Italiano dropdown-ico

Manuale per l’uso Dell 350

40 pagine 1.3 mb
Scarica

Vai alla pagina of 40

Summary
  • Dell 350 - page 1

    DellPrecision™Workstation350ServiceManual Notes, Notices, and Cautions Information in this document is subject to change without notice. © 2003DellComputerCorporation.Allrightsreserved. Reproduction in any manner whatsoever without the written permission of Dell Computer Corporation is strictly forbidden. Trad ...

  • Dell 350 - page 2

    Back to Contents Page Battery DellPrecision™Workstation350ServiceManual  Replacing the Battery  A coin - cell battery maintains computer configuration, date, and time information. The battery can last several years.  The battery may need replacing if you have repeatedly reset the time and date information after turning on ...

  • Dell 350 - page 3

     10.  Close the computer cover and connect your computer and devices to electrical outlets. 11.  Enter system setup and restore the settings you recorded before beginning this procedure. 12.  Properly dispose of the old battery. For more information see your System Information Guide . Back to Contents Page  NOTICE: To connect a netwo ...

  • Dell 350 - page 4

    Back to Contents Page Before You Begin DellPrecision™Workstation350ServiceManual  Thissectionprovidesproceduresforremovingandreplacingthecomponents,assemblies,andsubassembliesintheDellPrecision™350computer.Unless otherwise noted, each procedure assumes that the follow ...

  • Dell 350 - page 5

     ...

  • Dell 350 - page 6

    Back to Contents Page Chassis Intrusion Switch DellPrecision™Workstation350ServiceManual  Removing the Chassis Intrusion Switch  1.  Disconnect the chassis intrusion switch cable connector from the control panel on the front of the chassis.  Note the routing of the chassis intrusion cable as you remove it from the chass ...

  • Dell 350 - page 7

    Back to Contents Page Control Panel DellPrecision™Workstation350ServiceManual    Removing the Control Panel 1.  To remove the top and bottom panels of the computer, remove any installed CD drives and release all the tabs on each panel.   2.  To prepare the computer cover for removal, release the three computer ...

  • Dell 350 - page 8

    Replacing the Control Panel  Follow the steps in the " Removing the Control Panel " procedure in the reverse order, ensuring that all tabs are secure.  Back to Contents Page  ...

  • Dell 350 - page 9

    Back to Contents Page Control Panel DellPrecision™Workstation350ServiceManual    Removing the Control Panel 1.  To remove the top and bottom panels of the computer, remove any installed CD drives and release all the tabs on each panel.   2.  To prepare the computer cover for removal, release the three computer ...

  • Dell 350 - page 10

    Replacing the Control Panel  Follow the steps in the " Removing the Control Panel " procedure in the reverse order, ensuring that all tabs are secure.  Back to Contents Page  ...

  • Dell 350 - page 11

    Back to Contents Page I/O Panel DellPrecision™Workstation350ServiceManual  Removing the I/O Panel   1.  Disconnect the control - panel cable from the control - panel connector on the I/O panel. Disconnect the I/O cable from the I/O panel.  Note the routing of the control - panel cable as you remove it from the comput ...

  • Dell 350 - page 12

    Back to Contents Page Memory DellPrecision™Workstation350ServiceManual   You can increase your computer memory by installing memory modules on the system board. For information on the type of memory supported by your computer, see "Specifications" in your User's Guide . Memory Installation Guidelines l  Befo ...

  • Dell 350 - page 13

    Removing a Memory Module 1.  Press out the securing clip at each end of the memory module connector. 2.  Grasp the module and pull up.  If the module is difficult to remove, gently ease the module back and forth to remove it from the connector. Installing a Memory Module 1.  Press out the securing clip at each end of the memory module c ...

  • Dell 350 - page 14

     ...

  • Dell 350 - page 15

    Back to Contents Page AGP Card DellPrecision™Workstation350ServiceManual  Removing an AGP Card 1.  Some AGP cards require a power cable. If the card has a power cable attached to it, disconnect the cable from the card. 2.  Remove the filler bracket by raising the hinged lever and sliding the bracket up.   3.  Pres ...

