English dropdown-ico

Manual Yard Machines 570

24 pages 0.9 mb
Download

Go to site of 24

Summary
  • Yard Machines 570 - page 1

    IMPOR TANT: READ SAFETY RULES AND INSTRUCTIONS CAREFUL LY MTD PRODUCTS INC. P .O. B OX 368022 CLEVELAND, OHIO 44136-9722 20” Side Discharge High Wheel Mower 570 Series PRINTED IN U.S.A. FORM NO. 770-1044A O PER AT OR’S M AN UAL Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved for ...

  • Yard Machines 570 - page 2

    2 Content Page Safe Operation Practices ......................................................................... 3 Slope Guage ............................................................................................ 5 Finding Model Number ............................................................................. 6 Unpacking ................ ...

  • Yard Machines 570 - page 3

    3 1. GENERAL OPERATION • Read this owner’s guide carefully in its entirety before attempting to assemble this machine. Read, understand, and follow all instructions on the machine and in the manual(s) before operation. Be completely familiar with the controls and the proper use of this machine before operating it. Keep this manual in a safe pla ...

  • Yard Machines 570 - page 4

    4 DO: • Mow across the face of slopes; never up and down. Exercise extreme caution when changing direction on slopes. • Watch for holes, ruts, hidden objects, or bumps. Tall grass can hide obstacles. • Always be sure of your footing. A slip and fall can cause serious personal injury. If you feel you are losing your balance release the blade c ...

  • Yard Machines 570 - page 5

    5 SECTION 2: SLOPE GAUGE Use this page as a guide to determine slopes where you may not operate safely. 15o SIGHT AND HOL D THIS LEVEL W ITH A VERTICAL T REE A POWE R POLE A CORNER OF A BUILDING OR A FENC E POST F O L D O N D O T T E D L I N E , R E P R E S E N T I N G A 1 5 o S L O P E WARNING Do not mow on inclines with a slope in excess o f 15 d ...

  • Yard Machines 570 - page 6

    6 SECTION 3: FINDING MODEL NUMBER This owner’s guide is an important part of your new Yard-Machine lawn mower. It will help you to assemble, prepare and maintain your mower. Please read and understand what it says. Before you start assembling the mower for its first use, please locate its model plate and copy the information on to this owner’s ...

  • Yard Machines 570 - page 7

    7 SECTION 5: HARDWARE PACK Please identify each piece of hardware in the hardware pack with the following illustrated list. This illustrated list is divided into sections according to the mower assembly procedure. For convenience in assembly, sort out the hardware according to the sections given here. NOTE: The actual number of hardware pieces nece ...

  • Yard Machines 570 - page 8

    8 SECTION 6: SETTING UP MOWER Tools Required • Pair of Pliers • Funnel • Set of adjustable wrenches Disconnecting Spark Plug • Before setting up your lawn mower, disconnect the spark plug wire from the spark plug, and ground it against the engine. If the engine is equipped with the optional rubber boot, attach the boot to a bolt on the engi ...

  • Yard Machines 570 - page 9

    9 Attaching Upper Handle • Place the upper handle in position over the lower handle aligning the lowest hole on the upper handle with the top hole on the lower handle. Make sure that the blade control handle is at the top. • Insert carriage bolt through the upper handle as shown in Figure 4 and secure with a hex nut and lock washer. • Secure ...

  • Yard Machines 570 - page 10

    10 FIGURE 6 • Secure the cable to the lower left handle near the base of the unit with a cable tie. Insert the cable tie through the second hole on the left handle bracket and wrap around the lower handle making sure to keep the cable inside this ring. Pull the cable tie and trim off extra. See Figure 7. FIGURE 7 Attaching Blade Control Handle Re ...

  • Yard Machines 570 - page 11

    11 Attaching Starter Rope • The rope guide and associated hardware are included in the hardware pack. Insert the open end of the rope guide into the middle hole in the right upper handle. See Figure 9. • Loosely attach the rope guide to the upper handle with a lock nut. Do not tighten at this time. • Locate the starter rope on the recoil star ...

  • Yard Machines 570 - page 12

    12 Attaching Wheels The three holes on each side of the front and rear of the cutting deck provide three adjustable cutting height positions for the mower. Attach all four wheels at the same relative position for an even cut. Attaching front wheel You will find the wheels among the loose parts and the necessary hardware in the hardware pack. • Bl ...

  • Yard Machines 570 - page 13

    13 • Insert axle bolt with washers through wheel assembly. See Figure 12 inset. • Place the small bell washer on the other end of the axle bolt with the crown side towards the wheel. • Slide the wheel assembly with all the hardware through one of the three holes on the handle bracket. See Figure 12. Remember to insert the axle bolt and the wh ...

  • Yard Machines 570 - page 14

    14 SECTION 8: OPERATION Gas And Oil Fill-Up Oil: • Only use high quality detergent oil rated with API service classification SF, SG or SH. Use SAE30 oil; do not use 10W40 oil. • Position the mower on level ground and clean area around oil fill plug. • Remove oil fill plug.See Figure 14. Pour recommended oil through the oil fill till full. • ...

