Français dropdown-ico

Manuel d’utilisation Yard Machines 570

24 pages 0.9 mb
Télécharger

Aller à la page of 24

Summary
  • Yard Machines 570 - page 1

    IMPOR TANT: READ SAFETY RULES AND INSTRUCTIONS CAREFUL LY MTD PRODUCTS INC. P .O. B OX 368022 CLEVELAND, OHIO 44136-9722 20” Side Discharge High Wheel Mower 570 Series PRINTED IN U.S.A. FORM NO. 770-1044A O PER AT OR’S M AN UAL Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved for ...

  • Yard Machines 570 - page 2

    2 Content Page Safe Operation Practices ......................................................................... 3 Slope Guage ............................................................................................ 5 Finding Model Number ............................................................................. 6 Unpacking ................ ...

  • Yard Machines 570 - page 3

    3 1. GENERAL OPERATION • Read this owner’s guide carefully in its entirety before attempting to assemble this machine. Read, understand, and follow all instructions on the machine and in the manual(s) before operation. Be completely familiar with the controls and the proper use of this machine before operating it. Keep this manual in a safe pla ...

  • Yard Machines 570 - page 4

    4 DO: • Mow across the face of slopes; never up and down. Exercise extreme caution when changing direction on slopes. • Watch for holes, ruts, hidden objects, or bumps. Tall grass can hide obstacles. • Always be sure of your footing. A slip and fall can cause serious personal injury. If you feel you are losing your balance release the blade c ...

  • Yard Machines 570 - page 5

    5 SECTION 2: SLOPE GAUGE Use this page as a guide to determine slopes where you may not operate safely. 15o SIGHT AND HOL D THIS LEVEL W ITH A VERTICAL T REE A POWE R POLE A CORNER OF A BUILDING OR A FENC E POST F O L D O N D O T T E D L I N E , R E P R E S E N T I N G A 1 5 o S L O P E WARNING Do not mow on inclines with a slope in excess o f 15 d ...

  • Yard Machines 570 - page 6

    6 SECTION 3: FINDING MODEL NUMBER This owner’s guide is an important part of your new Yard-Machine lawn mower. It will help you to assemble, prepare and maintain your mower. Please read and understand what it says. Before you start assembling the mower for its first use, please locate its model plate and copy the information on to this owner’s ...

  • Yard Machines 570 - page 7

    7 SECTION 5: HARDWARE PACK Please identify each piece of hardware in the hardware pack with the following illustrated list. This illustrated list is divided into sections according to the mower assembly procedure. For convenience in assembly, sort out the hardware according to the sections given here. NOTE: The actual number of hardware pieces nece ...

  • Yard Machines 570 - page 8

    8 SECTION 6: SETTING UP MOWER Tools Required • Pair of Pliers • Funnel • Set of adjustable wrenches Disconnecting Spark Plug • Before setting up your lawn mower, disconnect the spark plug wire from the spark plug, and ground it against the engine. If the engine is equipped with the optional rubber boot, attach the boot to a bolt on the engi ...

  • Yard Machines 570 - page 9

    9 Attaching Upper Handle • Place the upper handle in position over the lower handle aligning the lowest hole on the upper handle with the top hole on the lower handle. Make sure that the blade control handle is at the top. • Insert carriage bolt through the upper handle as shown in Figure 4 and secure with a hex nut and lock washer. • Secure ...

  • Yard Machines 570 - page 10

    10 FIGURE 6 • Secure the cable to the lower left handle near the base of the unit with a cable tie. Insert the cable tie through the second hole on the left handle bracket and wrap around the lower handle making sure to keep the cable inside this ring. Pull the cable tie and trim off extra. See Figure 7. FIGURE 7 Attaching Blade Control Handle Re ...

  • Yard Machines 570 - page 11

    11 Attaching Starter Rope • The rope guide and associated hardware are included in the hardware pack. Insert the open end of the rope guide into the middle hole in the right upper handle. See Figure 9. • Loosely attach the rope guide to the upper handle with a lock nut. Do not tighten at this time. • Locate the starter rope on the recoil star ...

  • Yard Machines 570 - page 12

    12 Attaching Wheels The three holes on each side of the front and rear of the cutting deck provide three adjustable cutting height positions for the mower. Attach all four wheels at the same relative position for an even cut. Attaching front wheel You will find the wheels among the loose parts and the necessary hardware in the hardware pack. • Bl ...

  • Yard Machines 570 - page 13

    13 • Insert axle bolt with washers through wheel assembly. See Figure 12 inset. • Place the small bell washer on the other end of the axle bolt with the crown side towards the wheel. • Slide the wheel assembly with all the hardware through one of the three holes on the handle bracket. See Figure 12. Remember to insert the axle bolt and the wh ...

