Français dropdown-ico

Manuel d’utilisation Dell 350

40 pages 1.3 mb
Télécharger

Aller à la page of 40

Summary
  • Dell 350 - page 1

    DellPrecision™Workstation350ServiceManual Notes, Notices, and Cautions Information in this document is subject to change without notice. © 2003DellComputerCorporation.Allrightsreserved. Reproduction in any manner whatsoever without the written permission of Dell Computer Corporation is strictly forbidden. Trad ...

  • Dell 350 - page 2

    Back to Contents Page Battery DellPrecision™Workstation350ServiceManual  Replacing the Battery  A coin - cell battery maintains computer configuration, date, and time information. The battery can last several years.  The battery may need replacing if you have repeatedly reset the time and date information after turning on ...

  • Dell 350 - page 3

     10.  Close the computer cover and connect your computer and devices to electrical outlets. 11.  Enter system setup and restore the settings you recorded before beginning this procedure. 12.  Properly dispose of the old battery. For more information see your System Information Guide . Back to Contents Page  NOTICE: To connect a netwo ...

  • Dell 350 - page 4

    Back to Contents Page Before You Begin DellPrecision™Workstation350ServiceManual  Thissectionprovidesproceduresforremovingandreplacingthecomponents,assemblies,andsubassembliesintheDellPrecision™350computer.Unless otherwise noted, each procedure assumes that the follow ...

  • Dell 350 - page 5

     ...

  • Dell 350 - page 6

    Back to Contents Page Chassis Intrusion Switch DellPrecision™Workstation350ServiceManual  Removing the Chassis Intrusion Switch  1.  Disconnect the chassis intrusion switch cable connector from the control panel on the front of the chassis.  Note the routing of the chassis intrusion cable as you remove it from the chass ...

  • Dell 350 - page 7

    Back to Contents Page Control Panel DellPrecision™Workstation350ServiceManual    Removing the Control Panel 1.  To remove the top and bottom panels of the computer, remove any installed CD drives and release all the tabs on each panel.   2.  To prepare the computer cover for removal, release the three computer ...

  • Dell 350 - page 8

    Replacing the Control Panel  Follow the steps in the " Removing the Control Panel " procedure in the reverse order, ensuring that all tabs are secure.  Back to Contents Page  ...

  • Dell 350 - page 9

    Back to Contents Page Control Panel DellPrecision™Workstation350ServiceManual    Removing the Control Panel 1.  To remove the top and bottom panels of the computer, remove any installed CD drives and release all the tabs on each panel.   2.  To prepare the computer cover for removal, release the three computer ...

  • Dell 350 - page 10

    Replacing the Control Panel  Follow the steps in the " Removing the Control Panel " procedure in the reverse order, ensuring that all tabs are secure.  Back to Contents Page  ...

  • Dell 350 - page 11

    Back to Contents Page I/O Panel DellPrecision™Workstation350ServiceManual  Removing the I/O Panel   1.  Disconnect the control - panel cable from the control - panel connector on the I/O panel. Disconnect the I/O cable from the I/O panel.  Note the routing of the control - panel cable as you remove it from the comput ...

  • Dell 350 - page 12

    Back to Contents Page Memory DellPrecision™Workstation350ServiceManual   You can increase your computer memory by installing memory modules on the system board. For information on the type of memory supported by your computer, see "Specifications" in your User's Guide . Memory Installation Guidelines l  Befo ...

  • Dell 350 - page 13

    Removing a Memory Module 1.  Press out the securing clip at each end of the memory module connector. 2.  Grasp the module and pull up.  If the module is difficult to remove, gently ease the module back and forth to remove it from the connector. Installing a Memory Module 1.  Press out the securing clip at each end of the memory module c ...

  • Dell 350 - page 14

     ...

  • Dell 350 - page 15

    Back to Contents Page AGP Card DellPrecision™Workstation350ServiceManual  Removing an AGP Card 1.  Some AGP cards require a power cable. If the card has a power cable attached to it, disconnect the cable from the card. 2.  Remove the filler bracket by raising the hinged lever and sliding the bracket up.   3.  Pres ...

