Français dropdown-ico

Manuel d’utilisation Teledyne LLD

25 pages 1.42 mb
Télécharger

Aller à la page of 25

Summary
  • Teledyne LLD - page 1

    Model LLG & LLD Pool and Spa Heater Page 1 SECTION 1. General Information 1A. Introduction This manual provides installation and operation instructions for the Laars Lite, Model LLG and LLD pool and spa heaters. Read these installation and Figure 1. General Configuration. operation instructions completely before proceeding with the installation ...

  • Teledyne LLD - page 2

    Page 2 Gas Association and Canadian Gas Association) as complying with the latest edition of the Standard for Gas-Fired Pool Heaters, ANSI Z21.56, and in Canada with CAN1-4.7-M85. Certain sections of this manual are specific to either United States or Canadian installations, and are labeled as such. 1B. Description The Laars Lite LLD heater gets el ...

  • Teledyne LLD - page 3

    Model LLG & LLD Pool and Spa Heater Page 3 Notes: 1. An Underwriters' Laboratories listed vent cap is required to prevent downdraft and allow the heater to function properly and safely. 2. Use approved roof jack. 2C. Site Location WARNING Improper installation or maintenance can cause nausea or asphyxiation from carbon monoxide in flue gas ...

  • Teledyne LLD - page 4

    Page 4 Figure 4. Non-Combustible Platform. Notes: 1. Blocks must provide solid base and be braced so they cannot slip out of place. 2. Air openings in blocks must be arranged to provide unrestricted opening through entire width or length of base. Figure 3. Outdoor Heater Installation. utility room. In the United States there must be a minimum of 4 ...

  • Teledyne LLD - page 5

    Model LLG & LLD Pool and Spa Heater Page 5 5. Install a sediment trap (drip leg) ahead of the gas controls (see Figure 5). Fit the trap with a threaded cap which can be removed for cleaning. 6. Install a manual gas shutoff valve for service and safety. Do not use a restrictive gas cock. DO NOT USE GAS FLEXIBLE PIPING. 7. Disconnect the heater a ...

  • Teledyne LLD - page 6

    Page 6 use 120 Volt, 60 Hz AC requires rewiring of the heater. This should be done by a certified electrician only, as with all wiring. To wire the heater for 120 Volt, 60 Hz AC, follow the alternate 120V wiring method depicted in Figure 6. Additionally, the ignition control module must be rewired. The wire from the terminal marked IGN/240 must be ...

  • Teledyne LLD - page 7

    Model LLG & LLD Pool and Spa Heater Page 7 Figure 6. LLD Connection/Schematic Wiring Diagram. ...

  • Teledyne LLD - page 8

    Page 8 Figure 7. LLG Connection/Schematic Wiring Diagram be wired for remote operation. The CS-02 remote control permits switching from one temperature controller to the other and turning the heater on and off from a remote location. The CS-04 includes the same features as the CS-02 plus a remote tempera- ture controller. Contact Teledyne Laars for ...

  • Teledyne LLD - page 9

    Model LLG & LLD Pool and Spa Heater Page 9 Figure 8. Field Wiring Connections (LLD). Figure 9. Time Clock Wiring. Figure 10. Piping installation. Figure 11. Plastic piping connections. To connect a 3-wire remote (not supplied by Teledyne Laars), order a wire harness assembly (part No. E0120000) which connects to the flex-temp control panel. Ins ...

  • Teledyne LLD - page 10

    Page 10 Figure 13. Flue collector holddown brackets. Figure 12. Heat exchanger reversal. To install plastic piping (see Figure 11): 1. Remove CPVC nipples from plastic bag. 2. Screw CPVC nipples into metal flange until tight, using teflon tape on plastic threads. 3. Attach PVC plumbing to CPVC pipes using PVC to CPVC cement only. 2G-2. Reversible W ...

  • Teledyne LLD - page 11

    Model LLG & LLD Pool and Spa Heater Page 11 Caution It may be necessary to have help lifting the heat exchanger out and replacing it. 15. Lift out the heat exchanger assembly and set it aside. Re-install heat exchanger 180 degrees from it's original position (header left). 16. When replacing the heat exchanger from the heater, the end baff ...

  • Teledyne LLD - page 12

    Page 12 injector to prevent ozone and air from entering the heater. • When chemical feeders are used, plumb the feeder downstream of the heater and install an inline check valve between the heater and the feeder (a minimum of 18" is required between the heater and the check valve). • Never deposit chemicals directly in the pool skimmer. 2G ...

  • Teledyne LLD - page 13

    Model LLG & LLD Pool and Spa Heater Page 13 Figure 17. Thermometer and pressure relief valve. 3. Turn rotary switch to ON. Heater should start. 4. Pry out the top rubber dirt plug. 5. Use a 7/32 inch (5.55 mm) Allen wrench to turn the adjustment screw very slowly clockwise until the heater goes off (see Figure 18). 6. Slowly turn the pressure s ...

