Manuel d’utilisation Cisco Systems 78-12510-02

20 pages 0.23 mb
Télécharger

Aller à la page of 20

Summary
  • Cisco Systems 78-12510-02 - page 1

    CHAPTER 5-1 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 5 Configuring the MGX RPM-PR This chapter describes how to complete a basic conf iguration of the MGX Route Processor Module (RPM-PR). It provides procedures for conf iguring A TM, Ethernet, and F ...

  • Cisco Systems 78-12510-02 - page 2

    5-2 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Booting the RPM-PR T o connect a modem to the auxiliary port on the RPM-PR, see Chapter 3, “Installing the MGX RPM-PR. ” Booting the RPM-PR When the RPM-PR is boote ...

  • Cisco Systems 78-12510-02 - page 3

    5-3 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Booting the RPM-PR RPM-PR Bootflash Precautions The RPM-PR bootf lash is used to store boot image, conf iguration and “run time” f iles. The Flash stores and access ...

  • Cisco Systems 78-12510-02 - page 4

    5-4 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Booting the RPM-PR drwxrwxrwx 1 0 0 13312 May 11 15:47 ./ drwxrwxrwx 1 0 0 13312 May 11 17:10 ../ -rwxrwxrwx 1 0 0 2253552 May 11 15:47 mpsm_t1e1_030.000.004.016-P2.fw ...

  • Cisco Systems 78-12510-02 - page 5

    5-5 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Booting the RPM-PR Step 1 Enter show ip int brief to display your router IP interfaces. Router# show ip int brief Interface IP-Address OK? Method Status Protocol Switch ...

  • Cisco Systems 78-12510-02 - page 6

    5-6 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Booting the RPM-PR switch autoSynch off ! ip kerberos source-interface any ip classless no ip http server ! ! ! line con 0 transport input none line aux 0 line vty 0 4 ...

  • Cisco Systems 78-12510-02 - page 7

    5-7 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Booting the RPM-PR Step 6 Enter show run to vie w your conf iguration. The conf iguration is similar to the one shown here. Router# show run Building configuration... C ...

  • Cisco Systems 78-12510-02 - page 8

    5-8 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Booting the RPM-PR Back Card Bay and Interface Port Numbers This section describes ho w to identify the back card bay and interface port numbers on the RPM-PR for all b ...

  • Cisco Systems 78-12510-02 - page 9

    5-9 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Booting the RPM-PR Router(config)# interface fastEthernet 1/1 Step 3 Y ou can assign an IP address and subnet mask to the interface with the ip addr ess conf iguration ...

  • Cisco Systems 78-12510-02 - page 10

    5-10 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Booting the RPM-PR 0 input packets with dribble condition detected 5 packets output, 300 bytes, 0 underruns(0/0/0) 5 output errors, 0 collisions, 0 interface resets 0 ...

  • Cisco Systems 78-12510-02 - page 11

    5-11 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Booting the RPM-PR Router# config t Enter configuration commands, one per line. End with CNTL/Z. Router(config)# interface fastethernet 1/1 Router(config-if)# media-ty ...

  • Cisco Systems 78-12510-02 - page 12

    5-12 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Verifying the Configuration MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 252/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepaliv ...

  • Cisco Systems 78-12510-02 - page 13

    5-13 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Verifying the Configuration 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input error ...

  • Cisco Systems 78-12510-02 - page 14

    5-14 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Verifying the Configuration Router# show version Cisco Internetwork Operating System Software IOS (tm) RPM Software (RPM-JS-M), Version 12.2(3.3)T, MAINTENANCE INTERIM ...

  • Cisco Systems 78-12510-02 - page 15

    5-15 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Verifying the Configuration MA Test History :00 MA Test History :01 EPROM format version 4 EPROM contents (hex): 0x00:04 22 40 02 22 C0 46 03 20 00 1C 0A 02 82 49 13 0 ...

  • Cisco Systems 78-12510-02 - page 16

    5-16 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Establishing 1:N Redundancy Between Two or More RPM-PR Cards .!!!! Success rate is 80 percent (4/5), round-trip min/avg/max = 1/1/1 ms Router# If the connection fails, ...

  • Cisco Systems 78-12510-02 - page 17

    5-17 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Establishing 1:N Redundancy Between Two or More RPM-PR Cards Note After you enter the addred command, the switch resets the secondary card; therefore, the secondary ca ...

  • Cisco Systems 78-12510-02 - page 18

    5-18 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Establishing 1:N Redundancy Between Two or More RPM-PR Cards Note The standby card must not hav e any conf igurations and must not be conf igured. Therefore, do not pr ...

  • Cisco Systems 78-12510-02 - page 19

    5-19 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Establishing 1:N Redundancy Between Two or More RPM-PR Cards 04 Empty --- --- --- --- 05 Empty --- --- --- --- 06 Failed/Empty AXSM_1OC48 MINOR NA NO REDUNDANCY 07 Act ...

  • Cisco Systems 78-12510-02 - page 20

    5-20 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Establishing 1:N Redundancy Between Two or More RPM-PR Cards Step 6 Continue this procedure from Step 2 for all remaining cards. Upgrading Non-redundant RPM-PR Cards T ...

Fabricant Cisco Systems Catégorie Router

Les documents que nous recevons du fabricant de l'appareilCisco Systems 78-12510-02 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Cisco Systems
- manuels d’utilisations 78-12510-02
- fiches produit Cisco Systems
- dépliants
- ou étiquettes-énergie Cisco Systems 78-12510-02
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Cisco Systems 78-12510-02.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Cisco Systems 78-12510-02, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Cisco Systems 78-12510-02. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Cisco Systems 78-12510-02.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Cisco Systems 78-12510-02, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Cisco Systems 78-12510-02 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Cisco Systems 78-12510-02.

Le manuel d’utilisation complet Cisco Systems, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Cisco Systems 78-12510-02 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Cisco Systems 78-12510-02, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lCisco Systems 78-12510-02 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Cisco Systems 78-12510-02 - qui devraient nous aider dans les premières étapes lors de l'utilisation Cisco Systems 78-12510-02
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Cisco Systems 78-12510-02
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Cisco Systems 78-12510-02 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Cisco Systems 78-12510-02?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Cisco Systems 78-12510-02, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Cisco Systems 78-12510-02 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Commentaires (0)