  • Dell 350 - page 16

     7.  Connect your computer and devices to electrical outlets, and turn them on.  Back to Contents Page  NOTICE: To connect a network cable, first plug the cable into the network wall jack and then plug it into the computer. ...

  • Dell 350 - page 17

    Back to Contents Page PCI Cards DellPrecision™Workstation350ServiceManual   Your computer provides four slots for 32 - bit 33 - MHz cards. For more information, see "Specifications" in your User's Guide or " System Board " in this document.   If you are installing or replacing a card, follow the ...

  • Dell 350 - page 18

      8.  Before you lower the retention arm, ensure that: l  The tops of all cards and filler brackets are flush with the alignment bar l  The notch in the top of the card or filler bracket fits around the alignment guide  Press the arm into place, securing the card(s) in the computer.    9.  Connect any cables that shoul ...

  • Dell 350 - page 19

    10.  Close the computer cover , reconnect the computer and devices to electrical outlets, and turn them on. 11.  If you installed a sound card: a.  Enter system setup, go to Integrated Devices , and change the setting for Sound to Off . b.  Connect external audio devices to the sound card's connectors. Do not connect external audio ...

  • Dell 350 - page 20

    ...

  • Dell 350 - page 21

    Back to Contents Page Closing the Computer Cover DellPrecision™Workstation350ServiceManual 1.  Ensure that all cables are connected, and fold cables out of the way.  Gently pull the power cables toward you so that they do not get caught underneath the drives. 2.  Ensure that no tools or extra parts are left inside the comp ...

  • Dell 350 - page 22

    Back to Contents Page Opening the Computer Cover DellPrecision™Workstation350ServiceManual  1.  Shut down the computer through the Start menu. 2.  Ensure that your computer and attached devices are turned off. If your computer and attached devices did not automatically turn off when you shut down your computer, turn them o ...

  • Dell 350 - page 23

    Back to Contents Page Drives DellPrecision™Workstation350ServiceManual  Overview  Your computer supports: l  Two hard drives l  Two floppy drives l  Two CD or DVD drives   IDE Drive Addressing  When you connect two IDE devices to a single IDE interface cable and configure them for the cable select setting, t ...

  • Dell 350 - page 24

       Most interface connectors are keyed for correct insertion; that is, a notch or a missing pin on one connector matches a tab or a filled - in hole on the other connector. Keyed connectors ensure that the pin - 1 wire in the cable (indicated by the colored stripe along one edge of the cable) goes to the pin - 1 end of the connector. The p ...

  • Dell 350 - page 25

     Installing a Hard Drive 1.  Unpack the replacement hard drive, and prepare it for installation. 2.  Check the documentation for the drive to verify that it is configured for your computer. 3.  If your replacement hard drive does not have the bracket rails attached, remove the rails from the old drive by removing the two screws that sec ...

  • Dell 350 - page 26

     6.  Check all connectors to be certain that they are properly cabled and firmly seated. 7.  Close the computer cover .  8.  Connect your computer and devices to electrical outlets, and turn them on.  See the documentation that came with the drive for instructions on installing any software required for drive operation. 9.  If ...

  • Dell 350 - page 27

      6.  Connect a power cable to the drive.  7.  Locate the extra connector on the drive cable that is attached to your first hard drive and attach the connector to the second hard drive.  Your computer uses cable - select drive cables. This means that the device connected to the end connector of the drive cable is the master device ...

  • Dell 350 - page 28

    Front - Panel Inserts   If you are installing a new floppy or CD/DVD drive rather than replacing a drive, remove the front - panel inserts. 1.  Open the computer cover to a 90 - degree angle and release the insert tabs from inside the computer.  2.  Press on the insert until it pops free of the front panel cover.  Removing a Flopp ...

