Français dropdown-ico

Manuel d’utilisation Porter-Cable 38129

23 pages 2.97 mb
Télécharger

Aller à la page of 23

Summary
  • Porter-Cable 38129 - page 1

    ESP AÑOL: PÁGINA 23 FRANÇAISE : P AGE 43 Double Insulated 1 0" Bench T op T able Saw Instruction Manual Part No. 912933 - 09-15-03 The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for futur e refer ence. Model No. _____________________________________ T ype ______ ...

  • Porter-Cable 38129 - page 2

    2 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury . Used without the saf ...

  • Porter-Cable 38129 - page 3

    3 1. FOR YOUR OWN SAFETY , READ THE INSTRUC- TION MANUAL BEFORE OPERA TING THE MACHINE. Learning the machine’ s application, limitations, and specific hazards will gr eatly minimize the possibility of accidents and injury . 2. USE CERTIFIED SAFETY EQUIPMENT . Eye protection equipment should comply with ANSI Z87.1 standards, hearing equipment shou ...

  • Porter-Cable 38129 - page 4

    4 ADDITIONAL SAFETY RULES FOR T ABLE SA WS 1 . DO NOT OPERA TE THIS MACHINE until it is assembled and installed according to the instructions. 2. OBT AIN ADVICE FROM YOUR SUPERVISOR, instructor , or another qualified person if you are not familiar with the operation of this machine. 3. FOLLOW ALL WIRING CODES and recommended electrical connections. ...

  • Porter-Cable 38129 - page 5

    5 FOREWORD The Porter -Cable Model 3812 is a 10" Bench T op T able Saw . The saw comes with a 26"x20" table surface with a rip fence extension wing which provides a 24½" rip capacity for ripping 4x8 sheets. The Model 3812 comes with a Riptide™ 24 tooth carbide-tipped blade, miter gauge, rip fence, quick release blade guar d, ...

  • Porter-Cable 38129 - page 6

    6 CAR TON CONTENTS Fig. 2 1 2 3 4 5 6 7 8 9 1. Saw 2. Fence 3. T able Insert 4. Blade Guard and Spreader Assembly 5. Blade Wrench (2) 6. Miter Gauge 7. Anchor Block Shim (3) 8. Handle 9. 1/4"-20x1-3/4" Screw ...

  • Porter-Cable 38129 - page 7

    7 ASSEMBL Y BLADE RAISING AND LOWERING HANDWHEEL Insert the 1-3/4" screw (D) Fig. 4, thr ough handle (E). Assemble handle (E) to handwheel (A) by threading screw (D) clockwise into handwheel as shown in Fig. 5. Handle (E) should rotate fr eely on screw (D). Fig. 4 Fig. 5 BLADE GUARD AND SPREADER ASSEMBL Y 1. DISCONNECT MACHINE FROM POWER SOURC ...

  • Porter-Cable 38129 - page 8

    8 6. NOTE: The anchor block (B) Fig. 6, has been adjusted at the factory so that the spreader will be aligned with the saw blade which is supplied with the saw . When changing to blades with dif ferent widths it may be necessary to adjust the anchor block (B) Fig. 9, as follows: 7. Remove table insert and saw blade. 8. Loosen the two screws (C) Fig ...

  • Porter-Cable 38129 - page 9

    9 RIP FENCE TO SA W T ABLE 1. The rip fence may be used on the right or left hand side of the saw table. Lift locking handle (A) Fig. 12, and position the front end of the fence on the fr ont fence rail as shown. 2. While pressing front end of fence firmly against fr ont fence rail, place rear end of fence down on the r ear fence rail and push down ...

  • Porter-Cable 38129 - page 10

    10 OPERA TING CONTROLS AND ADJUSTMENTS ST AR TING AND STOPPING SA W The “ON/OFF” switch (A) Fig 16, is located on the front of the saw cabinet. T o tur n the saw “ON” pull the “ON/OFF” switch (A) out. T o tur n the saw “OFF”, push in on the “ON/OFF” switch (A). Fig. 16 A SOFT ST AR T Model 3812 has a “Soft Start” feature des ...

  • Porter-Cable 38129 - page 11

    11 ADJUSTING 0 AND 45 DEGREE POSITIVE STOPS Y our saw is equipped with positive stops for rapid and accurate positioning of the saw blade at 0 and 45 degrees to the table. This saw has the capability to go 2 degrees beyond 0 and 45 degr ees (-2º to 47º). T o adjust the positive stops, proceed as follows: 1. DISCONNECT MACHINE FROM POWER SOURCE. 2 ...

