-
Atech Tech LIBRA-04 M - page 1
LIBRA-04 M MANUAL COP Y ROUTER LIBRA-04 M MANUAL COPY ROUTER User's Manual ...
-
Atech Tech LIBRA-04 M - page 2
LIBRA-04 M MANUAL COP Y ROUTER TABLE OF CONTENTS ITEM # SUBJECT PAGE # I INTRODUCTION 3 II SAFETY APPLICATION S 4 II.1 DESCRIPTION OF SY MBOLS USED IN THIS USER’S MANUAL 4 II.2 SAFETY INSTRUCTION S 5 III MACHINE DESCRIPT ION 8 III.1 TECHNICAL DESCRIPT ION 9 III.2 TECHNICAL DATA 9 IV INSTALLATION 10 IV.1 MACHINE LIFTING A ND MOVING 10 IV.2 THE REQ ...
-
Atech Tech LIBRA-04 M - page 3
LIBRA-04 M MANUAL COPY ROUTER 3 / 19 I. GENER A L INFORMATION 1.1. INTRODUCTION The user’s manual giv en by the manufactur er contains necessary inf ormation about the m achine parts. E ach m achine o perator should read these instructions car efully, and the machine shoul d be operated after f ully understa nding them. Safe and ef ficient use of ...
-
Atech Tech LIBRA-04 M - page 4
LIBRA-04 M MANUAL COPY ROUTER 4 / 19 II – SAFETY APP L ICATION Before operating this equipment, be sure of reading and understanding the safety instructions. The operator may not run the m achine without readi ng this g uide. Reading a nd underst anding t his us er guide is im portant f or hindering to injur y to t he operator, third persons, ani ...
-
Atech Tech LIBRA-04 M - page 5
LIBRA-04 M MANUAL COPY ROUTER 5 / 19 This explains not be pulled up the protective parts . Do not operate without g uards. This is high temp er ature s y mbol. II.2 – S A FETY INSTRUCTION S Before operating this equipment , read the safety instructions an d carry out them. This technical handbook sh ould be accessible at all times at the site of ...
-
Atech Tech LIBRA-04 M - page 6
LIBRA-04 M MANUAL COPY ROUTER 6 / 19 Use only original spa re part. Don’t lean against control pa nel and do not force. Use e-Stop b utton when necessar y f or stopping the m achine because ver y frequent repetition o f this process, may cause probl ems on th e some electric components. Service personnel of our c ompany is responsible f rom the f ...
-
Atech Tech LIBRA-04 M - page 7
LIBRA-04 M MANUAL COPY ROUTER 7 / 19 Disconnect e lectrical power hydraulic and air pressure b efore m aking repairs or adjustments. Do not run the machine in the watery and moist areas. Machine sh ould b e adjusted and well-kept all the time. N ever d o not work w ith broken machine. ...
-
Atech Tech LIBRA-04 M - page 8
LIBRA-04 M MANUA L COPY ROUTER 8 / 19 III –MACHINE DESCRIPTIO N LIBRA -04 M Ma nual Cop y R outer is used for m illing lock holes, hi nge slots, and handle mounting h oles on to vin yl (PVC) and aluminum profiles. LIBRA-04 M Picture 3-1 General View Milling Group ...
-
Atech Tech LIBRA-04 M - page 9
...
-
Atech Tech LIBRA-04 M - page 10
LIBRA-04 M MANUA L COPY ROUTER 10 / 19 IV – INSTALLATIO N The Libra- 04 M Ma nual Cop y R outer is f actory tested t o ensure that th e electrical system and all mechanical comp onents work properly. All material and spar e parts se nt from the factor y have been thoroughl y checked b efore co nsignment t o the t ransportation agency. On receivin ...
-
Atech Tech LIBRA-04 M - page 11
LIBRA-04 M MANUAL COPY ROUTER 11 / 19 IV.2 – THE RE QUIRED OPE RATION ZONE ATech recomm end s a minimum of 100 cm (40”) clearance on the front, a minimum of 30 cm (12”) clearance at the back side of the entire assembly and a minimum of 150 cm (59”) clearance on the sides. The follo w ing figure shows the recomm ende d minimum saf e operatio ...
-
Atech Tech LIBRA-04 M - page 12
LIBRA-04 M MANUAL COPY ROUTER 12 / 19 Pressure for air s hould read 6 to 8 ba r (90-120 psi). Us ing hose with a large diameter may preve nt loose of air pressur e along the long line. A lso the air should never contain moisture to not damage to the valves and pist ons. Machine should be b alanced. A go od balanced machine increases p roduction qua ...
-
Atech Tech LIBRA-04 M - page 13
LIBRA-04 M MANUAL COPY ROUTER 13 / 19 V – RUNNING T H E MACHINE Figure 5-1 Machine p arts ...
-
Atech Tech LIBRA-04 M - page 14
LIBRA-04 M MANUAL COPY ROUTER 14 / 19 MILLING PROCESS Turn on the main po wer switch, put the pro file onto the setsquare and clamp it with the clamping pistons. The tracer pin must be placed i nto the template which is to b e copied. Copy motor is run. Set the drill bit (router bit) i nto profile by copy vertical moveme nt handle. Deep drillin g i ...
-
Atech Tech LIBRA-04 M - page 15
LIBRA-04 M MANUAL COPY ROUTER 15 / 19 Electric cabinet should be cleaned from dust and shaving with air once in six months. • If clamp pistons d o not press the p rofile, pressur e sh ould be c ontrolled and adj usted from t he co nditioner. Machine needs at least 6 bar (90 psi) air pressur e. Make sure to maintain this. VII – TABLE OF PROB ...
-
Atech Tech LIBRA-04 M - page 16
LIBRA-04 M MANUAL COPY ROUTER 16 / 19 If the machine seems like normal completel y, read the user guide a gain by running the machine with t he m ethod of finding out the break down step by step. If pro blem sti ll occurs, call the servic e. ...
-
Atech Tech LIBRA-04 M - page 17
LIBRA-04 M MANUAL COPY ROUTER 17 / 19 VIII – CIRCUIT DIAGRAM VIII.1 – PNEU MATIC CIRCUIT ...
-
Atech Tech LIBRA-04 M - page 18
LIBRA-04 M MANUAL COPY ROUTER 18 / 19 VIII.2 –ELEC TRIC CIRCUIT ...
-
Atech Tech LIBRA-04 M - page 19
LIBRA-04 M MANUAL COPY ROUTER 19 / 19 ...
¿Tienes una pregunta acerca de Atech Tech LIBRA-04 M?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Atech Tech LIBRA-04 M, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Atech Tech LIBRA-04 M probablemente compartirá una forma de solucionarlo.