Italiano dropdown-ico

Manuale per l’uso Hellenbrand Iron Curtain System

28 pagine 0.56 mb
Scarica

Vai alla pagina of 28

Summary
  • Hellenbrand Iron Curtain System - page 1

    For systems manufactured after October 1997 Manufactured by: HELLENBRAND, INC. 404 Moravian Valley Road • PO Box 187 Waunakee, Wisconsin 53597 Phone: 608-849-3050 • Fax: 608-849-7398 Web: www.hellenbrand.com • Email: info@hellenbrand.com Owner ’ s Manual ©2003 TM TM ...

  • Hellenbrand Iron Curtain System - page 2

    2 Congratulations on your purchase of one of the finest water treatment systems available today – the Iron Curtain System. This patented, non-chemical filter system, when properly applied will remove iron, manganese and/or hydrogen sulfide from your water supply. The Iron Curtain has been third-party tested by the Water Quality Association. An op ...

  • Hellenbrand Iron Curtain System - page 3

    3 INST ALLA TION DA T A Date of Installation _______________________________________ Model No.___________________________________ Address of Installation ___________________________________________________________________________________ Installed By_____________________________________________________________________________________________ Raw Wa ...

  • Hellenbrand Iron Curtain System - page 4

    4 IRON CUR T AIN the way to solve this problem is to use layers of media.” The advantages of a multi-media bed are: 1. Longer runs between backwash times. 2. Caking of the bed and breakthrough of turbidity are virtually eliminated. 3. Much higher service flow rates per square foot. 4. Higher degree of clarity because of the heavier, finer filter ...

  • Hellenbrand Iron Curtain System - page 5

    5 Operating Conditions The Iron Curtain System has been validated by the WQA under their S-200 Filter Standard for the reduction/removal of iron, manganese, and/or hydrogen sulfide. The concentration limits listed below reflect the maximum individual limit that each contaminant was tested for separately without any interference of other contaminant ...

  • Hellenbrand Iron Curtain System - page 6

    6 Caution: The water pressure is not to exceed 70 p.s.i.; water temperature is not to exceed 110 ° F; conditioner cannot be subject to freezing conditions; conditioner cannot be subject to a negative pressure or vacuum. On installations where there is the possibility of a negative pressure or vacuum, a vacuum breaker or check valve must be install ...

  • Hellenbrand Iron Curtain System - page 7

    7 Instructions for Adding IC pH Correction Media See Figures 1, 2 & 3 on page 8.. 1. Place Iron Curtain System on bypass. (Close inlet and outlet valves and open bypass valve.) 2. Relieve pressure by manually advancing timer to back- wash position (see page 10). Unplug control valve after valve is shifted into backwash position and piston has s ...

  • Hellenbrand Iron Curtain System - page 8

    8 Due to existing plumbing conditions, you may want to choose an alternate installation configuration. Refer to Figures 2 and 3 below for alternate installation diagrams. FIGURE 1 Carefully place a pry bar (long screwdriver, wrench, etc.) between the screws and apply pressure clockwise until tight. Be careful not to crease or tear the o-rings in th ...

  • Hellenbrand Iron Curtain System - page 9

    9 How T o Set T imer 1 How to set days on which water conditioner is to regenerate. Rotate the skipper wheel until the number "1" is at the red pointer. Set the days that regeneration is to occur by sliding tabs on the skipper wheel outward to expose trip fingers. Each tab is one day. Tab at red pointer is tonight. Moving clockwise from t ...

  • Hellenbrand Iron Curtain System - page 10

    10 How T o Manually Regenerate Y our W ater F ilter At Any T ime Slowly turn the manual regeneration knob clockwise until the drive motor starts running. The movement of the manual regeneration knob engages the program wheel and starts the regeneration program. The black center knob will make one revolution in approximately the following three hour ...

  • Hellenbrand Iron Curtain System - page 11

    11 How T o Set Regeneration Cycle Program 1 How to set the regeneration cycle program. The regeneration cycle program on your Iron Curtain Filter has been factory preset, however, portions of the cycle or program may be lengthened or shortened to suit local conditions. To expose cycle program wheel, grasp timer in upper left- hand corner and pull, ...