  • Porter-Cable 38129 - page 12

    12 RIPPING THIN STOCK T o adjust the fence, pull up on lever (B) so that the top of the rip fence can be removed, and r epositioned on the rip fence as shown in Fig. 25. This is only necessary when the fence guide rails are extended. When using the guide rails for ripping, the fence must be positioned as shown in Fig. 25, so that the wood can rest ...

  • Porter-Cable 38129 - page 13

    13 MITER GAGE OPERA TION AND ADJUSTMENTS When straight cross-cutting (blade set 90 degr ees to the table) the miter gage can be used in either table slot. When bevel cross-cutting (blade tilted) only use the miter gage in the right table slot where the blade is tilted away from the miter gage and your hands. This miter gage is equipped with individ ...

  • Porter-Cable 38129 - page 14

    14 Cross-cutting r equires the use of the miter gage to position and guide the work. Place the work against the miter gage and advance both the gage and work toward the saw blade, as shown in Fig. 32. The miter gage may be used in either table slot. When bevel cutting (blade tilted), use the miter gage slot that does not cause interference of your ...

  • Porter-Cable 38129 - page 15

    15 If the ripped work is less than 4 inches wide, a PUSH STICK should always be used to complete the feed, as shown in Fig. 35. The PUSH STICK can easily be made from scrap material as explained in the section “CONSTRUCTING PUSH STICK.” When ripping stock 2 inches or narrower , assemble an auxiliary wood facing to the fence, as explained in the ...

  • Porter-Cable 38129 - page 16

    16 The dado head set (D) Fig. 40, is assembled to the saw arbor as shown. IMPORT ANT : The blade guard and splitter assembly cannot be used when dadoing and must be removed. Auxiliary jigs, fixtur es, push sticks and feather boards should also be used. Also, the accessory dado head table insert Delta model 38122 (E) Fig. 40, must be used in place o ...

  • Porter-Cable 38129 - page 17

    MAINTENANCE CHANGING THE BLADE 1. DISCONNECT MACHINE FROM POWER SOURCE. USE ONL Y 10" DIAMETER SAW BLADES RA TED FOR 4600 RPM OR HIGHER WITH 5/8" ARBOR HOLES. 2. Remove the table insert (A) Fig. 44, and raise the saw blade to its maximum height. 3. Remove the blade guard and spr eader assembly . NOTE: THE BLADE MUST BE IN THE 90 DEGREE PO ...

  • Porter-Cable 38129 - page 18

    18 SERVICE AND REP AIRS All quality tools will eventually requir e servicing or replacement of parts due to wear fr om normal use. These operations, including brush inspection and replacement, should ONL Y be performed by either an AUTHORIZED PORTER-CABLE SERVICE ST A TION or a POR TER-CABLE • DEL T A F ACTOR Y SERVICE CENTER. All r epairs made b ...

  • Porter-Cable 38129 - page 19

    19 19 PUSH STICK MAKE FROM 1/2" OR 3/4" WOOD OR THICKNESS LESS THAN WIDTH OF MA T’L. TO BE CUT CUT OFF HERE TO PUSH 1/4" WOOD CUT OFF HERE TO PUSH 1/2" WOOD NOTCH TO HELP PREVENT HAND FROM SLIPPING 1/2" SQUARES CONSTRUCTING A PUSH STICK When ripping work less than 4 inches wide, a push stick should be used to complete the ...

  • Porter-Cable 38129 - page 20

    20 NOTES ...

  • Porter-Cable 38129 - page 21

    21 NOTES ...

  • Porter-Cable 38129 - page 22

    22 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter -Cable warrants its Professional Power T ools for a period of one year from the date of original purchase. W e will r epair or replace at our option, any part or parts of the product and accessories covered under this warranty which, after examination, proves to be defective in workmanship or materia ...

  • Porter-Cable 38129 - page 23

    The following are trademarks of PORTER-CABLE • DEL T A (Las siguientes son marcas registradas de PORTER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL T A ...

Fabricant Porter-Cable Catégorie Saw

Les documents que nous recevons du fabricant de l'appareilPorter-Cable 38129 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Porter-Cable
- manuels d’utilisations 38129
- fiches produit Porter-Cable
- dépliants
- ou étiquettes-énergie Porter-Cable 38129
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Porter-Cable 38129.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Porter-Cable 38129, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Porter-Cable 38129. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Porter-Cable 38129.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Porter-Cable 38129, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Porter-Cable 38129 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Porter-Cable 38129.

Le manuel d’utilisation complet Porter-Cable, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Porter-Cable 38129 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Porter-Cable 38129, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lPorter-Cable 38129 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Porter-Cable 38129 - qui devraient nous aider dans les premières étapes lors de l'utilisation Porter-Cable 38129
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Porter-Cable 38129
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Porter-Cable 38129 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Porter-Cable 38129?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Porter-Cable 38129, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Porter-Cable 38129 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)