Manuel d’utilisation American Standard 7038.400

12 pages 1.37 mb
Télécharger

Aller à la page of 12

Summary
  • American Standard 7038.400 - page 1

    3 5 4 4 Cer tified to comply with ANSI A112.18.1 Installation Instructions Bidet Faucet and T ransfer V alve with Ev erClean™ Finish & SpeedC onnec t™ Drain Congr atulations on purchasing your A merican Standard faucet with E verClean finish and Speed Connect drain, two features f ound only on American Standard faucets. *Y our new American ...

  • American Standard 7038.400 - page 2

    M968893 POP-UP DRAIN Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 3 5 4 2 TIGHTEN LOCKNUT 1 REMOVE FLANGE Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B. Remove ...

  • American Standard 7038.400 - page 3

    Connect HOT water supply to inlet of left SHANK and COLD water supply to right SHANK using sealant, appropriate connectors, and COUPLING NUTS. Connect 1-1/4” O.D. tailpiece on POP-UP DRAIN to waste outlet. 10 Connect water supply to V AL VE BODIES (7,7a) with 1/2" IPS FLEXIBLE SUPPLIES (8) or 3/8" O.D. BULL-NOSE RISERS (9) . Use adjusta ...

  • American Standard 7038.400 - page 4

    CHECK DRAIN CONNECTIONS 12 13 TEST INST ALLED FITTING With HANDLES (1) in OFF position, turn on W A TER SUPPLIES (2) and check all connections for leaks. Operate both HANDLES (1) to flush water lines thoroughly . Rotate TRANSFER V AL VE (5) from rim wash to spray several times to check operation. Pull up POP-UP KNOB (3) and fill Bidet with water . ...

  • American Standard 7038.400 - page 5

    M968893 SpeedConnect™ Drain Troubleshooting Guide Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A. Look at the area on the Drain Body where the Cable was attached and locate the component labeled as “Cam” and “Cam Cap” in the illustration. Fig. B. Use fingers or small screwdriver under ei ...

  • American Standard 7038.400 - page 6

    M968893 6 STOPPER INSTALLATION PROCEDURE Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G. To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is fa ...

  • American Standard 7038.400 - page 7

    3 5 4 4 Cer tified to comply with ANSI A112.18.1 Installation Instructions Bidet Faucet and V acuum Br eaker with Ev erClean™ Finish & SpeedC onnec t™ Drain Congr atulations on purchasing your A merican Standard faucet with Ev erClean finish and Speed Connect drain, two featur es found only on American Standard fauc ets. *Y our new American ...

  • American Standard 7038.400 - page 8

    POP-UP DRAIN Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 3 5 4 2 TIGHTEN LOCKNUT 1 REMOVE FLANGE Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B. Remove CLEAR PL ...

  • American Standard 7038.400 - page 9

    Connect HOT water supply to inlet of left SHANK and COLD water supply to right SHANK using sealant, appropriate connectors, and COUPLING NUTS. Connect 1-1/4” O.D. tailpiece on POP-UP DRAIN to waste outlet. 10 Connect water supply to V AL VE BODIES (7,7a) with 1/2" IPS FLEXIBLE SUPPLIES (2) or 3/8" O.D. BULL-NOSE RISERS (3) . Use adjusta ...

  • American Standard 7038.400 - page 10

    CHECK DRAIN CONNECTIONS 12 13 TEST INST ALLED FITTING With HANDLES (1) in OFF position, turn on W A TER SUPPLIES (2) and check all connections for leaks. Operate both HANDLES (1) to flush water lines thoroughly . Rotate TRANSFER V AL VE (5) from rim wash to spray several times to check operation. Pull up POP-UP KNOB (3) and fill Bidet with water . ...

  • American Standard 7038.400 - page 11

    SpeedConnect™ Drain Troubleshooting Guide Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A. Look at the area on the Drain Body where the Cable was attached and locate the component labeled as “Cam” and “Cam Cap” in the illustration. Fig. B. Use fingers or small screwdriver under either sid ...

  • American Standard 7038.400 - page 12

    M968894 6 STOPPER INSTALLATION PROCEDURE Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G. To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is fa ...

Fabricant American Standard Catégorie Indoor Furnishings

Les documents que nous recevons du fabricant de l'appareilAmerican Standard 7038.400 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques American Standard
- manuels d’utilisations 7038.400
- fiches produit American Standard
- dépliants
- ou étiquettes-énergie American Standard 7038.400
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation American Standard 7038.400.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation American Standard 7038.400, manuels d’entretien, brefs manuels ou manuels de l’utilisateur American Standard 7038.400. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit American Standard 7038.400.

Manuel d’utilisation complet de l’appareil American Standard 7038.400, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser American Standard 7038.400 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs American Standard 7038.400.

Le manuel d’utilisation complet American Standard, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel American Standard 7038.400 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières American Standard 7038.400, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lAmerican Standard 7038.400 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil American Standard 7038.400 - qui devraient nous aider dans les premières étapes lors de l'utilisation American Standard 7038.400
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de American Standard 7038.400
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service American Standard 7038.400 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de American Standard 7038.400?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec American Standard 7038.400, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec American Standard 7038.400 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Commentaires (0)