  • Yard Machines 570 - page 15

    15 • To prevent the unit from sliding, place your foot firmly against the tire. • Move throttle control all the way forward. This step is not applicable in case of mowers with fixed throttle. • Push primer three times. Wait about two seconds between each push. In cold weather around 55 o F or below, prime five times. Do not prime to restart a ...

  • Yard Machines 570 - page 16

    16 • Tip the mower so that it rests on the housing. Keep the side with the air cleaner facing up. Hold the mower firmly. • Scrape and clean the underside of the deck with a suitable tool. • Put the mower back on its wheels on the ground. If you had put plastic under the gas cap, make sure to remove it now. WARNING: Never tip the mower more th ...

  • Yard Machines 570 - page 17

    17 To Remove Blade • Remove the bolt and blade bell support which hold the blade and adapter to the engine crankshaft. See Figure 15A. • Remove the blade and adapter from the crankshaft. To Replace Blade: • Before reinstalling the blade and the blade adapter to the unit, lubricate the engine crankshaft and the inner surface of the blade adapt ...

  • Yard Machines 570 - page 18

    18 NOTE: Make sure not to lose any hardware while reassembling the wheels. • Adjust all four wheel positions up or down by removing the wheels from the deck and reattaching to the hole above or below. See Figure 16. Remember to attach all four wheels at the same relative position. FIGURE 16 Adjusting Carburetor If the engine is running rough, min ...

  • Yard Machines 570 - page 19

    19 SECTION 11: TROUBLE-SHOOTING GUIDE PROBLEM POSSIBLE C AUSE CORRECTIVE ACTION Engine fails to start 1. Blade control handle disengaged 2. Spark plug wire disconnected 3. Throttle control lever not in starting position 4. Fuel tank empty, or stale fuel 5. Blocked fuel line 6. Faulty spark plug 7. Engine flooded 1. Engage blade control handle 2. Co ...

  • Yard Machines 570 - page 20

    20 Your Notes Date Comment ...

  • Yard Machines 570 - page 21

    21 SECTION 12: SHROUD CHART Pa rt No. 751B281439 751B281440 751B281443 Color Dark Red Black Bright Red Pa rt N o. 731-1395A 731-1396A 731-1397A Color Red Black Gray Pa rt N o. 731-1587A 731-1603A 731-1610A 731-1620A Color Black Y ellow Pewter Gray Pa rt N o. 731-1561 Color Black Hardware: 710-1256 (Screw) Hardware: 710-1256 (Screw) Hardware: 710-11 ...

  • Yard Machines 570 - page 22

    22 SECTION 13: REPAIR PARTS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 19 20 21 22 23 24 16 26 27 17 16 18 30 31 31 28 33 34 23 25 7 8 9 6 37 35 38 19 11 16 30 18 35 37 27 17 30 24 16 30 6 5 ...

  • Yard Machines 570 - page 23

    23 Ref. No. Pa rt N o. Code Description 1 747-0976 Control Handle Assembly 2 749-1076 Upper Handle 3 746-0946 Control Cable: 48.25” 4 710-0262 Carriage Screw 5/16-18 x 1.5” 5 710-0726 Self-Tapping Screw 5/16- 12 6 734-1864 734-1976 N Rear Wheel 14” x 1.8 Bar Rear Wheel 14” x 1.8 7 738-0481 Rear Axle Bolt 8 736-0182 Spring Washer 9 736-0456 ...

  • Yard Machines 570 - page 24

    MANU FA CTURER’S LIMITED WARRANTY FOR: For TWO YEARS from the date of retail purchase within the United States of America, its possessions and territories, MTD PRODUCTS INC will, at its option, repair or replace, for the original purchaser, free of charge, any part or parts found to be defective in material or workmanship. This warranty covers un ...

Manufacturer Yard Machines Category Lawn Mower

Documents that we receive from a manufacturer of a Yard Machines 570 can be divided into several groups. They are, among others:
- Yard Machines technical drawings
- 570 manuals
- Yard Machines product data sheets
- information booklets
- or energy labels Yard Machines 570
All of them are important, but the most important information from the point of view of use of the device are in the user manual Yard Machines 570.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Yard Machines 570, service manual, brief instructions and user manuals Yard Machines 570. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Yard Machines 570.

Similar manuals

A complete manual for the device Yard Machines 570, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Yard Machines 570 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Yard Machines 570.

A complete Yard Machines manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Yard Machines 570 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Yard Machines 570, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Yard Machines 570, that we can find in the current document
3. Tips how to use the basic functions of the device Yard Machines 570 - which should help us in our first steps of using Yard Machines 570
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Yard Machines 570
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Yard Machines 570 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Yard Machines 570?

Use the form below

If you did not solve your problem by using a manual Yard Machines 570, ask a question using the form below. If a user had a similar problem with Yard Machines 570 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)