Cisco Systems 78-12510-02の取扱説明書

20ページ 0.23 mb
ダウンロード

ページに移動 of 20

Summary
  • Cisco Systems 78-12510-02 - page 1

    CHAPTER 5-1 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 5 Configuring the MGX RPM-PR This chapter describes how to complete a basic conf iguration of the MGX Route Processor Module (RPM-PR). It provides procedures for conf iguring A TM, Ethernet, and F ...

  • Cisco Systems 78-12510-02 - page 2

    5-2 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Booting the RPM-PR T o connect a modem to the auxiliary port on the RPM-PR, see Chapter 3, “Installing the MGX RPM-PR. ” Booting the RPM-PR When the RPM-PR is boote ...

  • Cisco Systems 78-12510-02 - page 3

    5-3 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Booting the RPM-PR RPM-PR Bootflash Precautions The RPM-PR bootf lash is used to store boot image, conf iguration and “run time” f iles. The Flash stores and access ...

  • Cisco Systems 78-12510-02 - page 4

    5-4 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Booting the RPM-PR drwxrwxrwx 1 0 0 13312 May 11 15:47 ./ drwxrwxrwx 1 0 0 13312 May 11 17:10 ../ -rwxrwxrwx 1 0 0 2253552 May 11 15:47 mpsm_t1e1_030.000.004.016-P2.fw ...

  • Cisco Systems 78-12510-02 - page 5

    5-5 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Booting the RPM-PR Step 1 Enter show ip int brief to display your router IP interfaces. Router# show ip int brief Interface IP-Address OK? Method Status Protocol Switch ...

  • Cisco Systems 78-12510-02 - page 6

    5-6 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Booting the RPM-PR switch autoSynch off ! ip kerberos source-interface any ip classless no ip http server ! ! ! line con 0 transport input none line aux 0 line vty 0 4 ...

  • Cisco Systems 78-12510-02 - page 7

    5-7 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Booting the RPM-PR Step 6 Enter show run to vie w your conf iguration. The conf iguration is similar to the one shown here. Router# show run Building configuration... C ...

  • Cisco Systems 78-12510-02 - page 8

    5-8 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Booting the RPM-PR Back Card Bay and Interface Port Numbers This section describes ho w to identify the back card bay and interface port numbers on the RPM-PR for all b ...

  • Cisco Systems 78-12510-02 - page 9

    5-9 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Booting the RPM-PR Router(config)# interface fastEthernet 1/1 Step 3 Y ou can assign an IP address and subnet mask to the interface with the ip addr ess conf iguration ...

  • Cisco Systems 78-12510-02 - page 10

    5-10 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Booting the RPM-PR 0 input packets with dribble condition detected 5 packets output, 300 bytes, 0 underruns(0/0/0) 5 output errors, 0 collisions, 0 interface resets 0 ...

  • Cisco Systems 78-12510-02 - page 11

    5-11 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Booting the RPM-PR Router# config t Enter configuration commands, one per line. End with CNTL/Z. Router(config)# interface fastethernet 1/1 Router(config-if)# media-ty ...

  • Cisco Systems 78-12510-02 - page 12

    5-12 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Verifying the Configuration MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 252/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepaliv ...

  • Cisco Systems 78-12510-02 - page 13

    5-13 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Verifying the Configuration 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input error ...

  • Cisco Systems 78-12510-02 - page 14

    5-14 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Verifying the Configuration Router# show version Cisco Internetwork Operating System Software IOS (tm) RPM Software (RPM-JS-M), Version 12.2(3.3)T, MAINTENANCE INTERIM ...

  • Cisco Systems 78-12510-02 - page 15

    5-15 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Verifying the Configuration MA Test History :00 MA Test History :01 EPROM format version 4 EPROM contents (hex): 0x00:04 22 40 02 22 C0 46 03 20 00 1C 0A 02 82 49 13 0 ...

  • Cisco Systems 78-12510-02 - page 16

    5-16 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Establishing 1:N Redundancy Between Two or More RPM-PR Cards .!!!! Success rate is 80 percent (4/5), round-trip min/avg/max = 1/1/1 ms Router# If the connection fails, ...

  • Cisco Systems 78-12510-02 - page 17

    5-17 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Establishing 1:N Redundancy Between Two or More RPM-PR Cards Note After you enter the addred command, the switch resets the secondary card; therefore, the secondary ca ...

  • Cisco Systems 78-12510-02 - page 18

    5-18 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Establishing 1:N Redundancy Between Two or More RPM-PR Cards Note The standby card must not hav e any conf igurations and must not be conf igured. Therefore, do not pr ...

  • Cisco Systems 78-12510-02 - page 19

    5-19 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Establishing 1:N Redundancy Between Two or More RPM-PR Cards 04 Empty --- --- --- --- 05 Empty --- --- --- --- 06 Failed/Empty AXSM_1OC48 MINOR NA NO REDUNDANCY 07 Act ...

  • Cisco Systems 78-12510-02 - page 20

    5-20 Cisco MGX Route Processor Module (RPM-PR) Installation and Configuration Guide Release 2.1, Part Number 78-12510-02 Rev. C1, August 31, 2004 Chapter 5 Configuring the MGX RPM-PR Establishing 1:N Redundancy Between Two or More RPM-PR Cards Step 6 Continue this procedure from Step 2 for all remaining cards. Upgrading Non-redundant RPM-PR Cards T ...

メーカー Cisco Systems カテゴリー Router

Cisco Systems 78-12510-02のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 78-12510-02の取扱説明書
- Cisco Systemsの製品カード
- パンフレット
- またはCisco Systems 78-12510-02の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Cisco Systems 78-12510-02の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Cisco Systems 78-12510-02の取り付け説明書、サービスマニュアル、簡易説明書、またはCisco Systems 78-12510-02のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Cisco Systems 78-12510-02の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Cisco Systems 78-12510-02デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがCisco Systems 78-12510-02を使用するのを助ける技術的文書のことです。説明書は通常、全てのCisco Systems 78-12510-02ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Cisco Systemsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Cisco Systems 78-12510-02の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははCisco Systems 78-12510-02の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Cisco Systems 78-12510-02に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Cisco Systems 78-12510-02デバイスの基本機能を使うにあたってのヒント。 Cisco Systems 78-12510-02のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Cisco Systems 78-12510-02に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるCisco Systems 78-12510-02のメーカー/サービスへの連絡先に関する情報。

Cisco Systems 78-12510-02についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもCisco Systems 78-12510-02の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCisco Systems 78-12510-02で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)