  • Hellenbrand Iron Curtain System - page 12

    12 Iron Curtain System Iron Curtain Wiring Diagram 1 2 3 WHITE BLK/WHT GREEN GREEN BLACK WH WHITE BLK/WHT BROWN YELLOW RED BLACK WHITE BLK/WHT BROWN YELLOW RED BLACK BLACK BLACK BLACK BLACK/WHITE TIMER MOTOR PROGRAM ACTUATOR SWITCH AIR PUMP SWITCH BLACK BLACK BLACK PROGRAM SWITCH HOMING SWITCH VALVE DRIVE MOTOR HOMING SWITCH TO AIR PUMP (Located be ...

  • Hellenbrand Iron Curtain System - page 13

    13 Iron Curtain T imer Assembly ITEM NO. NO. REQ'D. PART NO. DESCRIPTION 1 ..................... 1 ............. 49-13870 ....... Timer Housing 2 ..................... 1 ............. 49-13011 ....... Cycle Actuator Arm 3 ..................... 1 ............. 49-49-60519 .. 24 Hour Gear 4 ..................... 1 ............. 49-13959 ....... ...

  • Hellenbrand Iron Curtain System - page 14

    14 Iron Curtain Control Drive Assembly 32 10 7 9 11 12 8 4 13 14 1 2 31 33 17 16 18 19 28 30 29 26 25 24 21 20 27 34 23 15 ITEM NO. NO. REQ'D. PART NO. DESCRIPTION 1 ..................... 1 ............. 22-01 ............. IC Air Pump 2 ..................... 3 ............. 22-05 ............. IC Pump Feet 3 ..................... 3 .......... ...

  • Hellenbrand Iron Curtain System - page 15

    15 Iron Curtain Aeration Pump Item Part No. No. Description Qty. 1 .......... 74-625646 .............. Screw/Head .................................... 4 2 .......... 74-660631-504 ....... Head ............................................... 1 3 .......... 74-623121 .............. O-Ring/Head .................................. 1 4 .......... 74-6253 ...

  • Hellenbrand Iron Curtain System - page 16

    16 Iron Curtain Aeration Pump Repair Instructions Air pump must be removed from tank and have power supply disconnected before proceeding. 1. Remove four front cover screws and remove front cover and cover gasket. 2. Remove four pump head screws and remove pump head. 3. Remove valve plate assembly. 4. Remove felt air filter on side of pump with a f ...

  • Hellenbrand Iron Curtain System - page 17

    17 IC-10 Series Control V alve Assembly ITEM NO. NO. REQ'D. PART NO. DESCRIPTION 1 ..................... 1 ............. 49-11212NP .. Nickel Valve Body 2 ..................... 1 ............. 49-10757 ....... End Spacer 3 ..................... 6 ............. 49-10545 ....... Seal Ring 4 ..................... 5 ............. 49-11451 ....... ...

  • Hellenbrand Iron Curtain System - page 18

    18 1 IC-12 Series Control V alve Assembly 14 1 2 3 4 5 11 10 9 8 7 6 12 13 15 12 19 20 16 17 18 ITEM NO. NO. REQ'D. PART NO. DESCRIPTION 1 .............. 1 ................... 49-14749-02NP .. Nickel Valve Body 2 .............. 1 ................... 49-10757 ............ End Spacer 3 .............. 6 ................... 49-10545 ............ S ...

  • Hellenbrand Iron Curtain System - page 19

    19 Instructions for Replacing Piston Assembly and Seal Kit Replacing Piston Assembly See pages 17 and 18 for Parts Diagrams. 1. Place Iron Curtain System on bypass. (Close inlet and outlet valves and open bypass valve.) See Figures 1, 2 & 3 on page 8. 2. Relieve pressure by manually advancing timer to back- wash position (See page 10). Unplug c ...

  • Hellenbrand Iron Curtain System - page 20

    20 Removing Power Head Removing Seal from Valve Body Piston Back Plate Seal Hook to Remove Seals Seal FIGURE 14 FIGURE 15 8. Using the puller, remove the first spacer. 9. Alternately remove the remaining seals and spacers in accordance with steps #7 and 8. 10. The last or end spacer does not have any holes for the pins of the puller to engage, ther ...

