Porter-Cable 38129の取扱説明書

23ページ 2.97 mb
ダウンロード

ページに移動 of 23

Summary
  • Porter-Cable 38129 - page 1

    ESP AÑOL: PÁGINA 23 FRANÇAISE : P AGE 43 Double Insulated 1 0" Bench T op T able Saw Instruction Manual Part No. 912933 - 09-15-03 The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for futur e refer ence. Model No. _____________________________________ T ype ______ ...

  • Porter-Cable 38129 - page 2

    2 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury . Used without the saf ...

  • Porter-Cable 38129 - page 3

    3 1. FOR YOUR OWN SAFETY , READ THE INSTRUC- TION MANUAL BEFORE OPERA TING THE MACHINE. Learning the machine’ s application, limitations, and specific hazards will gr eatly minimize the possibility of accidents and injury . 2. USE CERTIFIED SAFETY EQUIPMENT . Eye protection equipment should comply with ANSI Z87.1 standards, hearing equipment shou ...

  • Porter-Cable 38129 - page 4

    4 ADDITIONAL SAFETY RULES FOR T ABLE SA WS 1 . DO NOT OPERA TE THIS MACHINE until it is assembled and installed according to the instructions. 2. OBT AIN ADVICE FROM YOUR SUPERVISOR, instructor , or another qualified person if you are not familiar with the operation of this machine. 3. FOLLOW ALL WIRING CODES and recommended electrical connections. ...

  • Porter-Cable 38129 - page 5

    5 FOREWORD The Porter -Cable Model 3812 is a 10" Bench T op T able Saw . The saw comes with a 26"x20" table surface with a rip fence extension wing which provides a 24½" rip capacity for ripping 4x8 sheets. The Model 3812 comes with a Riptide™ 24 tooth carbide-tipped blade, miter gauge, rip fence, quick release blade guar d, ...

  • Porter-Cable 38129 - page 6

    6 CAR TON CONTENTS Fig. 2 1 2 3 4 5 6 7 8 9 1. Saw 2. Fence 3. T able Insert 4. Blade Guard and Spreader Assembly 5. Blade Wrench (2) 6. Miter Gauge 7. Anchor Block Shim (3) 8. Handle 9. 1/4"-20x1-3/4" Screw ...

  • Porter-Cable 38129 - page 7

    7 ASSEMBL Y BLADE RAISING AND LOWERING HANDWHEEL Insert the 1-3/4" screw (D) Fig. 4, thr ough handle (E). Assemble handle (E) to handwheel (A) by threading screw (D) clockwise into handwheel as shown in Fig. 5. Handle (E) should rotate fr eely on screw (D). Fig. 4 Fig. 5 BLADE GUARD AND SPREADER ASSEMBL Y 1. DISCONNECT MACHINE FROM POWER SOURC ...

  • Porter-Cable 38129 - page 8

    8 6. NOTE: The anchor block (B) Fig. 6, has been adjusted at the factory so that the spreader will be aligned with the saw blade which is supplied with the saw . When changing to blades with dif ferent widths it may be necessary to adjust the anchor block (B) Fig. 9, as follows: 7. Remove table insert and saw blade. 8. Loosen the two screws (C) Fig ...

  • Porter-Cable 38129 - page 9

    9 RIP FENCE TO SA W T ABLE 1. The rip fence may be used on the right or left hand side of the saw table. Lift locking handle (A) Fig. 12, and position the front end of the fence on the fr ont fence rail as shown. 2. While pressing front end of fence firmly against fr ont fence rail, place rear end of fence down on the r ear fence rail and push down ...

  • Porter-Cable 38129 - page 10

    10 OPERA TING CONTROLS AND ADJUSTMENTS ST AR TING AND STOPPING SA W The “ON/OFF” switch (A) Fig 16, is located on the front of the saw cabinet. T o tur n the saw “ON” pull the “ON/OFF” switch (A) out. T o tur n the saw “OFF”, push in on the “ON/OFF” switch (A). Fig. 16 A SOFT ST AR T Model 3812 has a “Soft Start” feature des ...

  • Porter-Cable 38129 - page 11

    11 ADJUSTING 0 AND 45 DEGREE POSITIVE STOPS Y our saw is equipped with positive stops for rapid and accurate positioning of the saw blade at 0 and 45 degrees to the table. This saw has the capability to go 2 degrees beyond 0 and 45 degr ees (-2º to 47º). T o adjust the positive stops, proceed as follows: 1. DISCONNECT MACHINE FROM POWER SOURCE. 2 ...

  • Porter-Cable 38129 - page 12

    12 RIPPING THIN STOCK T o adjust the fence, pull up on lever (B) so that the top of the rip fence can be removed, and r epositioned on the rip fence as shown in Fig. 25. This is only necessary when the fence guide rails are extended. When using the guide rails for ripping, the fence must be positioned as shown in Fig. 25, so that the wood can rest ...

