Français dropdown-ico

Manuel d’utilisation Hellenbrand Iron Curtain System

28 pages 0.56 mb
Télécharger

Aller à la page of 28

Summary
  • Hellenbrand Iron Curtain System - page 1

    For systems manufactured after October 1997 Manufactured by: HELLENBRAND, INC. 404 Moravian Valley Road • PO Box 187 Waunakee, Wisconsin 53597 Phone: 608-849-3050 • Fax: 608-849-7398 Web: www.hellenbrand.com • Email: info@hellenbrand.com Owner ’ s Manual ©2003 TM TM ...

  • Hellenbrand Iron Curtain System - page 2

    2 Congratulations on your purchase of one of the finest water treatment systems available today – the Iron Curtain System. This patented, non-chemical filter system, when properly applied will remove iron, manganese and/or hydrogen sulfide from your water supply. The Iron Curtain has been third-party tested by the Water Quality Association. An op ...

  • Hellenbrand Iron Curtain System - page 3

    3 INST ALLA TION DA T A Date of Installation _______________________________________ Model No.___________________________________ Address of Installation ___________________________________________________________________________________ Installed By_____________________________________________________________________________________________ Raw Wa ...

  • Hellenbrand Iron Curtain System - page 4

    4 IRON CUR T AIN the way to solve this problem is to use layers of media.” The advantages of a multi-media bed are: 1. Longer runs between backwash times. 2. Caking of the bed and breakthrough of turbidity are virtually eliminated. 3. Much higher service flow rates per square foot. 4. Higher degree of clarity because of the heavier, finer filter ...

  • Hellenbrand Iron Curtain System - page 5

    5 Operating Conditions The Iron Curtain System has been validated by the WQA under their S-200 Filter Standard for the reduction/removal of iron, manganese, and/or hydrogen sulfide. The concentration limits listed below reflect the maximum individual limit that each contaminant was tested for separately without any interference of other contaminant ...

  • Hellenbrand Iron Curtain System - page 6

    6 Caution: The water pressure is not to exceed 70 p.s.i.; water temperature is not to exceed 110 ° F; conditioner cannot be subject to freezing conditions; conditioner cannot be subject to a negative pressure or vacuum. On installations where there is the possibility of a negative pressure or vacuum, a vacuum breaker or check valve must be install ...

  • Hellenbrand Iron Curtain System - page 7

    7 Instructions for Adding IC pH Correction Media See Figures 1, 2 & 3 on page 8.. 1. Place Iron Curtain System on bypass. (Close inlet and outlet valves and open bypass valve.) 2. Relieve pressure by manually advancing timer to back- wash position (see page 10). Unplug control valve after valve is shifted into backwash position and piston has s ...

  • Hellenbrand Iron Curtain System - page 8

    8 Due to existing plumbing conditions, you may want to choose an alternate installation configuration. Refer to Figures 2 and 3 below for alternate installation diagrams. FIGURE 1 Carefully place a pry bar (long screwdriver, wrench, etc.) between the screws and apply pressure clockwise until tight. Be careful not to crease or tear the o-rings in th ...

  • Hellenbrand Iron Curtain System - page 9

    9 How T o Set T imer 1 How to set days on which water conditioner is to regenerate. Rotate the skipper wheel until the number "1" is at the red pointer. Set the days that regeneration is to occur by sliding tabs on the skipper wheel outward to expose trip fingers. Each tab is one day. Tab at red pointer is tonight. Moving clockwise from t ...

  • Hellenbrand Iron Curtain System - page 10

    10 How T o Manually Regenerate Y our W ater F ilter At Any T ime Slowly turn the manual regeneration knob clockwise until the drive motor starts running. The movement of the manual regeneration knob engages the program wheel and starts the regeneration program. The black center knob will make one revolution in approximately the following three hour ...

  • Hellenbrand Iron Curtain System - page 11

    11 How T o Set Regeneration Cycle Program 1 How to set the regeneration cycle program. The regeneration cycle program on your Iron Curtain Filter has been factory preset, however, portions of the cycle or program may be lengthened or shortened to suit local conditions. To expose cycle program wheel, grasp timer in upper left- hand corner and pull, ...

