English dropdown-ico

Manual Bloomfield 2030

26 pages 1.13 mb
Download

Go to site of 26

Summary
  • Bloomfield 2030 - page 1

    PRINTED IN UNITED STATES OF A MERIC A p/n 73902 Rev. F ECN- 12817 M653 05 0208 cps 653 OWNERS MANUAL for E-Max™ TEA BREWERS MOD EL S 2030 Includes: Installation Operation Use & Care Servicing Instructions Mode l 2030 Tea Brewer with optional 8799 Dispenser E-Max BREWERS are cov ered under U. S. Patents #5704275, 5862738, 6095031. Other U.S. P ...

  • Bloomfield 2030 - page 2

    NOTE: For your protection, please note that equipment in this shipment was carefully inspected and packaged b y skilled personnel before le aving the factory. Upon acceptance of this shipm ent, the transportation company assumes full responsibility for its safe delivery. IF SHIPMENT ARRIVES DAMAGED: 1. VISIBLE LOSS OR DAMAGE: Be certain that any v ...

  • Bloomfield 2030 - page 3

    TABLE OF CONTENTS SPECIFICATIONS Thank You for purc hasing this Bloomfield Industries appliance. Proper installation, professional operation and consistent maintenance of this appliance w ill ensure that it gives you the very best performance and a long, economical service life. This ma nual contains t he information needed to properly install this ...

  • Bloomfield 2030 - page 4

    FE AT U R E S AN D O P E R AT I N G CO N T R OL S 2 Features & Operating Contro ls ...

  • Bloomfield 2030 - page 5

    WARNING: Electric Shock Hazard All servicing requiring access to non-insu lated components must be performed by qualified service personnel. Do not open any access panels wh ich require the use of tools. Failure to heed this warning can re su lt in electrical shock. WA RNI NG : Injury Hazard All installation procedures must be performed by qualifie ...

  • Bloomfield 2030 - page 6

    INSTALLATION INSTRUCTIONS RE A D THIS CAREFULL Y BEFORE ST A RTING THE INST AL L A TION UNPACKING & INITIAL INSPECTION 1. Unpack the unit. Inspec t all components for c ompleteness and condition. Ensure that all pack ing materials have been rem oved from the unit. 2. Verify that the Spray Head and Spray Head Gasket ar e pr operly installed. ( S ...

  • Bloomfield 2030 - page 7

    INSTALLATION INSTRUCTIONS (continued) NOTE: This equipment must be installed to comply with applicable federal, state an d local plum bing codes an d ordinanc es. WARNING ELECTRIC SHOCK HAZARD: Brewer must be properly grounded to prevent possible shock hazard. DO NOT assume a plumbing line will provide suc h a ground . Electrical shock will cause d ...

  • Bloomfield 2030 - page 8

    OPERATION IMPORTANT: All E-Max T™ brewers are tested and set a t the facto ry . If programming adjust- ments are necessary, refer to the E -Ma x™ Programming Manual (p/n 73674). To over-ride th e Br ew Wait mode , press and hold the BR EW key for 3 second s when the brewer is in Bre w Wait mode (i.e. when brew light is flashing). The brew will ...

  • Bloomfield 2030 - page 9

    OPERATION (continued) WA R N IN G: Burn Hazard. This appliance dispenses very hot liquid. Serious bodily injury from scalding can occur from contact with dispensed liquids. C AUTION: B urn Hazard To avoid splashing or overflowing ho t liquids, ALWAYS use an empty dispenser before starting the brew cycle. Failure to comply can cause serious burns. C ...

  • Bloomfield 2030 - page 10

    PROGRAMMING FEATURES AND OPTIONS 1. View Water Temperature in Ta nk: To view the water tem perature on the screen, E-Max T™ bre we r must be ON, and not brewing or in the filling mode. Press and hold the 4th key, and depress the 6th k ey . The actual water temperature w ill be displayed for 3 seconds. 2. Daily Br ew Count: The E-Max T ™ maintai ...

  • Bloomfield 2030 - page 11

    8. Cl ock A. Time – Battery Backup. The E-Max T™ has a battery back up sy stem which will maintain the proper time during power failures, or when the brewer is unplugge d (e ven for very prolonged periods of time). Normal ly there will not be a need to set the time except for Daylight Saving Time changes, or moving the brewer to different time ...

  • Bloomfield 2030 - page 12

    OPERATION (continued) 10 12. View Fil ter Statistics: To view filter statistics, turn the br e wer off. P ress and hold the 1s t ke y (Brew), and depress the 3rd (ON/OFF) k ey. Total water volume will be displa yed (TotalVol.). Press the 3rd k ey to view the Filter Lif e (F ltrLife :). Press the 3r d key to view the percen tage of the filter that h ...

  • Bloomfield 2030 - page 13

    CLEANING I NSTRUCTIONS PROCEDURE: Clean Coffee Br e wer PRECAUTIONS: Disconnect brew er from electric power. Allow brewer to cool. FREQUENCY: Dail y TOOLS: Mi ld Detergent, Clean Sof t Cloth or Sponge Bristle Brush 1. Disconnect brewer from electric power. Allow brewer to cool before cleaning. 2. Remove dispenser. 3. Remove and empty brew chamber. ...

  • Bloomfield 2030 - page 14

    FUNCTION 1. W ater enters at the inlet fitt ing of the fill solenoid (32). The s olenoid admits water via a command from the controller. N OTE: The solenoid has an inter nal strainer. To clean the s trainer: Shu t off water s upply. Unscre w the plast ic cap protruding f rom the rear of the brewer. Remove the cap, inlet f itting and washer. W ith p ...