  • Porter-Cable 38129 - page 13

    13 MITER GAGE OPERA TION AND ADJUSTMENTS When straight cross-cutting (blade set 90 degr ees to the table) the miter gage can be used in either table slot. When bevel cross-cutting (blade tilted) only use the miter gage in the right table slot where the blade is tilted away from the miter gage and your hands. This miter gage is equipped with individ ...

  • Porter-Cable 38129 - page 14

    14 Cross-cutting r equires the use of the miter gage to position and guide the work. Place the work against the miter gage and advance both the gage and work toward the saw blade, as shown in Fig. 32. The miter gage may be used in either table slot. When bevel cutting (blade tilted), use the miter gage slot that does not cause interference of your ...

  • Porter-Cable 38129 - page 15

    15 If the ripped work is less than 4 inches wide, a PUSH STICK should always be used to complete the feed, as shown in Fig. 35. The PUSH STICK can easily be made from scrap material as explained in the section “CONSTRUCTING PUSH STICK.” When ripping stock 2 inches or narrower , assemble an auxiliary wood facing to the fence, as explained in the ...

  • Porter-Cable 38129 - page 16

    16 The dado head set (D) Fig. 40, is assembled to the saw arbor as shown. IMPORT ANT : The blade guard and splitter assembly cannot be used when dadoing and must be removed. Auxiliary jigs, fixtur es, push sticks and feather boards should also be used. Also, the accessory dado head table insert Delta model 38122 (E) Fig. 40, must be used in place o ...

  • Porter-Cable 38129 - page 17

    MAINTENANCE CHANGING THE BLADE 1. DISCONNECT MACHINE FROM POWER SOURCE. USE ONL Y 10" DIAMETER SAW BLADES RA TED FOR 4600 RPM OR HIGHER WITH 5/8" ARBOR HOLES. 2. Remove the table insert (A) Fig. 44, and raise the saw blade to its maximum height. 3. Remove the blade guard and spr eader assembly . NOTE: THE BLADE MUST BE IN THE 90 DEGREE PO ...

  • Porter-Cable 38129 - page 18

    18 SERVICE AND REP AIRS All quality tools will eventually requir e servicing or replacement of parts due to wear fr om normal use. These operations, including brush inspection and replacement, should ONL Y be performed by either an AUTHORIZED PORTER-CABLE SERVICE ST A TION or a POR TER-CABLE • DEL T A F ACTOR Y SERVICE CENTER. All r epairs made b ...

  • Porter-Cable 38129 - page 19

    19 19 PUSH STICK MAKE FROM 1/2" OR 3/4" WOOD OR THICKNESS LESS THAN WIDTH OF MA T’L. TO BE CUT CUT OFF HERE TO PUSH 1/4" WOOD CUT OFF HERE TO PUSH 1/2" WOOD NOTCH TO HELP PREVENT HAND FROM SLIPPING 1/2" SQUARES CONSTRUCTING A PUSH STICK When ripping work less than 4 inches wide, a push stick should be used to complete the ...

  • Porter-Cable 38129 - page 20

    20 NOTES ...

  • Porter-Cable 38129 - page 21

    21 NOTES ...

  • Porter-Cable 38129 - page 22

    22 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter -Cable warrants its Professional Power T ools for a period of one year from the date of original purchase. W e will r epair or replace at our option, any part or parts of the product and accessories covered under this warranty which, after examination, proves to be defective in workmanship or materia ...

  • Porter-Cable 38129 - page 23

    The following are trademarks of PORTER-CABLE • DEL T A (Las siguientes son marcas registradas de PORTER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL T A ...

メーカー Porter-Cable カテゴリー Saw

Porter-Cable 38129のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 38129の取扱説明書
- Porter-Cableの製品カード
- パンフレット
- またはPorter-Cable 38129の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Porter-Cable 38129の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Porter-Cable 38129の取り付け説明書、サービスマニュアル、簡易説明書、またはPorter-Cable 38129のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Porter-Cable 38129の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Porter-Cable 38129デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがPorter-Cable 38129を使用するのを助ける技術的文書のことです。説明書は通常、全てのPorter-Cable 38129ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Porter-Cableの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Porter-Cable 38129の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははPorter-Cable 38129の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Porter-Cable 38129に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Porter-Cable 38129デバイスの基本機能を使うにあたってのヒント。 Porter-Cable 38129のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Porter-Cable 38129に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるPorter-Cable 38129のメーカー/サービスへの連絡先に関する情報。

Porter-Cable 38129についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもPorter-Cable 38129の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPorter-Cable 38129で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)