  • Dell 350 - page 16

     7.  Connect your computer and devices to electrical outlets, and turn them on.  Back to Contents Page  NOTICE: To connect a network cable, first plug the cable into the network wall jack and then plug it into the computer. ...

  • Dell 350 - page 17

    Back to Contents Page PCI Cards DellPrecision™Workstation350ServiceManual   Your computer provides four slots for 32 - bit 33 - MHz cards. For more information, see "Specifications" in your User's Guide or " System Board " in this document.   If you are installing or replacing a card, follow the ...

  • Dell 350 - page 18

      8.  Before you lower the retention arm, ensure that: l  The tops of all cards and filler brackets are flush with the alignment bar l  The notch in the top of the card or filler bracket fits around the alignment guide  Press the arm into place, securing the card(s) in the computer.    9.  Connect any cables that shoul ...

  • Dell 350 - page 19

    10.  Close the computer cover , reconnect the computer and devices to electrical outlets, and turn them on. 11.  If you installed a sound card: a.  Enter system setup, go to Integrated Devices , and change the setting for Sound to Off . b.  Connect external audio devices to the sound card's connectors. Do not connect external audio ...

  • Dell 350 - page 20

    ...

  • Dell 350 - page 21

    Back to Contents Page Closing the Computer Cover DellPrecision™Workstation350ServiceManual 1.  Ensure that all cables are connected, and fold cables out of the way.  Gently pull the power cables toward you so that they do not get caught underneath the drives. 2.  Ensure that no tools or extra parts are left inside the comp ...

  • Dell 350 - page 22

    Back to Contents Page Opening the Computer Cover DellPrecision™Workstation350ServiceManual  1.  Shut down the computer through the Start menu. 2.  Ensure that your computer and attached devices are turned off. If your computer and attached devices did not automatically turn off when you shut down your computer, turn them o ...

  • Dell 350 - page 23

    Back to Contents Page Drives DellPrecision™Workstation350ServiceManual  Overview  Your computer supports: l  Two hard drives l  Two floppy drives l  Two CD or DVD drives   IDE Drive Addressing  When you connect two IDE devices to a single IDE interface cable and configure them for the cable select setting, t ...

  • Dell 350 - page 24

       Most interface connectors are keyed for correct insertion; that is, a notch or a missing pin on one connector matches a tab or a filled - in hole on the other connector. Keyed connectors ensure that the pin - 1 wire in the cable (indicated by the colored stripe along one edge of the cable) goes to the pin - 1 end of the connector. The p ...

  • Dell 350 - page 25

     Installing a Hard Drive 1.  Unpack the replacement hard drive, and prepare it for installation. 2.  Check the documentation for the drive to verify that it is configured for your computer. 3.  If your replacement hard drive does not have the bracket rails attached, remove the rails from the old drive by removing the two screws that sec ...

  • Dell 350 - page 26

     6.  Check all connectors to be certain that they are properly cabled and firmly seated. 7.  Close the computer cover .  8.  Connect your computer and devices to electrical outlets, and turn them on.  See the documentation that came with the drive for instructions on installing any software required for drive operation. 9.  If ...

  • Dell 350 - page 27

      6.  Connect a power cable to the drive.  7.  Locate the extra connector on the drive cable that is attached to your first hard drive and attach the connector to the second hard drive.  Your computer uses cable - select drive cables. This means that the device connected to the end connector of the drive cable is the master device ...

  • Dell 350 - page 28

    Front - Panel Inserts   If you are installing a new floppy or CD/DVD drive rather than replacing a drive, remove the front - panel inserts. 1.  Open the computer cover to a 90 - degree angle and release the insert tabs from inside the computer.  2.  Press on the insert until it pops free of the front panel cover.  Removing a Flopp ...

  • Dell 350 - page 29

     3.  Press inward on the two tabs on the sides of the drive, slide the drive upward, and remove it from the floppy - drive bay.  Installing a Floppy Drive 1.  If you are replacing a drive and the new drive does not have the bracket rails attached, remove the rails from the old drive by removing the two screws that secure each rail to th ...