  • Hellenbrand Iron Curtain System - page 12

    12 Iron Curtain System Iron Curtain Wiring Diagram 1 2 3 WHITE BLK/WHT GREEN GREEN BLACK WH WHITE BLK/WHT BROWN YELLOW RED BLACK WHITE BLK/WHT BROWN YELLOW RED BLACK BLACK BLACK BLACK BLACK/WHITE TIMER MOTOR PROGRAM ACTUATOR SWITCH AIR PUMP SWITCH BLACK BLACK BLACK PROGRAM SWITCH HOMING SWITCH VALVE DRIVE MOTOR HOMING SWITCH TO AIR PUMP (Located be ...

  • Hellenbrand Iron Curtain System - page 13

    13 Iron Curtain T imer Assembly ITEM NO. NO. REQ'D. PART NO. DESCRIPTION 1 ..................... 1 ............. 49-13870 ....... Timer Housing 2 ..................... 1 ............. 49-13011 ....... Cycle Actuator Arm 3 ..................... 1 ............. 49-49-60519 .. 24 Hour Gear 4 ..................... 1 ............. 49-13959 ....... ...

  • Hellenbrand Iron Curtain System - page 14

    14 Iron Curtain Control Drive Assembly 32 10 7 9 11 12 8 4 13 14 1 2 31 33 17 16 18 19 28 30 29 26 25 24 21 20 27 34 23 15 ITEM NO. NO. REQ'D. PART NO. DESCRIPTION 1 ..................... 1 ............. 22-01 ............. IC Air Pump 2 ..................... 3 ............. 22-05 ............. IC Pump Feet 3 ..................... 3 .......... ...

  • Hellenbrand Iron Curtain System - page 15

    15 Iron Curtain Aeration Pump Item Part No. No. Description Qty. 1 .......... 74-625646 .............. Screw/Head .................................... 4 2 .......... 74-660631-504 ....... Head ............................................... 1 3 .......... 74-623121 .............. O-Ring/Head .................................. 1 4 .......... 74-6253 ...

  • Hellenbrand Iron Curtain System - page 16

    16 Iron Curtain Aeration Pump Repair Instructions Air pump must be removed from tank and have power supply disconnected before proceeding. 1. Remove four front cover screws and remove front cover and cover gasket. 2. Remove four pump head screws and remove pump head. 3. Remove valve plate assembly. 4. Remove felt air filter on side of pump with a f ...

  • Hellenbrand Iron Curtain System - page 17

    17 IC-10 Series Control V alve Assembly ITEM NO. NO. REQ'D. PART NO. DESCRIPTION 1 ..................... 1 ............. 49-11212NP .. Nickel Valve Body 2 ..................... 1 ............. 49-10757 ....... End Spacer 3 ..................... 6 ............. 49-10545 ....... Seal Ring 4 ..................... 5 ............. 49-11451 ....... ...

  • Hellenbrand Iron Curtain System - page 18

    18 1 IC-12 Series Control V alve Assembly 14 1 2 3 4 5 11 10 9 8 7 6 12 13 15 12 19 20 16 17 18 ITEM NO. NO. REQ'D. PART NO. DESCRIPTION 1 .............. 1 ................... 49-14749-02NP .. Nickel Valve Body 2 .............. 1 ................... 49-10757 ............ End Spacer 3 .............. 6 ................... 49-10545 ............ S ...

  • Hellenbrand Iron Curtain System - page 19

    19 Instructions for Replacing Piston Assembly and Seal Kit Replacing Piston Assembly See pages 17 and 18 for Parts Diagrams. 1. Place Iron Curtain System on bypass. (Close inlet and outlet valves and open bypass valve.) See Figures 1, 2 & 3 on page 8. 2. Relieve pressure by manually advancing timer to back- wash position (See page 10). Unplug c ...

  • Hellenbrand Iron Curtain System - page 20

    20 Removing Power Head Removing Seal from Valve Body Piston Back Plate Seal Hook to Remove Seals Seal FIGURE 14 FIGURE 15 8. Using the puller, remove the first spacer. 9. Alternately remove the remaining seals and spacers in accordance with steps #7 and 8. 10. The last or end spacer does not have any holes for the pins of the puller to engage, ther ...