  • Bloomfield 2030 - page 15

    SERVICING IN STRUCTIONS — PLUM BING (continued) 13 ITEM DESCRIPTI ON P ART N0. USED ON 1 2 ASS E MBL Y , WA TER T ANK (120 V) 835 0 0 2030 6 GAS KET , T ANK LID 83499 2 030 9 TANK LI D 835 04 2 03 0 10 RET A INING CLIP , T ANK LID 83506 2 030 1 1 HO S E, V ENT (SIL I C O N E 4. 5” LONG ) 860 1 4 2030 12 HOSE , F AUCE T SU PPL Y (SILICO NE, 1 0? ...

  • Bloomfield 2030 - page 16

    SERVICING INSTRUCTIO NS - ELECTRICAL FUNCTION 1. Pressing th e POWER k ey energizes the unit. The POWER LED will glow whenever the unit is ON . 2. Automatic fill is accomplished via the "FILL" section of the INLET SOLENOID (32) and a WATER LEVEL PROBE (7). The probe senses groun d through the water in the tank. W hen the w ater level fall ...

  • Bloomfield 2030 - page 17

    SERVICING INSTRUCTIONS - ELECTRICAL (continued) 15 ITEM DESCR IP TI ON P ART N0 . USED ON 3 PROBE, TEMPERA TURE 834 80 ALL 4 T HER M O ST A T , H I-L I M IT S A FE TY (1 20 V ) 8394 9 ALL 5 GROMME T , TEMP PROBE 84063 ALL 7 SE NSOR, WA TE R L EVEL 835 21 AL L 8 SLEEV E, WA TE R L EVEL SENSOR 835 32 ALL 15 ELE M E N T , HE A TER 15 00W (12 0V) 8351 ...

  • Bloomfield 2030 - page 18

    SERVICING INSTRUCTIONS — DE-LIMING HE A TER TANK 1. Disconn e ct brewer form the electrical suppl y. Turn off the water suppl y and disconne ct water suppl y from the brewer inlet fitting. 2. R emove the top panel to gain acc ess to internal components. 3. Disconnect water level sensor and water temperature sensor from the controlle r. On 120V un ...

  • Bloomfield 2030 - page 19

    TROUBLESHOOTING SUGGESTIONS If the E-Max T™ goes into the error m o d e as ou tlined belo w, it will likely be necessar y to reset the brewer in order to test individual com ponents. Note the reset procedure belo w: • For the first four error modes, press and hold CANCEL for 3 seconds, or RE-ENERGIZE the brewer by disconnecting from electric po ...

  • Bloomfield 2030 - page 20

    E-Max T™ TEST PROGRAM 18 Instructions for testing procedures fo r the follow in g system components (using the E-Max T™ Built-In Diagnostic): Electronic Board Softwa re (Firmwa re) Re vision Keypad switches LED’s Inlet valve, Dump (Brew) valve, By Pass Valve Water level probe, Temperature probe A. Entering Test Progra m Mode: 1. Make sure to ...

  • Bloomfield 2030 - page 21

    E-Max T™ TEST PROGRAM (continued) 19 E. LED Test The display should read “Testing LED’s”: Individual LED’s will be tested i ndividually, beginning with the first on the left, and proceeding thro ugh all six LED’s at one-second intervals. Screen will read “Testing LED’s” during the entire test. 1. Verif y that only one LED at a tim ...

  • Bloomfield 2030 - page 22

    EXPLODED VIEW & PARTS LIST 20 ...

  • Bloomfield 2030 - page 23

    EXPLODED VIEW & PART S LIST (continued) 21 ITEM P ART # DESCRIPTI ON QTY 1 8783-1 F A UCET , HOT W A TER 1 2 83500 T A NK ASSEM BL Y , 120V 1 3 83480 THERMISTOR , 5-½" 1 4 83949 THERMO, HI -LI MIT CERA MIC, 12 0V 1 5 821 15 GROMMET , ¼ ID TRANSLUCENT 1 6 83499 GASKET , T ANK COVER 1 7 83521 W A TER LEV EL ASSY 1 8 83532 PROBE, SLEEVE, WA ...

  • Bloomfield 2030 - page 24

    WIRING DIAGRAMS (continued) 22 ...

  • Bloomfield 2030 - page 25

    NOTES 23 ...

  • Bloomfield 2030 - page 26

    PRINTED IN UNITED STATES OF AMERICA Bloo mf iel d Indu stri es, Inc . Division of Carrier Co mmercial Refrigeration In US and Can ada T elep hone: 775 -689- 5700 Fa x: 888-4 92-2783 Fa x: 800-3 56-5142 () websi te: www . wells bl oomfi eld. com fo r order s onl y Bloomf iel d Indus t ri es p roudl y suppor ts CFESA Commerc ial Fo od Equi pment Serv ...

Manufacturer Bloomfield Category Coffeemaker

Documents that we receive from a manufacturer of a Bloomfield 2030 can be divided into several groups. They are, among others:
- Bloomfield technical drawings
- 2030 manuals
- Bloomfield product data sheets
- information booklets
- or energy labels Bloomfield 2030
All of them are important, but the most important information from the point of view of use of the device are in the user manual Bloomfield 2030.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Bloomfield 2030, service manual, brief instructions and user manuals Bloomfield 2030. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Bloomfield 2030.

Similar manuals

A complete manual for the device Bloomfield 2030, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Bloomfield 2030 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Bloomfield 2030.

A complete Bloomfield manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Bloomfield 2030 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Bloomfield 2030, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Bloomfield 2030, that we can find in the current document
3. Tips how to use the basic functions of the device Bloomfield 2030 - which should help us in our first steps of using Bloomfield 2030
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Bloomfield 2030
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Bloomfield 2030 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Bloomfield 2030?

Use the form below

If you did not solve your problem by using a manual Bloomfield 2030, ask a question using the form below. If a user had a similar problem with Bloomfield 2030 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)