  • Dell 350 - page 30

    3.  Attach the power and floppy - drive cables to the floppy drive. 4.  Connect the other end of the floppy - drive cable to the connector labeled "FLOPPY" on the system board.   5.  If you are installing a new floppy drive rather than replacing a drive, remove the front - panel inserts . 6.  Check all cable connections, ...

  • Dell 350 - page 31

     2.  Press inward on the two tabs on the sides of the drive, and then slide the drive upward and remove it from the drive bay.  Installing a CD/DVD Drive 1.  If you are installing a new drive, unpack the drive and prepare it for installation.  Check the documentation that accompanied the drive to verify that the drive is configured f ...

  • Dell 350 - page 32

     4.  Gently slide the drive into place until the tabs securely click into position. 5.  If you are installing a drive that has its own controller card, install the controller card in a card slot.  See the documentation that accompanied the drive and controller card to verify that the configuration is correct for your computer. Change an ...

  • Dell 350 - page 33

    Back to Contents Page  ...

  • Dell 350 - page 34

    Back to Contents Page Microprocessor DellPrecision™Workstation350ServiceManual  Removing the Microprocessor 1.  Disconnect the cooling fan power cable from the FAN connector on the system board. 2.  Disconnect the power cable from the 12VPOWER connector on the system board. 3.  Lift up the airflow shroud.  4.  Rem ...

  • Dell 350 - page 35

       5.  Pull the release lever straight up until the microprocessor is released.    6.  Remove the microprocessor from the socket. 1 securing clip (2) 2 latch (2) 3 heat sink 4 microprocessor socket 5 retention base NOTICE: Lay the heat sink down with the thermal grease facing upward. NOTICE: If you are installing a microproc ...

  • Dell 350 - page 36

     Leave the release lever extended in the release position so that the socket is ready for the new microprocessor. Installing the Microprocessor  1.  If the release lever is not extended to the release position, move it to that position. 2.  Align pin - 1 (the imprinted corner) of the microprocessor and pin - 1 of the socket.    ...

  • Dell 350 - page 37

    Back to Contents Page Power Supply DellPrecision™Workstation350ServiceManual  Removing the Power Supply  1.  Disconnect the AC power cable from the back of the power supply. 2.  Disconnect the DC power cables from the system board and the drives.  Note the routing of the DC power cables underneath the clips in the co ...

  • Dell 350 - page 38

    Back to Contents Page System Board DellPrecision™Workstation350ServiceManual  System Board Components   System Board Jumpers  CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the System Information Guide . 1 floppy drive connector (FLOPPY) 10 PCI card connectors (PCI1, P ...

  • Dell 350 - page 39

    System - Board Jumper Settings  Removing the System Board   1.  Remove any components that restrict access to the system board. 2.  Disconnect all cables from the system board. 3.  Before you remove the existing system board, visually compare the replacement system board to the existing system board to make sure that you have the ...

  • Dell 350 - page 40

    1.  Transfer components from the existing system board to the replacement system board. 2.  Remove the memory modules and install them on the replacement board.  3.  Remove the heat - sink assembly and microprocessor from the existing system board and transfer them to the replacement system board. 4.  Configure the settings of the re ...

Fabbricante Dell Categoria Personal Computer

I documenti che otteniamo dal fabbricante del dispositivoDell 350 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Dell
- manuali per l’uso 350
- schede prodotto Dell
- opuscoli
- o etichette energetiche Dell 350
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Dell 350.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Dell 350, manuali di manutenzione, brevi manuali o manuali utente Dell 350. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Dell 350.

Manuali per l’uso simili

Manuale completo del dispositivo Dell 350, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Dell 350 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Dell 350.

Il manuale per l’uso completo Dell, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Dell 350 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Dell 350, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Dell 350 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Dell 350 - che ci dovrebbe aiutare nei primi passi durante l'uso Dell 350
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Dell 350
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Dell 350 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Dell 350?

Utilizza il modulo sottostante

Se non hai risolto il problema con Dell 350 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Dell 350 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)