  • Hellenbrand Iron Curtain System - page 21

    21 Removing Spacer from Valve Body Replacing Spacer in Valve Body Placing Seal in Brass Sleeve of Stuffer Removing Stuffer from Valve Body after Inserting Seal Puller to Remove Spacers Stuffer to Replace Spacers and Seals Spacer Stuffer Seal FIGURE 18 FIGURE 19 FIGURE 16 FIGURE 17 24. Open inlet valve no more than 1/4 turn and allow system to fill ...

  • Hellenbrand Iron Curtain System - page 22

    22 IRON CURT AIN FLOW DIAGRAMS Step 1. Service Position Raw water enters the aeration- tank inlet, flows thru the inlet diffuser, thru a head of air, down thru the aeration tank, thru the pick-up tube, out the aeration head, into the filter control inlet, and down thru the multi-media bed. Filtered water is collected by the bottom distributor, flow ...

  • Hellenbrand Iron Curtain System - page 23

    23 Step 3. Bleeding Off the Aeration System The Iron Curtain Control Center automatically shifts the controller into the Aeration recharge cycle. The air bleedoff valve opens up and allows raw water and/or air to pass thru the bleed off tube in the aeration tank to the drain. The air recharge valve is also open during this time; however, a check va ...

  • Hellenbrand Iron Curtain System - page 24

    24 Step 5. Bleeding Off Excess Air The Iron Curtain Control Center automatically turns the air com- pressor pump off and allows both valves to remain open. The air bleedoff valve will bleed off any excess air which was pumped in during the previous step and the check valve in the recharge line prevents any backflow into the air compressor system. U ...

  • Hellenbrand Iron Curtain System - page 25

    25 1a. Clean or replace drain line flow control 2a. Check for minimum specified flow and pressure requirements of filter system 3a. (Generally will only plug with the presence of iron bacteria) Clean aeration assembly and shock treat the water supply with chlorine as needed to control iron bacteria 4a. Rebed filter and correct the cause of fouling ...

  • Hellenbrand Iron Curtain System - page 26

    26 Complaint Problem Cause Solution A. Dirt lodged under seat of valve B. Faulty or defective relief valve A. This can be expected when water is aerated under pressure A. See complaint #1 problem A & B A. Inlet check valve not sealing A. Reduced pressure in distribution system A. New filter backwashed during first 24 hours after installation B. ...

  • Hellenbrand Iron Curtain System - page 27

    27 Winterizing Iron Curtain Systems (Optional) In certain climates where houses and/or cottages are not heated during the winter months, Iron Curtain Systems must have the water removed from them to protect from damage due to freezing. Following are instructions for “winterizing” Iron Curtain Systems. Prior to draining water distributor system ...

  • Hellenbrand Iron Curtain System - page 28

    28 73-510 7/03-2500 IRON CURT AIN FIL TER SYSTEMS LIMITED W ARRANTY Hellenbrand, Inc., warrants to the original consumer/purchaser against defects in material and/or workmanship from the date of the original installation as follows: For a Period of FIVE YEARS: The 3/4” or 1” control valve(s) including electrical parts, internal parts, and valve ...

Fabricant Hellenbrand Catégorie Water Dispenser

Les documents que nous recevons du fabricant de l'appareilHellenbrand Iron Curtain System peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Hellenbrand
- manuels d’utilisations Iron Curtain System
- fiches produit Hellenbrand
- dépliants
- ou étiquettes-énergie Hellenbrand Iron Curtain System
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Hellenbrand Iron Curtain System.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Hellenbrand Iron Curtain System, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Hellenbrand Iron Curtain System. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Hellenbrand Iron Curtain System.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Hellenbrand Iron Curtain System, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Hellenbrand Iron Curtain System par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Hellenbrand Iron Curtain System.

Le manuel d’utilisation complet Hellenbrand, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Hellenbrand Iron Curtain System - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Hellenbrand Iron Curtain System, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lHellenbrand Iron Curtain System qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Hellenbrand Iron Curtain System - qui devraient nous aider dans les premières étapes lors de l'utilisation Hellenbrand Iron Curtain System
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Hellenbrand Iron Curtain System
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Hellenbrand Iron Curtain System dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Hellenbrand Iron Curtain System?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Hellenbrand Iron Curtain System, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Hellenbrand Iron Curtain System il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)