Teledyne LLDの取扱説明書

25ページ 1.42 mb
ダウンロード

ページに移動 of 25

Summary
  • Teledyne LLD - page 1

    Model LLG & LLD Pool and Spa Heater Page 1 SECTION 1. General Information 1A. Introduction This manual provides installation and operation instructions for the Laars Lite, Model LLG and LLD pool and spa heaters. Read these installation and Figure 1. General Configuration. operation instructions completely before proceeding with the installation ...

  • Teledyne LLD - page 2

    Page 2 Gas Association and Canadian Gas Association) as complying with the latest edition of the Standard for Gas-Fired Pool Heaters, ANSI Z21.56, and in Canada with CAN1-4.7-M85. Certain sections of this manual are specific to either United States or Canadian installations, and are labeled as such. 1B. Description The Laars Lite LLD heater gets el ...

  • Teledyne LLD - page 3

    Model LLG & LLD Pool and Spa Heater Page 3 Notes: 1. An Underwriters' Laboratories listed vent cap is required to prevent downdraft and allow the heater to function properly and safely. 2. Use approved roof jack. 2C. Site Location WARNING Improper installation or maintenance can cause nausea or asphyxiation from carbon monoxide in flue gas ...

  • Teledyne LLD - page 4

    Page 4 Figure 4. Non-Combustible Platform. Notes: 1. Blocks must provide solid base and be braced so they cannot slip out of place. 2. Air openings in blocks must be arranged to provide unrestricted opening through entire width or length of base. Figure 3. Outdoor Heater Installation. utility room. In the United States there must be a minimum of 4 ...

  • Teledyne LLD - page 5

    Model LLG & LLD Pool and Spa Heater Page 5 5. Install a sediment trap (drip leg) ahead of the gas controls (see Figure 5). Fit the trap with a threaded cap which can be removed for cleaning. 6. Install a manual gas shutoff valve for service and safety. Do not use a restrictive gas cock. DO NOT USE GAS FLEXIBLE PIPING. 7. Disconnect the heater a ...

  • Teledyne LLD - page 6

    Page 6 use 120 Volt, 60 Hz AC requires rewiring of the heater. This should be done by a certified electrician only, as with all wiring. To wire the heater for 120 Volt, 60 Hz AC, follow the alternate 120V wiring method depicted in Figure 6. Additionally, the ignition control module must be rewired. The wire from the terminal marked IGN/240 must be ...

  • Teledyne LLD - page 7

    Model LLG & LLD Pool and Spa Heater Page 7 Figure 6. LLD Connection/Schematic Wiring Diagram. ...

  • Teledyne LLD - page 8

    Page 8 Figure 7. LLG Connection/Schematic Wiring Diagram be wired for remote operation. The CS-02 remote control permits switching from one temperature controller to the other and turning the heater on and off from a remote location. The CS-04 includes the same features as the CS-02 plus a remote tempera- ture controller. Contact Teledyne Laars for ...

  • Teledyne LLD - page 9

    Model LLG & LLD Pool and Spa Heater Page 9 Figure 8. Field Wiring Connections (LLD). Figure 9. Time Clock Wiring. Figure 10. Piping installation. Figure 11. Plastic piping connections. To connect a 3-wire remote (not supplied by Teledyne Laars), order a wire harness assembly (part No. E0120000) which connects to the flex-temp control panel. Ins ...

  • Teledyne LLD - page 10

    Page 10 Figure 13. Flue collector holddown brackets. Figure 12. Heat exchanger reversal. To install plastic piping (see Figure 11): 1. Remove CPVC nipples from plastic bag. 2. Screw CPVC nipples into metal flange until tight, using teflon tape on plastic threads. 3. Attach PVC plumbing to CPVC pipes using PVC to CPVC cement only. 2G-2. Reversible W ...

  • Teledyne LLD - page 11

    Model LLG & LLD Pool and Spa Heater Page 11 Caution It may be necessary to have help lifting the heat exchanger out and replacing it. 15. Lift out the heat exchanger assembly and set it aside. Re-install heat exchanger 180 degrees from it's original position (header left). 16. When replacing the heat exchanger from the heater, the end baff ...

  • Teledyne LLD - page 12

    Page 12 injector to prevent ozone and air from entering the heater. • When chemical feeders are used, plumb the feeder downstream of the heater and install an inline check valve between the heater and the feeder (a minimum of 18" is required between the heater and the check valve). • Never deposit chemicals directly in the pool skimmer. 2G ...

  • Teledyne LLD - page 13

    Model LLG & LLD Pool and Spa Heater Page 13 Figure 17. Thermometer and pressure relief valve. 3. Turn rotary switch to ON. Heater should start. 4. Pry out the top rubber dirt plug. 5. Use a 7/32 inch (5.55 mm) Allen wrench to turn the adjustment screw very slowly clockwise until the heater goes off (see Figure 18). 6. Slowly turn the pressure s ...