  • Hellenbrand Iron Curtain System - page 21

    21 Removing Spacer from Valve Body Replacing Spacer in Valve Body Placing Seal in Brass Sleeve of Stuffer Removing Stuffer from Valve Body after Inserting Seal Puller to Remove Spacers Stuffer to Replace Spacers and Seals Spacer Stuffer Seal FIGURE 18 FIGURE 19 FIGURE 16 FIGURE 17 24. Open inlet valve no more than 1/4 turn and allow system to fill ...

  • Hellenbrand Iron Curtain System - page 22

    22 IRON CURT AIN FLOW DIAGRAMS Step 1. Service Position Raw water enters the aeration- tank inlet, flows thru the inlet diffuser, thru a head of air, down thru the aeration tank, thru the pick-up tube, out the aeration head, into the filter control inlet, and down thru the multi-media bed. Filtered water is collected by the bottom distributor, flow ...

  • Hellenbrand Iron Curtain System - page 23

    23 Step 3. Bleeding Off the Aeration System The Iron Curtain Control Center automatically shifts the controller into the Aeration recharge cycle. The air bleedoff valve opens up and allows raw water and/or air to pass thru the bleed off tube in the aeration tank to the drain. The air recharge valve is also open during this time; however, a check va ...

  • Hellenbrand Iron Curtain System - page 24

    24 Step 5. Bleeding Off Excess Air The Iron Curtain Control Center automatically turns the air com- pressor pump off and allows both valves to remain open. The air bleedoff valve will bleed off any excess air which was pumped in during the previous step and the check valve in the recharge line prevents any backflow into the air compressor system. U ...

  • Hellenbrand Iron Curtain System - page 25

    25 1a. Clean or replace drain line flow control 2a. Check for minimum specified flow and pressure requirements of filter system 3a. (Generally will only plug with the presence of iron bacteria) Clean aeration assembly and shock treat the water supply with chlorine as needed to control iron bacteria 4a. Rebed filter and correct the cause of fouling ...

  • Hellenbrand Iron Curtain System - page 26

    26 Complaint Problem Cause Solution A. Dirt lodged under seat of valve B. Faulty or defective relief valve A. This can be expected when water is aerated under pressure A. See complaint #1 problem A & B A. Inlet check valve not sealing A. Reduced pressure in distribution system A. New filter backwashed during first 24 hours after installation B. ...

  • Hellenbrand Iron Curtain System - page 27

    27 Winterizing Iron Curtain Systems (Optional) In certain climates where houses and/or cottages are not heated during the winter months, Iron Curtain Systems must have the water removed from them to protect from damage due to freezing. Following are instructions for “winterizing” Iron Curtain Systems. Prior to draining water distributor system ...

  • Hellenbrand Iron Curtain System - page 28

    28 73-510 7/03-2500 IRON CURT AIN FIL TER SYSTEMS LIMITED W ARRANTY Hellenbrand, Inc., warrants to the original consumer/purchaser against defects in material and/or workmanship from the date of the original installation as follows: For a Period of FIVE YEARS: The 3/4” or 1” control valve(s) including electrical parts, internal parts, and valve ...

Fabbricante Hellenbrand Categoria Water Dispenser

I documenti che otteniamo dal fabbricante del dispositivoHellenbrand Iron Curtain System possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Hellenbrand
- manuali per l’uso Iron Curtain System
- schede prodotto Hellenbrand
- opuscoli
- o etichette energetiche Hellenbrand Iron Curtain System
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Hellenbrand Iron Curtain System.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Hellenbrand Iron Curtain System, manuali di manutenzione, brevi manuali o manuali utente Hellenbrand Iron Curtain System. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Hellenbrand Iron Curtain System.

Manuali per l’uso simili

Manuale completo del dispositivo Hellenbrand Iron Curtain System, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Hellenbrand Iron Curtain System dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Hellenbrand Iron Curtain System.

Il manuale per l’uso completo Hellenbrand, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Hellenbrand Iron Curtain System - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Hellenbrand Iron Curtain System, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Hellenbrand Iron Curtain System che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Hellenbrand Iron Curtain System - che ci dovrebbe aiutare nei primi passi durante l'uso Hellenbrand Iron Curtain System
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Hellenbrand Iron Curtain System
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Hellenbrand Iron Curtain System in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Hellenbrand Iron Curtain System?

Utilizza il modulo sottostante

Se non hai risolto il problema con Hellenbrand Iron Curtain System con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Hellenbrand Iron Curtain System è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)