  • Yard Machines 570 - page 14

    14 SECTION 8: OPERATION Gas And Oil Fill-Up Oil: • Only use high quality detergent oil rated with API service classification SF, SG or SH. Use SAE30 oil; do not use 10W40 oil. • Position the mower on level ground and clean area around oil fill plug. • Remove oil fill plug.See Figure 14. Pour recommended oil through the oil fill till full. • ...

  • Yard Machines 570 - page 15

    15 • To prevent the unit from sliding, place your foot firmly against the tire. • Move throttle control all the way forward. This step is not applicable in case of mowers with fixed throttle. • Push primer three times. Wait about two seconds between each push. In cold weather around 55 o F or below, prime five times. Do not prime to restart a ...

  • Yard Machines 570 - page 16

    16 • Tip the mower so that it rests on the housing. Keep the side with the air cleaner facing up. Hold the mower firmly. • Scrape and clean the underside of the deck with a suitable tool. • Put the mower back on its wheels on the ground. If you had put plastic under the gas cap, make sure to remove it now. WARNING: Never tip the mower more th ...

  • Yard Machines 570 - page 17

    17 To Remove Blade • Remove the bolt and blade bell support which hold the blade and adapter to the engine crankshaft. See Figure 15A. • Remove the blade and adapter from the crankshaft. To Replace Blade: • Before reinstalling the blade and the blade adapter to the unit, lubricate the engine crankshaft and the inner surface of the blade adapt ...

  • Yard Machines 570 - page 18

    18 NOTE: Make sure not to lose any hardware while reassembling the wheels. • Adjust all four wheel positions up or down by removing the wheels from the deck and reattaching to the hole above or below. See Figure 16. Remember to attach all four wheels at the same relative position. FIGURE 16 Adjusting Carburetor If the engine is running rough, min ...

  • Yard Machines 570 - page 19

    19 SECTION 11: TROUBLE-SHOOTING GUIDE PROBLEM POSSIBLE C AUSE CORRECTIVE ACTION Engine fails to start 1. Blade control handle disengaged 2. Spark plug wire disconnected 3. Throttle control lever not in starting position 4. Fuel tank empty, or stale fuel 5. Blocked fuel line 6. Faulty spark plug 7. Engine flooded 1. Engage blade control handle 2. Co ...

  • Yard Machines 570 - page 20

    20 Your Notes Date Comment ...

  • Yard Machines 570 - page 21

    21 SECTION 12: SHROUD CHART Pa rt No. 751B281439 751B281440 751B281443 Color Dark Red Black Bright Red Pa rt N o. 731-1395A 731-1396A 731-1397A Color Red Black Gray Pa rt N o. 731-1587A 731-1603A 731-1610A 731-1620A Color Black Y ellow Pewter Gray Pa rt N o. 731-1561 Color Black Hardware: 710-1256 (Screw) Hardware: 710-1256 (Screw) Hardware: 710-11 ...

  • Yard Machines 570 - page 22

    22 SECTION 13: REPAIR PARTS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 19 20 21 22 23 24 16 26 27 17 16 18 30 31 31 28 33 34 23 25 7 8 9 6 37 35 38 19 11 16 30 18 35 37 27 17 30 24 16 30 6 5 ...

  • Yard Machines 570 - page 23

    23 Ref. No. Pa rt N o. Code Description 1 747-0976 Control Handle Assembly 2 749-1076 Upper Handle 3 746-0946 Control Cable: 48.25” 4 710-0262 Carriage Screw 5/16-18 x 1.5” 5 710-0726 Self-Tapping Screw 5/16- 12 6 734-1864 734-1976 N Rear Wheel 14” x 1.8 Bar Rear Wheel 14” x 1.8 7 738-0481 Rear Axle Bolt 8 736-0182 Spring Washer 9 736-0456 ...

  • Yard Machines 570 - page 24

    MANU FA CTURER’S LIMITED WARRANTY FOR: For TWO YEARS from the date of retail purchase within the United States of America, its possessions and territories, MTD PRODUCTS INC will, at its option, repair or replace, for the original purchaser, free of charge, any part or parts found to be defective in material or workmanship. This warranty covers un ...

Fabricant Yard Machines Catégorie Lawn Mower

Les documents que nous recevons du fabricant de l'appareilYard Machines 570 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Yard Machines
- manuels d’utilisations 570
- fiches produit Yard Machines
- dépliants
- ou étiquettes-énergie Yard Machines 570
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Yard Machines 570.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Yard Machines 570, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Yard Machines 570. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Yard Machines 570.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Yard Machines 570, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Yard Machines 570 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Yard Machines 570.

Le manuel d’utilisation complet Yard Machines, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Yard Machines 570 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Yard Machines 570, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lYard Machines 570 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Yard Machines 570 - qui devraient nous aider dans les premières étapes lors de l'utilisation Yard Machines 570
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Yard Machines 570
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Yard Machines 570 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Yard Machines 570?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Yard Machines 570, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Yard Machines 570 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)