  • Teledyne LLD - page 14

    Page 14 test (see Section 2G-8). 7. Open manual bypass valve until temp rise falls between the min. and max. range. 8. Once the temperature is within the correct range, safety wire handle of the manual bypass valve in place and tag valve to prevent change in the water low. SECTION 3. Operating Instructions 3A. General Information With any new pool ...

  • Teledyne LLD - page 15

    Model LLG & LLD Pool and Spa Heater Page 15 W ARNING: If you do not follow these instructions exactly , a fire or explosion may result, causing property damage, personal injury or loss of life. • If you cannot reach your gas supplier , call the fire department. C. Use only your hand to push in or turn the gas control knob. Never use tools. If ...

  • Teledyne LLD - page 16

    Page 16 FOR YOUR SAFETY READ BEFORE OPERA TING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A . This appliance has a pilot which must be lighted by a push button sparker. When lighting the pilot, follow these instructions exactly. B. BEFORE LIGHTIN ...

  • Teledyne LLD - page 17

    Model LLG & LLD Pool and Spa Heater Page 17 Note: When using metal pipe as heat sink, join metal and PVC/CPVC, using metal male and PVC/CPVC female connection. Figure 20. Typical installation. 3C. Setting the Temperature Control The temperature control (see Figure 17) is calibrated at the factory and covers a range from approximately 70 to 104? ...

  • Teledyne LLD - page 18

    Page 18 3D-3. Spring Start-up To restart the heater in the Spring, have a profes- sional service technician reassemble the heater as follows: 1. Attach the copper tubing to the pressure switch and fill the loop with SAE 50, non-detergent oil (see Figure 21). 2. Tighten the drain plugs. 3. Turn on the main gas supply valve to the heater, outside the ...

  • Teledyne LLD - page 19

    Model LLG & LLD Pool and Spa Heater Page 19 discourage further adjustments. 4. Set the filter time clock to start the pump no earlier than 6:00 AM during the pool heating season. This is the time when nightly heat loss balances. 5. If the pool is only going to be used on weekends, reduce the heater temperature control setting by 8 or 10 degrees ...

  • Teledyne LLD - page 20

    Page 20 4B. Parts List Description Part Number A . VENTING ASSEMBLY 1. Top Enclosure Weldment ................................... R0313201-05 2. Top Filler Plate .................................................... 10535201-05 3. Flue Collector ..................................................... R0316401-05 (R0316406-10 for Canada) 4. Rainshield ...

  • Teledyne LLD - page 21

    Model LLG & LLD Pool and Spa Heater Page 21 Description Part Number 13. Bracket, Insulation Retainer ...................................... 10462200 14. Sleeve, Temperature Control Bulb ............................ 10444900 15. Retainer Bracket ....................................................... 10447300 16 . Wire Harness, High Limit ...... ...

  • Teledyne LLD - page 22

    Page 22 D F E A3 A2 A1 A4 B2 B1 B4 E10 B8 B3 C1 C2 C3 C5 C4 A5 Redundant Limit (LLG only) See Page 23 for detail See Page 23 for detail ...

  • Teledyne LLD - page 23

    Model LLG & LLD Pool and Spa Heater Page 23 Detailed view of LLG Burner Tray Assembly (E) E2 E3 E1 E4, E5, E6, E7, E8, E9 Detailed view of Heat Exchanger Assembly (D) D14, D15, D16, D17 Detailed view of LLD Burner Tray Assembly (E) E2 E3 E1 D13 D18 D10 D19 D12 D11 D20 D1, D3 D5, D6 D2, D4 D8, D9 D7 ...

  • Teledyne LLD - page 24

    Page 24 NOTES ...

  • Teledyne LLD - page 25

    Model LLG & LLD Pool and Spa Heater Page 25 LAARS LITE LIMITED W ARRANTY Y our Laars Lite pool/spa heater is backed by this double warranty to assure your complete satisfaction. 1. Controls, copper heat exchanger tubes, and combustion chamber panels are warranted against defects in materials and workmanship for two (2) years from date of purcha ...

Fabricant Teledyne Catégorie Electric Heater

Les documents que nous recevons du fabricant de l'appareilTeledyne LLD peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Teledyne
- manuels d’utilisations LLD
- fiches produit Teledyne
- dépliants
- ou étiquettes-énergie Teledyne LLD
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Teledyne LLD.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Teledyne LLD, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Teledyne LLD. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Teledyne LLD.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Teledyne LLD, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Teledyne LLD par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Teledyne LLD.

Le manuel d’utilisation complet Teledyne, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Teledyne LLD - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Teledyne LLD, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lTeledyne LLD qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Teledyne LLD - qui devraient nous aider dans les premières étapes lors de l'utilisation Teledyne LLD
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Teledyne LLD
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Teledyne LLD dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Teledyne LLD?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Teledyne LLD, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Teledyne LLD il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)