  • Teledyne LLD - page 14

    Page 14 test (see Section 2G-8). 7. Open manual bypass valve until temp rise falls between the min. and max. range. 8. Once the temperature is within the correct range, safety wire handle of the manual bypass valve in place and tag valve to prevent change in the water low. SECTION 3. Operating Instructions 3A. General Information With any new pool ...

  • Teledyne LLD - page 15

    Model LLG & LLD Pool and Spa Heater Page 15 W ARNING: If you do not follow these instructions exactly , a fire or explosion may result, causing property damage, personal injury or loss of life. • If you cannot reach your gas supplier , call the fire department. C. Use only your hand to push in or turn the gas control knob. Never use tools. If ...

  • Teledyne LLD - page 16

    Page 16 FOR YOUR SAFETY READ BEFORE OPERA TING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A . This appliance has a pilot which must be lighted by a push button sparker. When lighting the pilot, follow these instructions exactly. B. BEFORE LIGHTIN ...

  • Teledyne LLD - page 17

    Model LLG & LLD Pool and Spa Heater Page 17 Note: When using metal pipe as heat sink, join metal and PVC/CPVC, using metal male and PVC/CPVC female connection. Figure 20. Typical installation. 3C. Setting the Temperature Control The temperature control (see Figure 17) is calibrated at the factory and covers a range from approximately 70 to 104? ...

  • Teledyne LLD - page 18

    Page 18 3D-3. Spring Start-up To restart the heater in the Spring, have a profes- sional service technician reassemble the heater as follows: 1. Attach the copper tubing to the pressure switch and fill the loop with SAE 50, non-detergent oil (see Figure 21). 2. Tighten the drain plugs. 3. Turn on the main gas supply valve to the heater, outside the ...

  • Teledyne LLD - page 19

    Model LLG & LLD Pool and Spa Heater Page 19 discourage further adjustments. 4. Set the filter time clock to start the pump no earlier than 6:00 AM during the pool heating season. This is the time when nightly heat loss balances. 5. If the pool is only going to be used on weekends, reduce the heater temperature control setting by 8 or 10 degrees ...

  • Teledyne LLD - page 20

    Page 20 4B. Parts List Description Part Number A . VENTING ASSEMBLY 1. Top Enclosure Weldment ................................... R0313201-05 2. Top Filler Plate .................................................... 10535201-05 3. Flue Collector ..................................................... R0316401-05 (R0316406-10 for Canada) 4. Rainshield ...

  • Teledyne LLD - page 21

    Model LLG & LLD Pool and Spa Heater Page 21 Description Part Number 13. Bracket, Insulation Retainer ...................................... 10462200 14. Sleeve, Temperature Control Bulb ............................ 10444900 15. Retainer Bracket ....................................................... 10447300 16 . Wire Harness, High Limit ...... ...

  • Teledyne LLD - page 22

    Page 22 D F E A3 A2 A1 A4 B2 B1 B4 E10 B8 B3 C1 C2 C3 C5 C4 A5 Redundant Limit (LLG only) See Page 23 for detail See Page 23 for detail ...

  • Teledyne LLD - page 23

    Model LLG & LLD Pool and Spa Heater Page 23 Detailed view of LLG Burner Tray Assembly (E) E2 E3 E1 E4, E5, E6, E7, E8, E9 Detailed view of Heat Exchanger Assembly (D) D14, D15, D16, D17 Detailed view of LLD Burner Tray Assembly (E) E2 E3 E1 D13 D18 D10 D19 D12 D11 D20 D1, D3 D5, D6 D2, D4 D8, D9 D7 ...

  • Teledyne LLD - page 24

    Page 24 NOTES ...

  • Teledyne LLD - page 25

    Model LLG & LLD Pool and Spa Heater Page 25 LAARS LITE LIMITED W ARRANTY Y our Laars Lite pool/spa heater is backed by this double warranty to assure your complete satisfaction. 1. Controls, copper heat exchanger tubes, and combustion chamber panels are warranted against defects in materials and workmanship for two (2) years from date of purcha ...

メーカー Teledyne カテゴリー Electric Heater

Teledyne LLDのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- LLDの取扱説明書
- Teledyneの製品カード
- パンフレット
- またはTeledyne LLDの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Teledyne LLDの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Teledyne LLDの取り付け説明書、サービスマニュアル、簡易説明書、またはTeledyne LLDのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Teledyne LLDの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Teledyne LLDデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがTeledyne LLDを使用するのを助ける技術的文書のことです。説明書は通常、全てのTeledyne LLDユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Teledyneの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Teledyne LLDの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははTeledyne LLDの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Teledyne LLDに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Teledyne LLDデバイスの基本機能を使うにあたってのヒント。 Teledyne LLDのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Teledyne LLDに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるTeledyne LLDのメーカー/サービスへの連絡先に関する情報。

Teledyne LLDについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもTeledyne LLDの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがTeledyne LLDで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)