Built-In Diagnostic): Electronic Board Softwa re (Firmwa re) Re vision Keypad switches LED’s Inlet valve, Dump (Brew) valve, By Pass Valve Water level probe, Temperature probe A. Entering Test Progra m Mode: 1. Make sure to ...

  • Bloomfield 2030 - page 21

    E-Max T™ TEST PROGRAM (continued) 19 E. LED Test The display should read “Testing LED’s”: Individual LED’s will be tested i ndividually, beginning with the first on the left, and proceeding thro ugh all six LED’s at one-second intervals. Screen will read “Testing LED’s” during the entire test. 1. Verif y that only one LED at a tim ...

  • Bloomfield 2030 - page 22

    EXPLODED VIEW & PARTS LIST 20 ...

  • Bloomfield 2030 - page 23

    EXPLODED VIEW & PART S LIST (continued) 21 ITEM P ART # DESCRIPTI ON QTY 1 8783-1 F A UCET , HOT W A TER 1 2 83500 T A NK ASSEM BL Y , 120V 1 3 83480 THERMISTOR , 5-½" 1 4 83949 THERMO, HI -LI MIT CERA MIC, 12 0V 1 5 821 15 GROMMET , ¼ ID TRANSLUCENT 1 6 83499 GASKET , T ANK COVER 1 7 83521 W A TER LEV EL ASSY 1 8 83532 PROBE, SLEEVE, WA ...

  • Bloomfield 2030 - page 24

    WIRING DIAGRAMS (continued) 22 ...

  • Bloomfield 2030 - page 25

    NOTES 23 ...

  • Bloomfield 2030 - page 26

    PRINTED IN UNITED STATES OF AMERICA Bloo mf iel d Indu stri es, Inc . Division of Carrier Co mmercial Refrigeration In US and Can ada T elep hone: 775 -689- 5700 Fa x: 888-4 92-2783 Fa x: 800-3 56-5142 () websi te: www . wells bl oomfi eld. com fo r order s onl y Bloomf iel d Indus t ri es p roudl y suppor ts CFESA Commerc ial Fo od Equi pment Serv ...

Fabricante Bloomfield Categoría Coffeemaker

Los documentos del dispositivo Bloomfield 2030 que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Bloomfield
- manuales de instrucciones 2030
- hojas de producto Bloomfield
- folletos informativos
- o etiquetas energéticas Bloomfield 2030
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Bloomfield 2030.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Bloomfield 2030, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Bloomfield 2030. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Bloomfield 2030.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Bloomfield 2030, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Bloomfield 2030. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Bloomfield 2030.

El manual de instrucciones completo de Bloomfield debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Bloomfield 2030 - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Bloomfield 2030, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Bloomfield 2030 que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Bloomfield 2030 - que deben facilitarnos los primeros pasos durante el uso de Bloomfield 2030
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Bloomfield 2030
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Bloomfield 2030 en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Bloomfield 2030?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Bloomfield 2030, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Bloomfield 2030 probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Captcha
Nueva imagen

Comentarios (0)