  • Dell 350 - page 29

     3.  Press inward on the two tabs on the sides of the drive, slide the drive upward, and remove it from the floppy - drive bay.  Installing a Floppy Drive 1.  If you are replacing a drive and the new drive does not have the bracket rails attached, remove the rails from the old drive by removing the two screws that secure each rail to th ...

  • Dell 350 - page 30

    3.  Attach the power and floppy - drive cables to the floppy drive. 4.  Connect the other end of the floppy - drive cable to the connector labeled "FLOPPY" on the system board.   5.  If you are installing a new floppy drive rather than replacing a drive, remove the front - panel inserts . 6.  Check all cable connections, ...

  • Dell 350 - page 31

     2.  Press inward on the two tabs on the sides of the drive, and then slide the drive upward and remove it from the drive bay.  Installing a CD/DVD Drive 1.  If you are installing a new drive, unpack the drive and prepare it for installation.  Check the documentation that accompanied the drive to verify that the drive is configured f ...

  • Dell 350 - page 32

     4.  Gently slide the drive into place until the tabs securely click into position. 5.  If you are installing a drive that has its own controller card, install the controller card in a card slot.  See the documentation that accompanied the drive and controller card to verify that the configuration is correct for your computer. Change an ...

  • Dell 350 - page 33

    Back to Contents Page  ...

  • Dell 350 - page 34

    Back to Contents Page Microprocessor DellPrecision™Workstation350ServiceManual  Removing the Microprocessor 1.  Disconnect the cooling fan power cable from the FAN connector on the system board. 2.  Disconnect the power cable from the 12VPOWER connector on the system board. 3.  Lift up the airflow shroud.  4.  Rem ...

  • Dell 350 - page 35

       5.  Pull the release lever straight up until the microprocessor is released.    6.  Remove the microprocessor from the socket. 1 securing clip (2) 2 latch (2) 3 heat sink 4 microprocessor socket 5 retention base NOTICE: Lay the heat sink down with the thermal grease facing upward. NOTICE: If you are installing a microproc ...

  • Dell 350 - page 36

     Leave the release lever extended in the release position so that the socket is ready for the new microprocessor. Installing the Microprocessor  1.  If the release lever is not extended to the release position, move it to that position. 2.  Align pin - 1 (the imprinted corner) of the microprocessor and pin - 1 of the socket.    ...

  • Dell 350 - page 37

    Back to Contents Page Power Supply DellPrecision™Workstation350ServiceManual  Removing the Power Supply  1.  Disconnect the AC power cable from the back of the power supply. 2.  Disconnect the DC power cables from the system board and the drives.  Note the routing of the DC power cables underneath the clips in the co ...

  • Dell 350 - page 38

    Back to Contents Page System Board DellPrecision™Workstation350ServiceManual  System Board Components   System Board Jumpers  CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the System Information Guide . 1 floppy drive connector (FLOPPY) 10 PCI card connectors (PCI1, P ...

  • Dell 350 - page 39

    System - Board Jumper Settings  Removing the System Board   1.  Remove any components that restrict access to the system board. 2.  Disconnect all cables from the system board. 3.  Before you remove the existing system board, visually compare the replacement system board to the existing system board to make sure that you have the ...

  • Dell 350 - page 40

    1.  Transfer components from the existing system board to the replacement system board. 2.  Remove the memory modules and install them on the replacement board.  3.  Remove the heat - sink assembly and microprocessor from the existing system board and transfer them to the replacement system board. 4.  Configure the settings of the re ...

Fabricant Dell Catégorie Personal Computer

Les documents que nous recevons du fabricant de l'appareilDell 350 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Dell
- manuels d’utilisations 350
- fiches produit Dell
- dépliants
- ou étiquettes-énergie Dell 350
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Dell 350.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Dell 350, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Dell 350. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Dell 350.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Dell 350, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Dell 350 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Dell 350.

Le manuel d’utilisation complet Dell, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Dell 350 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Dell 350, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lDell 350 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Dell 350 - qui devraient nous aider dans les premières étapes lors de l'utilisation Dell 350
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Dell 350
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Dell 350 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Dell 350?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Dell 350, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Dell 350 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)